2710 WETMORE AVE 2019-11-07 - Laserfiche WebLink

Honeywell HPFF8, HPFF8CM, HPFF8E, HPFF8CME a • NAC Expander/Power Supply '■ .;� Description The Honeywell HPFF8(E) and HPFF8CM(E) are Notification Appliance Circuit(NAC)Expander Power Supplies designed to -- extend the power capabilities of existing NACs and provide power for auxiliary devices. The HPFF8 and HPFF8CM con- nects to any 12 or 24V Fire Alarm Control Panel (FACP) or , operates stand-alone. They provide regulated and filtered 24VDC power to four NAC's and an auxiliary output. The NAC outputs are rated at HPFF8 3.0 amps each and the auxiliary output is rated at 2.0 amps (this output is continuously supplied, even in alarm,and there- fore must be taken into account for power supply loading and battery size calculations).The combined output cannot exceed 8.0 amps. The HPFF8 and HPFF8CM provide independent output circuit ' supervision so in the event of a NAC fault they can notify the attached FACP. In addition they have a trouble memory fea- ` ,.- . Lure that displays past troubles (by NAC)for rapid diagnostics. Synchronization is built in for five appliance brands. The HPFF8 and HPFF8CM have two fully independent super- 44100, vised initiating circuits that can be used for synchronized 40, ;. "„ strobes and coded horns. Their NAC outputs may be config- ured as any of the following: HPFF8CM • four Class B(Style Y) • two Class A(Style Z) -Two Class B&one Class A. • two Class B and one Class A -Two Class A(Style Z). • four Class A with the optional HPP31076 Class A adapter -Four Class A(requires the HPP31076 Class A adapter). These power supplies contain an internal Battery charger • Four field-programmable operational modes: capable of charging up to 26.0 amp-hour(AH)batteries. -Pass-through. The HPFF8 is mounted in a lockable wall cabinet that can -Temporal generator. accommodate up to two 18AH batteries. The HPFF8CM is designed to mount in Honeywell's large equipment enclosure -Sync generator. (EQBB-D4; order separately). Up to four HPFF8CM supplies -Pass-through Filtered. can be mounted in a D-sized EQ cabinet. Each HPFF8CM can • Temporal coding and sync protocols compatible with the fol- accommodate two 12AH batteries. lowing notification appliance brands: One of the most challenging aspects of a retrofit application is -System Sensor. locating the existing End-of-Line(EOL) resistor. In these appli- -Faraday. cations that have EOL values other than the 3.9k normally used with the HPFF8, a single resistor matching the existing -Amseco. EOL can be used as a reference for all the outputs. This fea- -Cooper-Wheelock. ture speeds installation and system checkout because the -Gentex. actual EOL does not need to be located and changed in the • Protocol pass-through for synchronizing large systems. circuit.The reference resistor must be within the range of 1.9k to 25k. • Two fully independent supervised input/output control circuits. NOTE:4 separate programming resistors for the HPFF8 are pro • Redundant activation operation for survivability. vided in the hardware kit shipped with each HPFF8(E) and • Supports FACP's Selectable Silence ability. HPFF8CM(E). They are 3.9K(5 of these are provided, need only • 2.0 amp auxiliary continuously supplied output. 1 for programming),2.2K(1 each),4.7K(1 each)and 10K(1 each) • Eight status LEDs. Features • Supervised AC input, battery voltage,auxiliary output,char- ger,and earth ground faults. • Listed to UL Standard 864,9th edition. • Trouble indication for supervision of the following: • Four (4) power limited supervised notification application -NAC circuits. circuits (NAC's) capable of supplying +24VDC at 3.0 amp maximum each. -Auxiliary output. • NAC output circuits may be configured as any of the follow- -AC input. ing: -Battery charger voltage. -Four Class B(Style Y). -Earth ground faults. • Optional two-hour delay for AC loss. /�o