|
' HardiePlank®Lap Siding
<br /> 7/4—ii.
<br /> COLORPLUS®TECHNOLOGY CAULKING,TOUCH-UP&LAMINATE
<br /> •Care should be taken when handling and cutting James Hardie®ColorPlus®products.During installation use a wet soft cloth or soft brush to gently wipe off any
<br /> residue or construction dust left on the product,then rinse with a garden hose.
<br /> •Touch up nicks,scrapes and nail heads using the ColorPlus®Technology touch-up applicator.Touch-up should be used sparingly.
<br /> If large areas require touch-up,replace the damaged area with new HardiePlanlc®lap siding with ColorPlus®Technology.
<br /> •Laminate sheet must be removed immediately after installation of each course.
<br /> •Terminate non-factory cut edges into trim where possible,and caulk.Color matched caulks are available from your ColorPlus®product dealer.
<br /> •Treat all other non-factory cut edges using the ColorPlus Technology edge coaters,available from your ColorPlus product dealer.
<br /> Note:James Hardie does not warrant the usage of third party touch-up or paints used as touch-up on James Hardie ColorPlus products.
<br /> Problems with appearance or performance arising from use of third party touch-up paints or paints used as touch-up that are not James Hardie touch-up will not be covered
<br /> under the James Hardie ColorPlus Limited Finish Warranty.
<br /> PAINTING JAMES HARDIE®SIDING
<br /> COVERAGE CHART/ESTIMATING GUIDE AND TRIM PRODUCTS WITH
<br /> Number of 12 ft.planks,does not include waste COLORPLUS®TECHNOLOGY
<br /> COVERAGE AREA When repainting ColorPlus products,James
<br /> LESS Hardie recommends the following regarding
<br /> OPENINGS surface preparation and topcoat
<br /> HARDIEPLANK®LAP SIDING WIDTH •
<br /> p p P application:, n
<br /> • Ensure the surface is clean,dry,and free of any
<br /> SQ 51/4 61/4 71/4 71/2 8 81/4 91/4 91/2 12 dust,dirt,or mildew
<br /> (1 SQ=100 sq.ft.) (exposure) 4 5 6 61/4 6 3/4 7 8 81/4 10 3/4 • Repriming is normally not necessary
<br /> •100%acrylic topcoats are recommended
<br /> 1 25 20 17 16 15 14 13 13 9 • DO NOT use stain,oil/alkyd base paint,or
<br /> 2 50 40 33 32 30 29 25 25 19
<br /> 3 75 60 50 48 44 43 38 38 28 powder coating on James Hardie®Products.
<br /> - 4 100 80 67 64 59 57 50 50 37 •Apply finish coat in accordance with paint
<br /> 5 125 100 83 80 74 71 63 63 47 manufacturers written instructions regarding
<br /> 6 150 120 100 96 89 86 75 75 56
<br /> 7 175 140 117 112 104 100 88 88 65 coverage,application methods,and application
<br /> 8 200 160 133 128 119 114 100 100 74 temperature
<br /> 9 225 180 150 144 133 129 113 113 84 • DO NOT caulk nail heads when using ColorPlus
<br /> 10 250 200 167 160 148 143 125 125 93
<br /> 11 275 220 183 176 163 157 138 138 102 products,refer to the ColorPlus touch-up
<br /> 12 300 240 200 192 178 171 150 150 112 section
<br /> 13 325 260 217 208 193 186 163 163 121
<br /> 14 350 280 233 224 207 200 175 175 130
<br /> 15 375 300 250 240 222 214 188 188 140
<br /> 16 400 320 267 256 237 229 200 200 149
<br /> 17 425 340 283 272 252 243 213 213 158
<br /> 18 450 360 300 288 267 257 225 225 167
<br /> 19 475 380 317 304 281 271 238 238 177
<br /> 20 500 400 333 320 296 286 250 250 186
<br /> This coverage chart is meant as a guide.Actual usage is subject to variables such as building design.
<br /> James Hardie does not assume responsibility for over or under ordering of product.
<br /> ADDITIONAL HANDLING REQUIREMENTS Pull from across the stack Do not go down the stack
<br /> IMPORTANT:To prevent damage to the drip edge,extra care should be � ®
<br /> ,11
<br /> taken when removing planks from the pallet,while handling,and
<br /> when installing with a lap gauge.Planks are interlocked together on
<br /> the pallet,therefore they should be removed from the pallet
<br /> horizontally(side to side)to allow planks to unlock themselves from '
<br /> a ��
<br /> one another. =Z,==
<br /> HS11117 P4/4 04/18
<br /> z DANGER:May cause cancer if dust from product is inhaled.Causes damage to lungs and respiratory system through prolonged or repeated inhalation of dust from product.Refer to the current product Safety Data Sheet before use.
<br /> = The hazard associated with fiber cement arises from crystalline silica present in the dust generated by activities such as cutting,machining,drilling,routing,sawing,crushing,or otherwise abrading fiber cement,and when cleaning
<br /> up,disposing of or moving the dust.When doing any of these activities in a manner that generates dust you must(1)comply with the OSHA standard for silica dust and/or other applicable law,(2)follow James Hardie cutting
<br /> 3 instructions to reduce or limit the release of dust;(3)warn others in the area to avoid breathing the dust;(4)when using mechanical saw or high speed cutting tools,work outdoors and use dust collection equipment;and(5)if no
<br /> a other dust controls are available,wear a dust mask or respirator that meets NIOSH requirements(e.g.N-95 dust mask).During clean-up,use a well maintained vacuum and filter appropriate for capturing fine(respirable)dust or use
<br /> h wet clean-up methods-never dry sweep.
<br /> ,WARNING:This product can expose you to chemicals including respirable crystalline silica,which is known to the State of California to cause cancer.For more information go to P65Wamings,cagov.
<br /> RECOGNmON:In accordance with ICC-ES Evaluation Report ESR-2290,HardiePlank®lap siding is recognized as a suitable alternate to that specified in:the 2006,2009,&2012 International Residential Code for One-and Two-Family
<br /> Dwellings,and the 2006,2009,&2012 International Building Code,.HardiePlank lap siding is also recognized for application in the following:City of Los Angeles Research Report No.24862,State of Florida listing FL#889,Dade County,
<br /> Florida NOA No.02-0729.02,U.S.Dept.of HUD Materials Release 1263c,Texas Department of Insurance Product Evaluation EC-23,City of New York MEA 223-93-M,and California DSA PA-019.These documents should also be consult
<br /> for additional information concerning the suitability of this product for specific applications. /0//6
<br /> ®2018 James Hardie Building Products,Inc.All rights reserved TM,SM and® Product warranties,safety information and additional installation SJamesHardie
<br /> denote trademarks or registered trademarks of James Hardie Technology Limited. information are available atjameshardiepros.com
<br />
|