Cummins Inc. 12/30/2020 - Laserfiche WebLink

Sales and Service NOTES AND EXCEPTIONS: This proposal is based on Spec sections 26 24 13 26 27 16&26 32 13 provided by City of Everett and drawings SWBD GSB2 Rev2 WBD SSB-1 Rev1 SWBD SSB-2A Rev 1 SWBD SSB-2B Rev 1 provided by SAZAN.We know of no addenda, drawings, or relevant spec sections. #26 32 13 2.8 E-Calcium Silicate Exhaust Insulation By Installing Contractor. Not Provided By Cummins 2.10 Oil Heaters Not Provided. Not Factory Option 2.12 RTDs not provided on 1000 KW unit or 500 KW trailer. Not Factory Option- #26 24 13 1.5.A.1.b.6&7—These drawings not available at submittal time. 1.5.A.1.c—Not available at submittal time. 3.1 —Installation by others 3.4—By others 3.5—By others •Approval from the local utility MUST be obtained before this equipment may be connected, and/or operated with the facility bus. •The price contained in this quotation is based on the sequence of operation either referenced to, and/or described in this document as it pertains to the equipment indicated on the previous pages.Any variations to this sequence, and/or any additional circuit breakers, switches,fuses, etc.,to supply, monitor and/or control will require re-pricing. accn orin will bn the responsibility of the quoting distributor • Engine/Generator control and monitoring, voltage regulation, paralleling, synchronizing, and some protective circuits will be accomplished via PowerCommand TM Control and/or PowerCommand TM Paralleling. 1. The digital display on the PowerCommand genset paralleling control includes a synchroscope function for monitoring the phase difference(in degrees,faster or slower than bus) between the generator set and the system bus.An indicator is provided to advise the operator when the generator set is within specified paralleling parameters. 2. Paralleling control functions(synchronizing, load sharing, etc.)and paralleling protective functions (0/U bus voltage/frequency, overload, and phase protection) are provided by the PowerCommand generator set controls that are resident on the gensets. COVID 19 SUPPLEMENTAL STATEMENT AS A RESULT OF THE OUTBREAK OF THE DISEASE COVID-19 ARISING FROM THE NOVEL CORONAVIRUS,TEMPORARY DELAYS IN DELIVERY, LABOUR OR SERVICES FROM CUMMINS AND ITS SUB-SUPPLIERS OR SUBCONTRACTORS MAY OCCUR. AMONG OTHER FACTORS, CUMMINS' DELIVERY OBLIGATIONS ARE SUBJECT TO CORRECT AND PUNCTUAL SUPPLY FROM OUR SUB-SUPPLIERS OR SUBCONTRACTORS, AND CUMMINS RESERVES THE RIGHT TO MAKE PARTIAL DELIVERIES OR MODIFY ITS LABOUR OR SERVICE. WHILE CUMMINS SHALL MAKE EVERY COMMERCIALLY REASONABLE EFFORT TO MEET THE DELIVERY, SERVICE OR COMPLETION OBLIGATIONS SET FORTH HEREIN, SUCH DATES ARE SUBJECT TO CHANGE. INTERNATIONAL BUILDING CODE(IBC)CERTIFICATION The products in this quotation identified as meeting the requirements of the 2009 IBC have been certified by their respective manufactures via a combination of analytical testing and shaker table testing. Not all products have been shaker table tested. OFFICE OF STATEWIDE HEALTH PLANNING AND DEVELOPMENT(OSHPD) OSHPD seismic requirements are continuing to evolve. Please contact Cummins for the most current requirements for meeting OSHPD applications. SELECTIVE COORDINATION FOR NATIONAL ELECTRIC CODE(NEC)ARTICLE 700 AND 701 LOADS Cummins generators are equipped with the manufacturer's recommended circuit breaker. Information regarding this device can be supplied upon request.This quotation is not valid if any changes to this circuit breaker(s) is required to coordinate with other devices in the electrical distribution system. If changes are required,the customer must provide a copy of the coordination study listing the manufacturers part number of the disconnect device to be supplied with the generator and a revised quotation will be issued. TRANSFER SWITCH WITHSTAND AND CLOSE RATINGS Quotation: 0-129133-Q-07903 Doc Ref: Q-07903-20201026-0951 Page 6 of 11