10521 19TH AVE SE 2022-05-23 - Laserfiche WebLink

• Building Permit Plark:4 Checklist, pg. 3 ENV-4 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Project Title: SILVER PLAZA RETAIL AND OFFICE SHELL Date Applicability Code Location in Build (yes,no,na) Section Component Compliance information required in permit documents Documents Departme In single story buildings,provide list of enclosed areas that exceed 2,500 sf,have ceiling height greater than 15 ft,and are space types required to comply with this provision.For each area identify space type,floor area, floor to ceiling height,and any exception taken; Spaces in single For each area provide calculations for percentage of conditioned floor area na C402.4.2 story buildings located within a daylight zone including skylight and eligible sidelight requiring skylights daylight zones; For each area provide calculations for percentage of skylight area,OR; Provide calculations for skylight effective aperture(Equation C4-5); Indicate haze factor of skylight glazing material or diffuser AIR LEAKAGE Indicate location of continuous air barrier on plans and sections; Air barrier yes C402.5.1.1 construction and Provide details for all joints,transitions in materials,penetrations in air sealing barrier and note method of sealing(caulked,gasketed,or other approved method) A500(pending) Rooms containing Indicate that room(s)containing non-direct vent appliances is isolated from open combustion inside the thermal envelope with a sealed air barrier, including doorway na C402.5.3 fuel burning gasketing and sealing around ductwork and piping penetrations; appliances used for Indicate insulation provided in wall,floor and ceiling of the room envelope, space conditioning and insulation required on combustion air ductwork Access openings Indicate locations of all access openings and doors to shafts,chutes, yes C402.5.4 and doors to shafts, stairways and elevators; stairs shown and chutes,stairways Indicate method of gasketing,weatherstripping and sealing of these doors located on and doors openings A121 Indicate locations of all stairway enclosure,elevator shaft and building Outdoor air intakes, pressurization relief openings,outside air intakes and exhaust openings; C402.5.5 es exhausts and relief y C403.2.4.3 Note in envelope plans that all relief,outside air intake and exhaust openings openings shall be provided with dampers in accordance with Mechanical Note 9 added to Section C403.2.4.3 sheet A121 Indicate method of sealing between light fixture housing and wall or ceiling; na C402.5.8 Recessed lighting in building envelope Note in envelope plans that all recessed lighting fixtures shall be IC rated and have an air leakage rating not greater than 2 cfm per ASTM E283 test; include these requirements in lighting fixture schedules na C402.5.6 Loading dock seals Indicate weather seal at cargo and loading dock doors Indicate locations and dimensions of vestibules and air curtains; Indicate exception and criteria utilized for all building entrances and exits vestibules 101 yes C402.5.7 Vestibules that do not have a vestibule or air curtain; EAST ENTRY and Indicate required performance for air curtains installed per exception 7; 100 WEST ENTRY For unconditioned vestibules,indicate which envelope assembly(interior are shown on or exterior)complies with the requirements for a conditioned space A121 Indicate on plans the air barrier boundaries and area calculations on all six sides of the air barrier; Indicate air barrier test method in accordance with ASTM E779 or approved equivalent; C103.2 Building air leakage Indicate required maximum leakage rate for compliance. yes C402.5.1.2 test Include the following requirements in project documents:(1)Submit air barrier test report to jurisdiction once test is completed;(2)If test results exceed 0.4 cfmlft2 at 0.3 in.wg,then visually inspect air barrier and seal noted sources of leakage;(3)Submit a follow-up report to jurisdiction noting corrective measures taken; (4)Include air barrier test report in compliance documentation provided to owner. A500(pending) If"no" is selected for any question, provide explanation: