2701 ROCKEFELLER AVE 2020 Plans 2023-09-18

• DOORS, DOORWAYS, AND GATES4. U) co ICC A117.1-2009 TABLE 404.2.3.2 - MANEUVERING CLEARANCES FOR MANUAL SWINGING DOORS °�° 404 DOORS, DOORWAYS, AND GATES rcJ TYPE OF USE MINIMUM CLEARANCES I co `� rnm 404.1 GENERAL. DOORS, DOORWAYS, AND GATES THAT ARE PART OF AN ACCESSIBLE ROUTE APPROACH PERPENDICULAR TO BEYOND LATCH I c • DOOR SIDE o N SHALL COMPLY WITH 404. DIRECTION `DOOR 1 PARALLEL TO DOOR a, rnLL N `E .c 2 404.2 MANUAL DOORS, DOORWAYS, AND MANUAL GATES. MANUAL DOORS AND DOORWAYS AND FROM FRONT I PULL 60 INCHES (1525 MM) 18 INCHES (455 MM) 1__L 3 fo N • MANUAL GATES INTENDED FOR USER PASSAGE SHALLICOMPLY WITH 404.2. Q . N FROM FRONT PUSH 48 INCHES (1220 MM) 0 INCHES (0 MM)3 °' SHALL COMPLY WITH 404.2 3 AND DOUBLE-LEAF 404.2.1 DOORSGATES. AT LEAST F'ONE OTHE ACTIVE LEAVES OF DOORWAYS —_ o 04.2.4. FROM HINGED SIDE PULL 60 INCHES (1525 MM) 36 INCHES (915 MM) v WITH TWO LEAVES • CC) 404.2.2 CLEAR WIDTH. DOOR OPENINGS SHALL PROVIDE A CLEAR WIDTH OF 32 INCHES (815 MM) FROM HINGED SIDE PULL 54 INCHES (1370 MM) 42 INCHES (1065 MM) V MINIMUM. CLEAR OPENINGS OF DOORWAYS WITH SWINGING DOORS SHALL BE MEASURED BETWEEN THE FACE OF THE DOOR AND THE STOP, WITH THE DOOR OPEN 90 DEGREES. s 814L OPENINGS MORE THAN 24 INCHES (610 MM) DEEP SHALL PROVIDE A CLEAR OPENING OF 36 FROM HINGED SIDE PUSH 42 INCHES (1065 MM) 22 INCHES (1370 MM) INCHES (915 MM) MINIMUM. THERE SHALL BE NO PROJECTIONS INTO THE REQUIRED CLEAR t ,i.. x •• '.;: ,� 1 OPENING WIDTH LOWER THAN 34 INCHES (865 MM) ABOVE THE FINISH FLOOR OR GROUND. FROM LATCH SIDE PULL 48 INCHES (1220 MM) 24 INCHES (610 MM) " PROJECTIONS INTO THE CLEAR OPENING WIDTH BETWEEN 34 INCHES (865 MM) AND 80 INCHES ocuHKi BARNES • (2030 MM) ABOVE THE FINISH FLOOR OR GROUND SHALL NOT EXCEED 4 INCHES (100 MM). FROM LATCH SIDE PUSH 42 INCHES (1065 MM)2 24 INCHES (610 MM) EXCEPTIONS: 1. DOOR CLOSERS AND DOOR STOPS SHALL BE PERMITTED TO BE 78 INCHES (1980 1 ADD 6 INCHES (150 MM) IF CLOSER AND LATCH PROVIDED. MM) MINIMUM ABOVE THE FINISH FLOOR OR GROUND. 2ADD 6 INCHES (150 MM) IF CLOSER PROVIDED. 3ADD 12 INCHES (305 MM) BEYOND LATCH IF CLOSER AND LATCH PROVIDED. 404.2.3 MANEUVERING CLEARANCES. MINIMUM MANEUVERING CLEARANCES AT DOORS SHALL a BEYOND HINGE SIDE. COMPLY WITH 404.2.3. MANEUVERING CLEARANCES AND SHALL INCLUDE THE FULL CLEAR OPENING WIDTH OF THE DOORWAY. REQUIRED DOOR MANEUVERING CLEARANCES SHALL NOT . INCLUDE KNEE AND TOE CLEARANCE. i • PULL SIDE PULL SIDE 404.2.3.1 FLOOR SURFACE. FLOOR SURFACE WITHIN THE MANEUVERING CLEARANCES SHALL r.i, HAVE A SLOPE NOT STEEPER THAN 1:48 AND SHALL COMPLY WITH SECTION 302. r -4- — — I 404.2.3.2 SWINGING DOORS. SWINGING DOORS AND SHALL HAVE MANEUVERING CLEARANCES Z 18" MIN. I • 24" PREFERRED I COMPLYING WITH TABLE 404.2.3.2. 1 �. X MIN. g • 404.2.3.3 SLIDING AND FOLDING DOORS. SLIDING DOORS AND FOLDING DOORS SHALL HAVE I" I I } W MANEUVERING CLEARANCES COMPLYING WITH TABLE 404.2.3.3. ♦ ..1 C 404.2.3.4 DOORWAYS WITHOUT DOORS. DOORWAYS WITHOUT DOORS THAT ARE LESS THAN 36 I . . W Q O INCHES (915 MM) IN WIDTH SHALL HAVE MANEUVERING' CLEARANCES COMPLYING WITH TABLE rNOTE: X =36" MIN. IF Y= I W O 404.2.3.4 j j 60". X= 42" MIN. IF Y=54". J 404.2.3.5 RECESSED DOORS. WHERE ANY OBSTRUCTION WITHIN 18 INCHES (455 MM) OF THE • • 4LW ]? LATCH SIDE OF A DOORWAY PROJECTS MORE THAN 8 INCHES (205 MM) BEYOND THE FACE OF THE 4 MI PUSH SIDE W DOOR, MEASURED PERPENDICULAR TO THE FACE OF THE DOOR, MANEUVERING CLEARANCES PULL SIDE 1 N o Y I- FOR A FORWARD APPROACH SHALL BE PROVIDED. I 12" MIN.* 22" MIN.y U W • r - - 7- - 1 I I '� "II Q 404.2.4 THRESHOLDS. IF PROVIDED, THRESHOLDS AT DOORWAYSw SHALL BE 1/2 INCH (13 MM) z 1 I I z -- r-- . . — r— - I O � W MAXIMUM IN HEIGHT. RAISED THRESHOLDS AND CHANGES IN LEVEL AT DOORWAYS SHALL I I I I I , I I COMPLY WITH SECTIONS 302 AND 303. I • 2 � I I _ W I I I • I It EtO W 404.2.5 TO DOORS IN SERIES. DISTANCE BETWEEN TWO HINGED OR PIVOTED DOORS IN SERIES } I I I . I I r N SHALL BE 48 INCHES (1220 MM) MINIMUM PLUS THE WIDTH OF ANY DOOR SWINGING INTO THE } SPACE. THE SPACE BETWEEN THE DOORS SHALL PROVIDE A TURNING SPACE COMPLYING WITH �a • , O SECTION 304. • 404.2.6 DOOR HARDWARE. HANDLES, PULLS, LATCHES, LOCKS, AND OTHER OPERABLE PARTS ON 4 N ACCESSIBLE DOORS SHALL HAVE A SHAPE THAT IS EASY TO'GRASP WITH ONE HAND AND DOES OF NOTE: Y=54" MIN. I INOTE: Y = 48" MIN. IF DOOR HAS1 f NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTINGTHE WRIST TO OPERATE. OPERABLE PARTS OF SUCH HARDWARE SHALL BE 34 INCHES (865 MM) MINIMUM AND 48 INCHES (1220 MM) IF DOOR HAS CLOSER , BOTH A LATCH AND A CLOSER. MAXIMUM ABOVE THE FLOOR. WHERE SLIDING DOORS ARE IN THE FULLY OPEN POSITION, * IF BOTH CLOSER AND LATCH xi OPERATING HARDWARE SHALL BE EXPOSED AND USABLE FROM BOTH SIDES. PROVIDED, EXCEPTION: LOCKS USED ONLY FOR SECURITY PURPOSES AND NOT USED FOR NORMAL • • OPERATION SHALL NOT BE REQUIRED TO COMPLY WITH SECTION 404.2.6. • p �yPUSH SIDE (X) 24" t. 404.2.7.1 DOOR CLOSERS. DOOR CLOSERS SHALL BE ADJUSTED SO THAT FROM AN OPEN I XMIN.� PUSH SIDE . POSITION OF 90 DEGREES, THE TIME REQUIRED TO MOVE THE DOOR TO AN OPEN POSITION OF 12 r T —— - r - — - — - I ♦ N. DEGREES SHALL BE 5 SECONDS MINIMUM. z I I n I I Z I I v I I I g 404.2.7.2 SPRING HINGES. DOOR SPRING HINGES SHALL BE ADJUSTED SO THAT FROM AN OPEN I' . I I . POSITION OF 70 DEGREES, THE DOOR SHALL MOVE TO'ITHE CLOSED POSITION IN 1.5 SECONDS d I' I , I I MINIMUM. t� . IIIIIIIIIII • 404.2.8 DOOR-OPENING FORCE. FIRE DOORS SHALL HAVE THE MINIMUM OPENING FORCE • , ALLOWABLE BY THE APPROPRIATE ADMINISTRATIVE AUTHORITY. THE FORCE FOR PUSHING OR • PULLING OPEN DOORS OTHER THAN FIRE DOORS SHALL BE AS FOLLOWS: 1. INTERIOR HINGED DOOR: POUNDS SLIDING OR FOLDING DOOR: 5.0 POUNDS (22.2 N) MAXIMUM. THESE FORCES DO NOT THE FORCE REQUIRED TO RETRACT LATCH BOLTS 1NOTE:X=12" MIN. IF DOOR HAS j NOTE:Y=48" MIN. IF DOOR HAS f. OR DISENGAGE OTHER DEVICES THAT HOLD THE DOOR IN A CLOSED POSITION. ;BOTH A LATCH AND A CLOSER ( ! BOTH A LATCH AND A CLOSER) . . 404.2.9 DOOR SURFACE. DOOR SURFACES WITHIN 10 INCHES (255 MM) OF THE FLOOR, MEASURED " VERTICALLY, SHALL BE A SMOOTH SURFACE ON THE PUSH SIDE EXTENDING THE FULL WIDTH OF THE DOOR. PARTS CREATING HORIZONTAL OR VERTICAL JOINTS IN SUCH SURFACE SHALL BE 32" MIN lj • . WITHIN 1/16 INCH (1.6 MM) OF THE SAME PLANE AS THE OTHER. CAVITIES CREATED BY ADDED CLEA • KICK PLATES SHALL BE CAPPED. CLEAR OPENINGS MUST BE BETWEEN THE r \ FLOOR IN ITS 90 DEGREE OPEN POSITION AND \ THE FACE OF THE STOP _ EXCEPTIONS: 1. SLIDING DOORS SHALL NOT BE REQUIRED O COMPLY WITH SECTION 404.2.9. 2. 90 .. ) REGISTERED TEMPERED GLASS DOORS WITHOUT STILES AND HAVING A BOTTOM RAIL OR SHOE WITH THE TOP ARCHITECT LEADING EDGE TAPERED AT NO LESS THAN 60 DEGREES FROM THE HORIZONTAL SHALL NOT BE I _ i - ��. � + REQUIRED TO COMPLY WITH THE 10-INCH (255 MM) BOTTOM RAIL HEIGHT REQUIREMENT. 3. STOP --" DOORS THAT DO NOT EXTEND TO WITHIN 10 INCHES (255 MM OF THE FLOOR SHALL NOT BE gg W &COT U CRK I STATE OF WASHINGTON REQUIRED TO COMPLY WITH SECTION 404.2.9. 4 • .. NOTE: ALL DOORS IN ALCOVES SHALL COMPLY WITH THE 404.2.10 VISION LITES. DOORS AND SIDELITES ADJACENT TO,DOORS CONTAINING ONE OR MORE CLEARANCES FOR FRONT APPROACHES. a. GLAZING PANELS THAT PERMIT VIEWING THROUGH THE PANELS SHALL HAVE THE BOTTOM OF AT If 4 DATE: 01/25/21 • LEAST ONE PANEL ON EITHER THE DOOR OR AN ADJACENT SIDELITE 43 INCHES (1090 MM) tJOB NO. 19 48 MAXIMUM ABOVE THE FLOOR. I 1. THE FLOOR OR LANDING ON EA. SIDE OF AN EXIT DOOR SHALL BE LEVEL AND CLEAR. PERMIT NO.B2006-044 I THE LEVEL AREA SHALL HAVE A LENGTH IN THE DIRECTION OF THE DOOR SWING OF AT 62009 016 EXCEPTION: VISION LITES WITH THE LOWEST PART MORE THAN 66 INCHES (1675 MM) ABOVE THE LEAST 60" AND LENGTH OPPOSITE THE DIRECTION OF DOOR SWING 44" AS MEASURED AT FLOOR SHALL NOT BE REQUIRED TO COMPLY WITH SECTION'404.2.10. RIGHT ANGLES TO THE PLANE OF THE FLOOR IN ITS CLOSED POSITION. REVISIONS: 404.3 AUTOMATIC DOORS. AUTOMATIC DOORS AND AUTOMATIC GATES SHALL COMPLY WITH 2. THE WIDTH OF THE LEVEL AREA ON THE SIDE TO WHICH THE DOOR SWINGS SHALL ' ` .. DATE DESCRIPTION SECTION 404.3. FULL POWERED AUTOMATIC DOORS SHALL COMPLY WITH ANSI/BHMA A156.10 EXTEND 24" PAST THE STRIKE EDGE OF THE DOOR FOR EXTERIOR DOORS AND 18" PAST LISTED IN SECTION 105.2.4. POWER-ASSIST AND LOW-ENERGY DOORS SHALL COMPLY WITH THE STRIKE EDGE FOR INTERIOR DOORS. 4 ANSI/BHMA A156.19 LISTED IN SECTION 105.2.3. I EXCEPTION: DOORS, DOORWAYS, AND GATES DESIGNED TO BE OPERATED ONLY BY SECURITY - o ' PERSONNEL SHALL NOT BE REQUIRED TO COMPLY WITH SECTIONS 404.3.2, 404.3.4, AND 404.3.5. REQUIRED I NOTE: PROVIDE BUMPER IN I POCKET TO PREVENT DOOR 404.3.1 CLEAR WIDTH. DOORWAYS SHALL HAVE A CLEAR OPENING WIDTH OF 32 INCHES 815 MM) I SPACE 18" MIN. FROM FULLY RECEDING ( I '--,N 24" PREFERRED IN POWER-ON AND POWER-OFF MODE. THE MINIMUM CLEAR OPENING FOR AUTOMATIC DOOR I 32" MINI. SYSTEMS SHALL BE BASED ON THE CLEAR OPENING WIDTH PROVIDED WITH ALL LEAFS IN THE I \ I / - !- t OPEN POSITION. 1! ISSUE; • L =` I I * SHORING/EX 05/08/20 404.3.2 MANEUVERING CLEARANCES. MANEUVERING CLEARANCES AT POWER-ASSISTED DOORS REQUIRED NOTE: X = 12° \ j PHASE I 06/22/20 • SHALL COMPLY WITH 404.2.3. CLEAR STOP SPACE WITH CLOSER t, BID PROG SET 07/13/20 • 404.3.3 THRESHOLDS. THRESHOLDS AND CHANGES IN LEVEL AT DOORWAYS SHALL COMPLY WITH AND LATCHSET PHASE II 08/31/20 SECTION 404.2.4. I GMP 09/30/20 ALL LEVEL DOOR HANDLES ARE TO OPERATE AT A FORCE NO GREATER ALL REV 1 01/19/21 404.3.4 TWO DOORS IN SERIES. DOORS IN SERIES SHALL COMPLY WITH SECTION 404.2.5. IFC SET 01/25/21 THAN A SLB. FORCE AND WITHOUT EXCESSIVE BODY MOVEMENT OR PERMIT REV 2 02/19/21 SPECIAL KNOWLEDGE. LEVELS TO BE OPERABLE WITH ONE HAND AND NOT • 404.3.5 CONTROL SWITCHES. MANUALLY OPERATED CONTROL SWITCHES SHALL COMPLY WITH REQUIRE GRASPING, PINCHING OR TWISTING. DOORS TO SWING AND BE IFC SET 02/19/21 SECTION 309. THE CLEAR FLOOR SPACE ADJACENT TO THE CONTROL SWITCH SHALL BE LOCATED OPERABLE AT A FORCE NO GREATER THAN SLB. ALL DOORS MUST PROVIDE PERMIT REV 3 05/26/21 BEYOND THE ARC OF THE DOOR. MINIMUM MANEUVERING CLEARANCES. ADA DOOR AUTOMATIC CLOSER - (IF NEC) \-�, CI i Y OT VERETT • ROOM IDENTIFICATION REVIEWED FOR PERMIT (IF NEC) VIEWING PANEL — (IF NEC) : 1 LEVEL DOOR HANDLE _ g SHEET NO: o f '1 In • \l'el. - NOTE: THRESHOLD P �, MAX. HT. 1/2" A.F.F. M Ns' I A8 . 03 REFERENCE CODE: NOTE: FLOOR MAT FLUSH 32" MIN. ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES WITH FINISHED FLOOR / ICC A117.1-2009: 1 i