2235 LAKE HEIGHTS DR 2018 Plans 2022-11-22 (2)

• TIONS IN I RESISTANCE I T ASSEMBLIES I I T° JOINT I UL TESTED SYSTEMS: ; WALLS 714.4.1 THROUGH PENETRATIONS OF FIRE-RESISTANCE-RATED HORIZONTAL 715.1 JOINTS INSTALLED IN OR BETWEEN FIRE-RESISTANCE-RATED WALLS, FLOOR NOTE: ASSEMBLIES SHALL COMPLY WITH SECTION 714.4.1.1 OR 714.4.1.2. OR FLOOR/CEILING ASSEMBLIES AND ROOFS OR ROOF/CEILING ASSEMBLIES THESE FIRESTOPPING DETAILS ARE REPRESENTATIVE OF TYPICAL SITUATIONS ONLY. FOR 714.3.1 THROUGH PENETRATIONS OF FIRE-RESISTANCE-RATED HORIZONTAL SHALL BE PROTECTED BY AN APPROVED FIRE-RESISTANT JOINT SYSTEM OTHER CONDITIONS REFER TO MATRIX OF UL TESTED SYSTEMS BELOW. IF CONDITION IS S ASSEMBLIES SHALL COMPLY WITH SECTION 714.3.1.1 OR 714.3.1.2. NOT COVERED IN THIS MATRIX, CONTACT MANUFACTURER FOR TESTED ASSEMBLY DESIGNED TO RESIST THE PASSAGE OF FIRE FOR A TIME PERIOD NOT LESS EXCEPTIONS: THAN THE REQUIRED FIRE-RESISTANCE RATING OF THE WALL, FLOOR OR ROOF RECOMMENDATION.THIS MATRIX IS BASED ON 3M SYSTEMS. EQUALS MAY BE SUBSTITUTED I EXCEPTIONS: WHERE THE PENETRATING ITEMS ARE STEEL, FERROUS OR ONLY AFTER APPROVAL BY ARCHITECT.ALL FIRESTOP DETAILS TO BE EXECUTED BYCOPPER PIPES, TUBES OR CONDUITS,THE ANNULAR SPACE BETWEEN THE IN OR BETWEEN WHICH THE SYSTEM IS INSTALLED. FIRE-RESISTANT JOINT rPENETRATING ITEM AND THE FIRE-RESISTANCE-RATED WALL IS PERMITTED TO 1. PENETRATIONS BY STEEL, FERROUS OR COPPER CONDUITS, PIPES, SYSTEMS SHALL BE TESTED IN ACCORDANCE WITH SECTION 715.3. LICENSED AND/OR CERTIFIED INSTALLER. 1 BE PROTECTED AS FOLLOWS: TUBES OR VENTS OR CONCRETE OR MASONRY ITEMS THROUGH A 1928 43rd Ave E., Ste A SINGLE FIRE-RESISTANCE-RATED FLOOR ASSEMBLY WHERE THE EXCEPTIONS:ANNULAR SPACE IS PROTECTED WITH MATERIALS THAT PREVENT THE PENETRATING ITEM GYPSUM WOOD FLOOR/CEILING CONCRETE Seattle , W 2 0 6 A 9 8 1 1 2 2. THE MATERIAL USED TO FILL THE ANNULAR SPACE SHALL PREVENT ( ) 4 5 3A• En 5 3 2 PASSAGE OF FLAME AND HOT GASES SUFFICIENT TO IGNITE COTTON 1. FLOORS WITHIN A SINGLE DWELLING UNIT. THE PASSAGE OF FLAME AND HOT GASES SUFFICIENT TO IGNITE COTTON WL2002(FS195/RC 1,PPD) FC2002(FS195/RC-1,PPD) CAJ 2029 FA2002 s h o e s m i t h c o x. c o m WASTE WHEN SUBJECTED TO ASTM E119 OR UL 263 TIME-TEMPERATURE WASTE WHEN SUBJECTED TO ASTM E119 OR UL 263 TIME-TEMPERATURE 2. FLOORS WHERE THE JOINT IS PROTECTED BY A SHAFT ENCLOSURE IN PLASTIC WL2003(FS195/CP 25WB) FC2007(FS195/RC-1,PPD) CAJ 2001 FA 2027 FIRE CONDITIONS UNDER A MINIMUM POSITIVE PRESSURE DIFFERENTIAL ACCORDANCE WITH SECTION 713. WL2004 FS195/CP 25WB) FC2008(FS1951RC 1,PPD) CAJ 2117 WJ 2029 0.01 INCH CONDITIONS OF WATER AT THE LOCAITON OF THE PENETRATION FOR DIFFERENTIAL FIRE UNDER A MINIMUM POSITIVE PRESSUREOF 0.01 INCH (2.49 PA)OF WATER AT THE LOCATION OF THE 3. FLOORS WITHIN ATRIUMS WHERE THE SPACE ADJACENT TO THE ATRIUM OFWL2005 FS1951RC-1,PPD) CAJ 2021 THE TIME PERIOD EQUIVALENT TO THE FIRE-RESISTANCE RATING OF THE PENETRATION FOR THE TIME PERIOD EQUIVALENT TO THE IS INCLUDED IN THE VOLUME OF THE ATRIUM FOR SMOKE CONTROL WL2031 CS195/FS/195) CAJ 2027 FIRE-RESISTANCE RATING OF THE CONSTRUCTION PENETRATED. PURPOSES. WL2032 CP 25WB) CAJ 2040 CONSTRUCTION PENETRATED. PENETRATING ITEMS WITH A MAXIMUM 6-INCH (152 MM)NOMINAL 4. FLOORS WITHIN MALLS. WL2003 FS195/CP 25WB) CAJ 2132 714.3.1.1 FIRE-RATED-RESISTANCE ASSEMBLIES-PENETRATIONS SHALL BE DIAMETER SHALL NOT BE LIMITED TO THE PENETRATION OF A SINGLE 5. FLOORS AND RAMPS WITHIN OPEN AND ENCLOSED PARKING GARAGES METAL PIPE WL1001 (CP 25) FC1002(CP 25N/S,SIL) CAJ 1001 CAJ 1006 FIRE-RESISTANCE-RATED FLOOR ASSEMBLY, PROVIDED THE OR STRUCTURES CONSTRUCTED IN ACCORDANCE WITH SECTIONS 406.5 INSTALLED AS TESTED IN AN APPROVED FIRE-RESISTANCE-RATED WL1002 CP 25) FC1003 2000) CAJ 1044 CAJ 1065 ASSEMBLY. AGGREGATE AREA OF THE OPENINGS THROUGH THE ASSEMBLY DOES AND 406.6, RESPECTIVELY. WL1010(2000) FC1006(CP 25WB) CAJ 1112 CAJ 1092 NOT EXCEED 144 SQUARE INCHES (92 900 MM2) IN ANY 100 SQUARE FEET 6. MEZZANINE FLOORS. WL1016 CP 25WB) CAJ 1176 CAJ 1021 714.3.1.2 THROUGH-PENETRATION FIRESTOP SYSTEM-TROUGH (9.3 M2)OF FLOOR AREA. 7. WALLS THAT ARE PERMITTED TO HAVE UNPROTECTED OPENINGS. WL1017 CP 25N/S,S/L) CAJ 1017 PENETRATIONS SHALL BE PROTECTED BY AN APPROVED 2. PENETRATIONS IN A SINGLE CONCRETE FLOOR BY STEEL, FERROUS OR 8. ROOFS WHERE OPENINGS ARE PERMITTED. WL1032 CP 25 CAULKS) CAJ 1216 PENETRATION FIRESTOP SYSTEM INSTALLED AS TESTED IN COPPER CONDUITS, PIPES,TUBES OR VENTS WITH A MAXIMUM 6-INCH 9. CONTROL JOINTS NOT EXCEEDING A MAXIMUM WIDTH OF 0.625 INCH (15.9 WL1036 FD150) WL1037(CS195/FS195, CAJ 1225 ACCORDANCE WITH ASTM E814 OR UL 1479,WITH A MINIMUM (152 MM)NOMINAL DIAMETER, PROVIDED THE CONCRETE, GROUT OR MM)AND TESTED IN ACCORDANCE WITH ASTM E119 OR UL 263. CP 25WB) POSITIVE PRESSURE DIFFERENTIAL OF 0.01 INCH (2.49 PA)OF MORTAR IS INSTALLED THE FULL THICKNESS OF THE FLOOR OR THE WATER AND SHALL HAVE AN F RATING OF NOT LESS THAN THE THICKNESS REQUIRED TO MAINTAIN THE FIRE-RESISTANCE RATING.THE 715.2 A FIRE-RESISTANT JOINT SYSTEM SHALL BE SECURELY INSTALLED IN PENETRATING ITEMS SHALL NOT BE LIMITED TO THE PENETRATION OF A ACCORDANCE WITH THE LISTING CRITERIA IN OR ON THE JOINT FOR ITS ENTIRE INSULATED METAL PIPE WL5001 (FS195/CP 25) FC5002(FS195/CP 25WB) CAJ 5005 REQUIRED FIRE-RESISTANCE RATING OF THE WALL PENETRATED. SINGLE CONCRETE FLOOR, PROVIDED THE AREA OF THE OPENING LENGTH SO AS NOT TO DISLODGE, LOOSEN OR OTHERWISE IMPAIR ITS ABILITY WL5002(FS195/CP 25 CAJ 5002 WL5009(FS195/CP 25WB) CAJ 5003 714.3.2 MEMBRANE PENETRATIONS SHALL COMPLY WITH SECTION 714.3.1.WHERE THROUGH EACH FLOOR DOES NOT EXCEED 144 SQUARE INCHES(92 900 TO ACCOMMODATE EXPECTED BUILDING MOVEMENTS AND TO RESIST THE WL5010 FS195/CP 25WB) CAJ 5001 WALLS OR PARTITIONS ARE REQUIRED TO HAVE A FIRE-RESISTANCE RATING, MM2). PASSAGE OF FIRE AND HOT GASES. WL5011 CP 25WB) CAJ 5009 RECESSED FIXTURES SHALL BE INSTALLED SUCH THAT THE REQUIRED FIRE 3. PENETRATIONS BY LISTED ELECTRICAL BOXES OF ANY MATERIAL, WL5032 2000) CAJ 5017 RESISTANCE WILL NOT BE REDUCED.. PROVIDED SUCH BOXES HAVE BEEN TESTED FOR USE IN 715.3 FIRE-RESISTANT JOINT SYSTEMS SHALL BE TESTED IN ACCORDANCE WITH THE FIRE-RESISTANCE-RATED ASSEMBLIES AND INSTALLED IN ACCORDANCE REQUIREMENTS OF EITHER ASTM E1966 OR UL 2079. NONSYMMETRICAL WALL INSULATED CABLE WL2032(FS195/CS195/ FC3001 (CP 25N/S,S/L) CAJ 3030 CAJ 3111 1. MEMBRANE PENETRATIONS OF MAXIMUM 2-HOUR WITH THE INSTRUCTIONS INCLUDED IN THE LISTING. JOINT SYSTEMS SHALL BE TESTED WITH BOTH FACES EXPOSED TO THE CP 25WB) FC3002(2000/2003) CAJ 3080 CAJ 2029 FIRE-RESISTANCE-RATED WALLS AND PARTITIONS BY STEEL FURNACE,AND THE ASSIGNED FIRE-RESISTANCE RATING SHALL BE THE WL2033(FS195/CP 25WB/ FC3007 CP 25WB) CAJ 3021 CAJ 3005 !� ELECTRICAL BOXES THAT DO NOT EXCEED 16 SQUARE INCHES(0.0 103 714.4.1.1 THROUGH PENETRATIONS SHALL BE INSTALLED AS TESTED IN THE SHORTEST DURATION OBTAINED FROM THE TWO TESTS.WHERE EVIDENCE IS PUTTY) FC3008(FS195) CAJ 3014 CAJ 3004 �I 11.. M2) IN AREA, PROVIDED THE AGGREGATE AREA OF THE OPENINGS APPROVED FIRE-RESISTANCE-RATED ASSEMBLY. FURNISHED TO SHOW THAT THE WALL WAS TESTED WITH THE LEAST WL3002 2000) CAJ 3015 WL3008 2000) CAJ 3107 THROUGH THE MEMBRANE DOES NOT EXCEED 100 SQUARE INCHES FIRE-RESISTANT SIDE EXPOSED TO THE FURNACE, SUBJECT TO ACCEPTANCE WL3015 CP 25N/S) CAJ 3108 skilled nursin (0.0645 M2) IN ANY 100 SQUARE FEET(9.29 M2)OF WALL AREA.THE 714.4.1.2 THROUGH PENETRATIONS SHALL BE PROTECTED BY AN APPROVED OF THE BUILDING OFFICIAL, THE WALL NEED NOT BE SUBJECTED TO TESTS WL3030 FS195/CP 25WB) CAJ 3110 �` ANNULAR SPACE BETWEEN THE WALL MEMBRANE AND THE BOX THROUGH-PENETRATION FIRESTOP SYSTEM INSTALLED AND FROM THE OPPOSITE SIDE. WL3031 PUTTY) SHALL NOT EXCEED 1/8 INCH (3.2 MM). SUCH BOXES ON OPPOSITE TESTED IN ACCORDANCE WITH ASTM E814 OR UL 1479,WITH A WL3032 CP25 CAULKS) SIDES OF THE WALL OR PARTITION SHALL BE SEPARATED BY ONE OF MINIMUM POSITIVE PRESSURE DIFFERENTIAL OF 0.01 INCH OF EXCEPTION: FOR EXTERIOR WALLS WITH A HORIZONTAL FIRE SEPARATION MIXED PENETRATION ITEMS WL5001 (FS195/CS195/ N/A N/A THE FOLLOWING. WATER(2.49 PA).THE SYSTEM SHALL HAVE AN F RATING/T DISTANCE GREATER THAN 5 FEET(1524 MM),THE JOINT SYSTEM SHALL BE CP 25WB) RATING OF NOT LESS THAN 1 HOUR BUT NOT LESS THAN THE REQUIRED TO BE TESTED FOR INTERIOR FIRE EXPOSURE ONLY. 2235 Lake Heights Drive 1.1. BY A HORIZONTAL DISTANCE OF NOT LESS THAN 24 INCHES(610 REQUIRED RATING OF THE FLOOR PENETRATED. HVAC DUCTS WL708(CP 25WB) N/A CAJ 7003 MM)WHERE THE WALL OR PARTITION IS CONSTRUCTED WITH INDIVIDUAL CAJ 7016 715.E FIRE-RESISTANT JOINT SYSTEMS IN SMOKE BARRIERS,AND JOINTS AT THE NON-COMMUNICATING STUD CAVITIES; EXCEPTIONS: INTERSECTION OF A HORIZONTAL SMOKE BARRIER AND AN EXTERIOR CURTAIN Everett, WA 98208 1.2. BY A HORIZONTAL DISTANCE OF NOT LESS THAN THE DEPTH OF WALL, SHALL BE TESTED IN ACCORDANCE WITH THE REQUIREMENTS OF UL THE WALL CAVITY WHERE THE WALL CAVITY IS FILLED WITH CELLULOSE 1. FLOOR PENETRATIONS CONTAINED AND LOCATED WITHIN 2079 FOR AIR LEAKAGE.THE L RATING OF THE JOINT SYSTEM SHALL NOT ^� LOOSEFILL, ROCKWOOL OR SLAG MINERAL WOOL INSULATION; THE CAVITY OF A WALL ABOVE THE FLOOR OR BELOW THE EXCEED 5 CFM PER LINEAR FOOT(0.00775 M3/S M)OF JOINT AT 0.30 INCH (7.47 FIRESTOPPING I 1.3. BY SOLID FIREBLOCKING IN ACCORDANCE WITH SECTION 718.2.1; FLOOR DO NOT REQUIRE A T RATING. PA)OF WATER FOR BOTH THE AMBIENT TEMPERATURE AND ELEVATEDA CONSTRUCTION 1.4.OR BY PROTECTING BOTH OUTLET BOXES WITH LISTED PUTTY PADS; 2. FLOOR SHOWER DRAINPENETRATIONS CONTAINED AND LOCATINS,TUB ED WITHIN RTHES OR 0 TEMPERATURE TESTS. VOIDSINV TI 1.5. BY OTHER LISTED MATERIALS AND METHODS. CONCEALED SPACE OF A HORIZONTAL ASSEMBLY DO NOT REQUIRE A T RATING. 2. MEMBRANE PENETRATIONS BY LISTED ELECTRICAL BOXES OF ANY 3. FLOOR PENETRATIONS OF MAXIMUM 4-INCH (102MM) MATERIAL, PROVIDED SUCH BOXES HAVE BEEN TESTED FOR USE IN NOMINAL DIAMETER PENETRATING DIRECTLY INTO FIRE-RESISTANCE-RATED ASSEMBLIES AND ARE INSTALLED IN METAL-ENCLOSED ELECTRICAL POWER SWITCHGEAR DO NOT ACCORDANCE WITH THE INSTRUCTIONS INCLUDED IN THE LISTING.THE REQUIRE A T RATING. ANNULAR SPACE BETWEEN THE WALL MEMBRANE AND THE BOX SHALL NOT EXCEED 1/8 INCH (3.2 MM) UNLESS LISTED OTHERWISE. SUCH BOXES 714.4.2 MEMBRANE PENETRATIONS my ON OPPOSITE SIDES OF THE WALL OR PARTITION SHALL BE SEPARATED PENETRATIONS OF MEMBRANES THAT ARE PART OF A HORIZONTAL ASSEMBLY 4.0'` m► BY ONE OF THE FOLLOWING: SHALL COMPLY WITH SECTION 714.4.1.1 OR 714.4.1.2.WHERE FLOOR/CEILING ASSEMBLIES ARE REQUIRED TO HAVE A FIRE-RESISTANCE RATING, RECESSED r 2.1 BY THE HORIZONTAL DISTANCE SPECIFIED IN THE LISTING OF THE FIXTURES SHALL BE INSTALLED SUCH THAT THE REQUIRED FIRE RESISTANCE - of the Nothwest ELECTRICAL BOXES; WILL NOT BE REDUCED. RATED PARTITION CONDUIT 2.2 BY SOLID FIREBLOCKING IN ACCORDANCE WITH SECTION 718.2.1; SEE PLAN No. DATE REVISION 2.3 BY PROTECTING BOTH BOXES WITH LISTED PUTTY PADS; OR EXCEPTIONS: • 2.4 BY OTHER LISTED MATERIALS AND METHODS. 1. MEMBRANE PENETRATIONS BY STEEL, FERROUS OR COPPER CONDUITS, - - OUTLET BOX CITY RESPONSE#1 PIPES TUBES OR VENTS, OR CONCRETE OR MASONRY ITEMS WHERE A°3292o19 3. MEMBRANE PENETRATIONS BY ELECTRICAL BOXES OF ANY SIZE OR THE ANNULAR SPACE IS PROTECTED EITHER IN ACCORDANCE WITH SHOWN DASHED I TYPE,THAT HAVE BEEN LISTED AS PART OF A WALL OPENING A05.30.2019 CITY RESPONSE#2 PROTECTIVE MATERIAL SYSTEM FOR USE IN FIRE-RESISTANCE-RATED SECTION 714.4.1 OR TO PREVENT THE FREE PASSAGE OF FLAME AND THE ASSEMBLIES AND ARE INSTALLED IN ACCORDANCE WITH THE PRODUCTS OF COMBUSTION.THE AGGREGATE AREA OF THE OPENINGS INSTRUCTIONS INCLUDED IN THE LISTING. THROUGH THE MEMBRANE SHALL NOT EXCEED 100 SQUARE INCHES (64 _ _ _ J 500 MM2) IN ANY 100 SQUARE FEET(9.3 M2)OF CEILING AREA IN • . 4. MEMBRANE PENETRATIONS BY BOXES OTHER THAN ELECTRICAL ASSEMBLIES TESTED WITHOUT PENETRATIONS. ' BOXES, PROVIDED SUCH PENETRATING ITEMS AND THE ANNULAR SPACE 2. CEILING MEMBRANE PENETRATIONS OF MAXIMUM 2-HOUR HORIZONTAL BETWEEN THE WALL MEMBRANE AND THE BOX,ARE PROTECTED BY AN ASSEMBLIES BY STEEL ELECTRICAL BOXES THAT DO NOT EXCEED 16 MOLDED PUTTY • APPROVED MEMBRANE PENETRATION FIRESTOP SYSTEM INSTALLED AS SQUARE INCHES (10 323 MM2) IN AREA, PROVIDED THE AGGREGATE FIRE BARRIER TESTED IN ACCORDANCE WITH ASTM E814 OR UL 1479,WITH A MINIMUM AREA OF SUCH PENETRATIONS DOES NOT EXCEED 100 SQUARE INCHES AROUND EXPOSED ti POSITIVE PRESSURE DIFFERENTIAL OF 0.01 INCH (2.49 PA)OF WATER, (44 500 MM2) IN ANY 100 SQUARE FEET(9.29 M2)OF CEILING AREA,AND FACES OF AND SHALL HAVE AN F AND T RATING OF NOT LESS THAN THE REQUIRED THE ANNULAR SPACE BETWEEN THE CEILING MEMBRANE AND THE BOX OUTLET BOX ANSI UL263 FIRE TESTS FIRE-RESISTANCE RATING OF THE WALL PENETRATED AND BE INSTALLED DOES NOT EXCEED 1/8 INCH (3.2 MM). IN ACCORDANCE WITH THEIR LISTING. 3. MEMBRANE PENETRATIONS BY ELECTRICAL BOXES OF ANY SIZE OR OF BLD'G. CONST. MATERIALS TYPE, THAT HAVE BEEN LISTED AS PART OF AN OPENING PROTECTIVE TYP.SYSTEM FOR USE IN HORIZONTAL ASSEMBLIES AND ARE A FIRESTOP PROJECT MANAGER 5.THE ANNULAR SPACE CREATED BY THE PENETRATION OF ANco AUTOMATIC SPRINKLER, PROVIDED IT IS COVERED BY A METAL /5\ INSTALLED IN ACCORDANCE WITH THE INSTRUCTIONS INCLUDED IN THE 3 -_ 1-0 JS ESCUTCHEON PLATE. LISTING. PROJECT ARCHITECT 4. MEMBRANE PENETRATIONS BY LISTED ELECTRICAL BOXES OF ANY THROUGH PENETRATION FIRE JS 6. MEMBRANE PENETRATIONS OF MAXIMUM 2-HOUR FIRE MATERIAL, PROVIDED SUCH BOXES HAVE BEEN TESTED FOR USE IN STOP. INSTALL PER UL LISTING PROJECT TEAM MEMBERS FIRE-RESISTANCE-RATED ASSEMBLIES AND ARE INSTALLED IN W-L-2088 FOR PIPES 2" OR RESISTANCE-RATED WALLS AND PARTITIONS BY STEEL ELECTRICAL ��-�� ._ 1 -HR. OR 2-HR. ASSEMBLY TS BOXES THAT EXCEED 16 SQUARE INCHES (0.0 103 M2) IN AREA, OR STEEL ACCORDANCE WITH THE INSTRUCTIONS INCLUDED IN THE LISTING.THE LESS. FOR PIPES 4 OR LESS ELECTRICAL BOXES OF ANY SIZE HAVING AN AGGREGATE AREA ANNULAR SPACE BETWEEN THE CEILING MEMBRANE AND THE BOX MAX. FOUR COPPER CONDUCTOR INSTALL PER UL LISTING CHECK THROUGH THE MEMBRANE EXCEEDING 100 SQUARE INCHES(0.0645 M2) SHALL NOT EXCEED 1/8 INCH (3.2 MM)UNLESS LISTED OTHERWISE. NO.2 AWG ARMORED CABLE OR �� W-L-2147 IN ANY 100 SQUARE FEET(9.29 M2)OF WALL AREA, PROVIDED SUCH 5. THE ANNULAR SPACE CREATED BY THE PENETRATION OF A FIRE SINGLE METAL-CLAD CABLE 111111 PENETRATING ITEMS ARE PROTECTED BY LISTED PUTTY PADS OR OTHER SPRINKLER, PROVIDED IT IS COVERED BY A METAL ESCUTCHEON PLAT:. LISTED MATERIALS AND METHODS,AND INSTALLED IN ACCORDANCE 6. ELNONCOMBUSTIBLE ITEMS THAT ARE CAST EMENTS AND THAT DO NOT PENETRATEIBOTOH TONCRETE OP AND BOTTOM BUILDING ,� � I, ��` �II , ,.,,,,.... WITH THE LISTING. ARCHITECT SEAL SURFACES OF THE ELEMENT. f- ,� . ,,, ,410,, 1 7. THE CEILING MEMBRANE OF 1-AND 2-HOUR FIRE-RESISTANCE-RATEDli 7534 HORIZONTAL ASSEMBLIES IS PERMITTED TO BE INTERRUPTED WITH TH THROUGH PENETRATION FIRES �I . 1 -HR. OR 2-HR. ASSEMBLY REGISTERED DOUBLE WOOD TOP PLATE OF A WALL ASSEMBLY THAT IS SHEATHED .� STOP. INSTALL PER UL LISTING II_______ I'I ARCHITECT WITH TYPE X GYPSUM WALLBOARD, PROVIDED THAT ALL PENETRATING I W-L-3015 ITEMS THROUGH THE DOUBLE TOP PLATES ARE PROTECTED IN --_`_ ACCORDANCE WITH SECTION 714.4.1.1 OR 714.4.1.2 AND THE CEILING MEMBRANE IS TIGHT TO THE TOP PLATES. MIN. 1" MINERAL WOOL II JOHN A. SHOESMITH 714.4.4 PENETRATIONS IN SMOKE BARRIERS SHALL BE PROTECTED BY AN APPROVED INSULATION �0"- 1 1 -HR. OR 2-HR. ASSEMBLY STATE OF WASHINGTON THROUGH-PENETRATION FIRESTOP SYSTEM INSTALLED AND TESTED IN THROUGH THROUGH PENETRATION FIRE ACCORDANCE WITH THE REQUIREMENTS OF UL 1479 FOR AIR LEAKAGE.THE L PENETRATION STOP. INSTALL PER UL LISTING RATING OF THE SYSTEM MEASURED AT 0.30 INCH(7.47 PA)OF WATER IN BOTH ti FIRE STOP. • " `'''"" H AMBIENT TEMPERATURE AND ELEVATED TEMPERATURE TESTS SHALL NOT W-L-2088 FOR PIPES 2" OR '`'' y:..j ', 'S f 4: THE INSTALL PER UL,��;�'��`�:..`:;=;� :��; ':� ,v>_:.;'- EXCEED: LISTING C3 LESS. FOR PIPES 4 OR LESS ,>E V I E.1AI it -+ i' h..:{::.R:11! W-L-3032 'V Y'.`' _ ,` INSTALL PER UL LISTING 1. 5.0 CFM PER SQUARE FOOT(0.025 M3/S• M2)OF PENETRATION OPENING u:a, W-L-2147 0 FOR EACH THROUGH-PENETRATION FIRESTOP SYSTEM; OR / _ , TITLE 0. (/'�'�� - PENETRATION 2.A TOTAL CUMULATIVE LEAKAGE OF 50 CFM (0.024 M3/S)FOR ANY 100 SQUA'E ,.;;: i'''` FEET(9.3 M2)OF WALL AREA, OR FLOOR AREA. - --_- .,.,..,, NOTES DETAILS -�° CABLES - AGGREGATE CROSS �� SECTION OF CABLES TO BE MIN 8 PERCENT AND MAX 36 PERCENT PROJECT NO. P OF CROSS SECTIONAL AREA C ,n mu 1" ,<<<:, 18.03-01 1 a DATE 12/21/2018 PROJECT NETWORK PATH STEEL SLEEVE -D --eel 1 -HR. OR 2-HR. ASSEMBLY 1 ill SHEET NUMBER T - A TIONS AT " * TED WALLS /" g T • A TI T' WALLS 1 3" = 1'-0° 3 = 10 COPYRIGHT©2019 shoesmith cox architects