Laserfiche WebLink
MATERIAL IDENTIFICATION <br />CONTINUOUS <br />U <br />PERIODIC <br />N <br />VERIFY TYPE AND GRADE OF MATERIAL. <br />WELDER IDENTIFICATION <br />CONTINUOUS <br />❑ <br />PERIODIC <br />Z <br />A SYSTEM SHALL BE MAINTAINED BY WHICH A <br />WELDER WHO HAS WELDED A JOINT OR <br />MEMBER CAN BE IDENTIFIED. <br />FIT -UP GROOVE WELDS <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY JOINT PREPARATION, DIMENSIONS, <br />CLEANLINESS, TACKING, AND BACKING <br />ACCESS HOLES <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY CONFIGURATION AND FINISH. <br />FIT -UP OF FILLET WELDS <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY ALIGNMENT, GAPS AT ROOT, <br />CLEANLINESS OF STEEL SURFACES, AND TACK <br />WELD QUALITY AND LOCATION. <br />ITEM <br />FREQUENCY OF INSPECTION <br />INSTRUCTIONS <br />USE OF QUALIFIED WELDERS <br />CONTINUOUS <br />❑ <br />PERIODIC <br />® <br />VERIFY THAT WELDERS ARE APPROPRIATELY <br />QUALIFIED. <br />CONTROL AND HANDLING OF WELDING <br />CONTINUOUS <br />❑ <br />PERIODIC <br />® <br />VERIFY PACKAGING AND EXPOSURE CONTROL. <br />CONSUMABLES <br />CRACKED TACK WELDS <br />CONTINUOUS <br />❑ <br />PERIODIC <br />❑ <br />VERIFY THAT WELDING DOES NOT OCCUR <br />OVER CRACKED TACK WELDS, <br />ENVIRONMENTAL CONDITIONS <br />CONTINUOUS <br />❑ <br />PERIODIC <br />® <br />VERIFY WIND SPEED IS WITHIN LIMITS AS WELL <br />AS PRECIPITATION AND TEMPERATURE. <br />WPS FOLLOWED <br />CONTINUOUS <br />❑ <br />PERIODIC <br />Z <br />VERIFY ITEMS SUCH AS SETTINGS ON WELDING <br />EQUIPMENT, TRAVEL SPEED, WELDING <br />MATERIALS, SHIELDING GAS TYPE/FLOW RATE, <br />REHEAT APPLIED, INTERPASS TEMPERATURE <br />MAINTAINED AND PROPER POSITION. <br />WELDING TECHNIQUES <br />CONTINUOUS <br />❑ <br />PERIODIC <br />Z <br />VERIFY INTERPASS AND FINAL CLEANING, EACH <br />PASS IS WITHIN PROFILE LIMITATIONS, AND <br />QUALITY OF EACH PASS. <br />K-AREA CONTINUOUS ❑ PERIODIC ❑ <br />BACKING & WELD TABS REMOVED CONTINUOUS ❑ PERIODIC ❑ <br />REPAIR ACTIVITIES CONTINUOUS ® PERIODIC ❑ <br />DOCUMENT ACCEPTANCE OR CONTINUOUS Z PERIODIC ❑ <br />REJECTION OF WELDED JOINT/MEMBER <br />SYM REVISION BY APPROVED DATE SYM REVISION <br />0 REVISION RELEASE 117 (IFC-PHW2) SLJ DPB 06/25/19 <br />NONDESTRUCTIVE <br />ITEM <br />FREQUENCY OF INSPECTION <br />INSTRUCTIONS <br />CJP WELDS (RISK CAT II) <br />CONTINUOUS ❑ <br />PERIODIC ZULTRASONIC <br />TESTING SHALL BE PERFORMED <br />ON 10% OF CJP GROOVE WELDS IN BUTT, T-AND <br />CORNER JOINTS SUBJECT TO TRANSVERSELY <br />APPLIED TENSION LOADING IN MATERIALS 5/16-INCH <br />THICK OR GREATER TESTING RATE MUST BE <br />INCREASED OF > 5% OF WELDS TESTED HAVE <br />UNACCEPTABLE DEFECTS. <br />ACCESS HOLES (FLANGE > 2") <br />CONTINUOUS ❑ <br />PERIODIC Z <br />TESTED PER AISC 360®10-5C. <br />WELDED JOINTS SUBJECT TO FATIGUE <br />CONTINUOUS Z <br />PERIODIC ❑ <br />PER RISC 360-10-51). <br />PRIORI ®®, AISC <br />ITEM <br />FREQUENCY OF INSPECTION <br />INSTRUCTIONS <br />CERTIFICATIONS OF FASTENERS <br />CONTINUOUS Z <br />PERIODIC ❑ <br />FASTENERS MARKED <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY THAT FASTENERS HAVE BEEN MARKED IN <br />ACCORDANCE WITH ASTM REQUIREMENTS. <br />PROPER FASTENERS FOR JOINT <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY GRADE, TYPE, AND BOLT LENGTH IF <br />THREADS ARE EXCLUDED FROM THE SHEAR <br />PLANE. <br />PROPER BOLTING PROCEDURE <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY PROPER PROCEDURE IS USED FOR THE <br />JOINT DETAIL. <br />CONNECTING ELEMENTS <br />CONTINUOUS ❑ <br />PERIODIC ® <br />VERIFY APPROPRIATE FRYING SURFACE <br />CONDITION AND HOLE PREPARATION, IF <br />SPECIFIED, MEET REQUIREMENTS. <br />PRE -INSTALLATION VERIFICATION <br />CONTINUOUS ❑ <br />PERIODIC Z <br />OBSERVE AND DOCUMENT VERIFICATION <br />TESTING <br />TESTING BY INSTALLATION PERSONNEL FOR <br />FASTENER ASSEMBLIES AND METHODS USED. <br />PROPER STORAGE <br />CONTINUOUS ] <br />PERIODIC <br />VERIFY PROPER STORAGE OF BOLTS, BUTS, <br />WASHERS, AND OTHER FASTENER <br />COMPONENTS. <br />NOT REQUIRED IF ONLY SNUG -TIGHT JOINTS ARE SPECIFIED (PER SECTION N5.6(1) OF RISC 360-10) <br />BOLTINGDURING o®9 AISC 360-10): <br />ITEM <br />FREQUENCY OF INSPECTION <br />INSTRUCTIONS <br />FASTENER ASSEMBLIES <br />CONTINUOUS ❑ <br />PERIODIC Z <br />VERIFY THAT FASTENER ASSEMBLIES ARE OF <br />SUITABLE CONDITION, PLACED IN ALL HOLES, <br />AND WASHERS ARE POSITIONED AS REQUIRED. <br />SNUG -TIGHT PRIOR TO PRETENSIONING CONTINUOUS ❑ PERIODIC ❑ VERIFY THAT JOINTS ARE BROUGHT TO SNUG - <br />TIGHT CONDITION PRIOR TO PRETENIONING <br />OPERATION. <br />FASTENER COMPONENT CONTINUOUS F❑ PERIODIC ® VERIFY THAT FASTENER COMPONENT IS NOT <br />TURNED BY WRENCH PREVENTED FROM <br />ROTATING. <br />_ $j01 mmjlj _r, moot all _ a <br />IN ACCORDANCE WITH RCSC SPECIFICATION, <br />PROGRESSING SYSTEMATICALLY FROM THE <br />MOST RIGID POINT TOWARD THE FREE EDGES. <br />NOT REQUIRED IF ONLY SNUG -TIGHT JOINTS ARE SPECIFIED (PER SECTION N5.6(1) OF RISC 360-10). <br />* NOT REQUIRED FOR PRETENSIONED JOINTS USING TURN -OF -THE -NUT METHOD WITH MATCH -MARKING, DIRECT - <br />TENSION -INDICATORS, OR TWIST -OFF TYPE TENSION CONTROL METHOD (PER SECTION N5.6(2) OF RISC 360-10). <br />ACCEPTABILITY MEM <br />THIS DESIGN AND/OR CHEC <br />SPECIFICATION IS APPROVED AHM <br />E GI' <br />APPROVED BY DEBT. I DATE DPB <br />I I lJOB N0. <br />::-ISTRUCTURAL MASTER EVERETT, WA DWG N0. <br />COMP NO. <br />40-058-S2c <br />on <br />