5117 SEAVIEW WAY 2019-09-19 - Laserfiche WebLink

TREX REVEAL® POST TTree® TREX REVEAL® POST Installation Instructions for Pressure-treated Wood Framing Installation Instructions for Pressure-treated Wood Framing LOCATION AND INSTALLATION OF POSTS LOCATION AND INSTALLATION OF POSTS/coNTINUED TREX REVEAL'" TREX REVEAL" IMPORTANT NOTES: Installing Standard Reveal Posts and/or Line Post Installation »EACH POST MUST BE ATTACHED AS SHOWN Reveal Crossover Posts on Pressure-treated Insert the(2)stainless steel barrier strips under the TO ENSURE A CODE COMPLIANT AND SAFE Wood Framing(Corner Post Installation) mounting bolt holes.Use composite shims or similar INSTALLATION. _ Cross bracing ., frame material(not provided)if posts are not plumb.Ensure » ALWAYS REFER TO YOUR LOCAL BUILDING CODE OFFICIAL PRIORIII - thatpost isplaced on deckingsurface so that it clears TO INSTALLING ANY RAILING SYSTEM TO ENSURE ALL CODE 2"x 8"Pressure-treated - ._..� ..-. AND SAFETY REQUIREMENTS ARE MET.TREX�'CANNOTBE �` Cross bracing frame - the rim joist and there is enough clearance on the HELD RESPONSIBLE FOR IMPROPER OR NON-RECOMMENDED "'-•�. underside blocking for the back plate to be installed. INSTALLATIONS. ��- Cross brad g-•., _ " » WHEN INSTALLING REVEAL POSTS ONACQ OR CCA SURFACES. frame - - "•�� USE AN APPROPRIATE ISOLATION BARRIER BETWEEN POST AND �• �^ _ - ----, Attach posts using four 3/8"x 6"(0.95 cm x SURFACE(CONTACT LOCAL BUILDING CODE OFFICIAL IF NEEDED). _., `- _ - ®� "�. 15.2 cm)hex cap bolts,washers,and nuts,along with » FOR INSTALLING STANDARD REVEAL POST AND/OR REVEAL I' _ using aluminum back plate on underside of blocking CROSSOVER POSTS,SEE BELOW ,='--- - .;. l_• . (back plate only required for 2.5"(6.4 cm)posts).This » FOR PRESSURE-TREATED POSTS,POST SLEEVES,AND SKIRTS,SEE to - .� back plate MUST be installed under the decking to DETAILED INSTRUCTIONS PROVIDED WITH REVEAL RAILING KITS. 3. Install two 2"x 8"(5.1 cm x 20.3 cm)cross bracing ensure this will meet code compliance.Reference SKU » ALL REVEAL STAIR INSTALLATIONS REQUIRE THE USE OF ,-----. frames in between joists at 7-1/4"(18.4 cm). part number ALPOSTHWDECK for required hardware 53"(134.6 CM)STAIR POST.MEASURED AND CUT TO APPROPRIATE Attach a total of twelve 3"(7.6 cm)pressure- and aluminum plate. LENGTH IF NECESSARY. 1. Install 2"x 8"(5.1 cm x 20.3 cm)cross bracing treated compatible screws(not provided). a IF CROSSOVER STAIR POST IS REQUIRED,USE STAIR POST(AGAIN frame in between joists at 7-1/4"(18.4 cm).Attach Installing Pressure- 0 CUT TO APPROPRIATE LENGTH IF NECESSARY)AND USE SWIVELa total of twelve 3"(7.6 cm)pressure-treated Blocking treated Posts,Post CROSSOVER BRACKET. boards compatible screws(not provided). Sleeves,and Skirts -____` ...., . 6. Attach posts using 1/2" 2"a s" TOOLS AND MATERIALS NEEDED © Blocking - (1.3 cm)carriage bolts. (2561.374 boards o I1mmm . » Drill and/or screw gun �, `° _, : » Minimum joist size is min. » 1/2"(1.27 cm)drill bit for wood �� "`A!� � 2"x 8"(5.1 cm x 5-LB"(13 cm)min.: » Blocking-2"x 8"(5.1 cin x 20.3 cm)pressure-treated Southern 1' !.= < R' "may Yellow Pine or equivalent .• .„,.... .!,%.-:-., � _ : _ �'d 20.3 cm). (� » Qty:36(per post)-3"pressure-treated compatible wood screws :>-t '' -= » Top bolts must be �`�►� 1"(2.5 cm)from top "� •.. - yd j ;-%------- of joists. CODE APPROVED POST APPLICATIONS `,.:.--;•-1.... » Bottom bolts must be 4. Install two 2"x 8"(5.1 cm x 20.3 cm)boards as 5-1/8"(13 cm)from top 2" 2.5blocking under post location.Securely attach bolts. - blocking using a total of twenty-four 3"(7.6 cm) POST SIZE 2" 2s" 2. Install two 2"x 8"(5.1 cm x 20.3 cm)boards as pressure-treated compatible screws(not provided). NOTE:Blocking can be 7 / / ` blocking under post location.Securely attach added for extra strength. 2x2 Post 2.5x2.5 Post(IRC) blocking using a total of twenty-four 3"(7.6 cm) ,5 WI . i pressure treated compatible screws(not provided). 7. Slide post sleeve skirt r <30"height Acceptable Acceptable post and down to i decking (Code Approval not (Code Approval nct 1, reston NOTE:TO ENSURE THE BLOCKING IS FULLY SECURE. deckingsurface. Applicable) Applicable) IRC Compliant No Yes USE THE AMOUNT OF SCREWS INDICATED ABOVE. r► Slide post sleeve over post and position inside IBC Compliant No No TIP:USE TWO ADDITIONAL SCREWS TO"SANDWICH" � post sleeve skirt. '�. BLOCKING BOARDS TOGETHER FOR EASIER ATTACHMENT TO FRAMING. rI. '� NOTE:Shims can be used to plumb post sleeves. barrier IMPORTANT NOTES: NOTE:RIM JOIST REMOVED TO SHOW PROPER »IF INSTALLING 42"(106.7 CM)RAILING AND USING PRESSURE- 5. TREATED POSTS WITH TREX POST SLEEVES,ENSURE THATA LONGER ATTACHMENT OF HARDWARE. PRESSURE-TREATED POST IS USED ALONG WITH LONGER POST SLEEVE BOTH CUT TOA HEIGHT OF 46"(126.8 CM)FROM DECKING NOTE:METAL BACKPLATE IS ONLY REQUIRED FOR SURFACE. 2.5"(6.4 CM)POST IN IRC INSTALLATIONS.(CONSULT LOCAL CODE OFFICIAL FOR MORE INFORMATION.) 0 El Have Questions? NOTE:Construction methods are always improving.Please ensure you Have Questions? NOTE:Construction methods are always improving.Please ensure you i-800-BUY-TREX have the most Glp-to-date installation instructions by visiting:trex.com TR REVEAL Post-0515 1-800-BUY-TREX have the most up-to-date installation instructions by visitingtrex.com iR-R_VEALMOS I()DV, 0I DATE: REVISIONS: Project Name: Construction Company: RACEN 13-20 Mark Dae A, 09.21-18 SHEET. A 10-02-18 CHRISTIAN PEREZ _ PROPOSED DECK RAILING - 5117 SEAVIEW WAY, EVERETT,WA 98203 PARCEL#:00567900300702 Drawn by: A2.5 DETAILS PER MANUFACTURER - ARKITECH 425-2403370