2710 WETMORE AVE 2019-11-07 - Laserfiche WebLink

B®SimplEx Addressable Initiation Peripherals UL, ULC, CSFM Listed; IDNet and MAPNET II Communicating Devices FM Approved* Model 4090-9008 Dual Contact Relay IAM Features Dual Contact Relay IAM (Individual Addressable 673' O o` Module): ^; • A single addressable point provides control and status tracking of two,2 A Form"C"contacts ,1 • Low power latching relay design allows IDNct or � - F. MAPNET II communications to supply both data and irt1 module power 1;01 — 9 1'01 • Relay is set to OFF on initial power up and upon loss of 1'01 . 1;©+',1 IDNet or MAPNET II communications --- For use with following Simplex control panels: • Model Series 4007ES,4010ES,4100ES,and 4100U fire alarm control panels for IDNet communications • Model Series 4100/4l OOU/4100ES,4120,4020,and 2120 Communicating Device Transponders(CDTs) 4090-9008 Dual Contact Relay IAM equipped with MAPNET II communications (shown approximately 1/2 size) Compact construction: • Mounts in standard 4"(102 mm)square electrical box, S•ecifications optional adapter bracket is available to mount in a 4 I l/6"square electrical box ZDNet or MAPNET II communications, • Screw terminals for wiring connections Communications 1 address per device • Visible LED flashes to indicate communications,can be Power Supplied by communications selected at panel to indicate activated state Installation 579-1040 • Optional 4"square box covers are available to allow Instructions LED to be viewed after installation IDNet Firmware Requires 3.12.04 or higher Contact Ratings*(not rated for incandescent switching) UL listed to Standard 864 Dual Form C contacts(DPDT)with Type terminal block access to Common, Descri•tion N.O.,and N.0 for each contact Dual Contact Relay IAMs allow fire alarm control 2 A @ 30 VDC, resistive from listed panels to control two remotely located Form"C"contact Power Limited e alarm supply using IDNet or MAPNET II addressable communications for both data and module power. Typical applications Nonpower Limited 0.5 A @ 125 VAC, resistive would be for switching local power for control functions Relay Fusing Each contact common is fused with a such as elevator capture,or control of HVAC components, 2 A fast acting non-time delay fuse pressurization fans,dampers,etc. Relay status is also * Provide external transient suppression as required per communicated requiring only one device address. application. DC inductive loads can typically be diode suppressed; 120 VAC loads may require RC networks or Product Selection varistors,depending on device type. Model Description Refer to Installation Instructions for additional information. 4090-9008 Dual Contact Relay IAM Wire Connections Screw terminals for in/out wiring, z 18 to 14 AWG wire(0.82 to 2.08 mm2) Optional Adapter Plates Up to 2500 ft(762 m)from control Model Description panel IDNet or 4090-9813 Adapter plate to fit 4"/i6"(119 mm)square MAPNET II Up to 10,000 ft(3048 m)total wiring electrical box Communications distance(including T-Taps) 4090-9801 For semi-flush Optional trim plate for 4" Wiring Reference Compatible with Simplex 2081-9044 mounted box boxes with LED viewing Overvoltage Protectors 4090-9802 For surface window, includes mounting 4'/8" H x 4"W x 1 %"D mounted box screws;galvanized steel Dimensions (105 mm x 102 mm x 35 mm) Mounting Plate Sheet metal,galvanized * This product has been approved by the California State Fire Marshal(CSFM)pursuant to Section 13144.1 of the California Health and Safety Code.See CSFM Listing Temperature 32°to 120° F(0°to 49°C), 7300-0026:0311 for allowable values and/or conditions concerning material presented in Range intended for indoor operation this document.Additional listings may be applicable;contact your local Simplex product Humidity Range Up to 93%RH at 100°F(38°C) supplier for the latest status.Listings and approvals under Simplex Time Recorder Co.are the property of Tyco Fire Protection Products. S4090-0014-3 11/2014