811 SE EVERETT MALL WAY OLYMPIC HOT TUB 2025-09-26

Interior Lighting - Building Area Method LTG-INT-BLD 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2,R3,R4 over 3 stories and all R Revised Nov 2017 Project Title: Olympic Hot Tub Retail Tenant Improvement Date 2/18/2021 Calculation 0 New Construction 0 Addition- O Addition For Building Department Use Area NOTE 9 stand alone +existing O Spaces where<50%of O Spaces where>-50%of O Spaces where the Use luminaires are replaced luminaires are replaced is changing(C505) LPA 0 Standard 0 Additional Efficiency Package Option O Calculation C406.3 Reduced Interior Lighting Power To comply with C406.3,the Proposed LPD shall be 25%lower than the Target LPA. I User Note Type Refer to C406.3 for additional requirements. Maximum Allowed Lighting Wattages'°TE Watts Allowed Location(plan#, Gross Interior Allowed 2 (watts/ft2 area) Building Area room#,or ALL) Area Description Area in ft2 Watts per ft2 NOTE 2 Office Al-1, 100-105 Restroom,storage,break area,and open office 634 0.66 419 Retail Al-1, 106-108 Water Care,Mood Room&Showroom 2997 1.01 3027 Total 3631 Proposed Lighting Wattage Location(plan#, Number of Watts per Building Area room#) Fixture Description NOTE 3,4,5,6 Fixtures Fixture NOTE 7 Watts Proposed Office A2-1, 100 ceiling mounted LED square light fixture 2 14 28 Office _ A2-1, 100 LED Vanity Wall Sconce 1 21 21 Office A2-1,102-105 2X2 recesssed LED light fixture 10 35 350 Retail A2-1, 106 2X2 recesssed LED light fixture 2 35 70 Retail A2-1, 107 LED track lighting 33 37 1221 Retail _ A2-1, 108 Recessed can lights 4 12 48 Retail A2-1, 108 LED Tape 88 3 264 Compliance by Building Area NOTE 8 Total Allowed Total Proposed Interior Lighting Building Area Warnings Watts Watts Power Allowance Set LPA Office 419 399 Calculation Type Confirm all fixtures are reported under proposed lighting-low watts Set LPA Retail 3027 1603 Calculation relative to maximum allowed. Type Note 1-List all unique building areas per Table C405.4.2(1)that occur in the Totals 3446 2002 project scope.Select building area category from drop down menu. Note 2-Unlit Message-Enter lighting fixture information for this building area surface in Proposed Lighting Wattage table to generate Lighting Power Allowance. Note 3-Proposed fixtures must be listed in the building area in which they occur.List all proposed lighting fixtures including exempt lighting equipment and existing-to-remain fixtures. Note 4-For proposed Fixture Description,indicate fixture type,lamp type(e.g. T-8),number of lamps in the fixture,and ballast type(if included). For track lighting,list the length of the track(in feet)in addition to the fixture,lamp,and ballast information. Note 5-For lighting equipment eligible for exemption per C405.4.1,note exception number and leave Watts/Fixture blank. Note 6-Existing-to-remain fixtures shall be included in the Proposed Lighting Wattage table in the same manner as new fixtures.Identify as existing in fixture description. Note 7-For proposed Watts/Fixture enter the luminaire wattage for installed lamp and ballast using manufacturer or other approved source.For luminaires with screw-in lamps,enter the manufacturer's listed maximum input wattage of the fixture(not the lamp wattage).For low voltage lighting,enter the wattage of the transformer. For line voltage track/busway systems,enter the larger of the attached luminaire wattage or 50 watts/lineal foot,or enter the wattage limit of permanent current limiting device. 3 � Note 8-Proposed Wattage for each Building Area type shall not exceed the Allowed Wattage for that Building Area type. Trading wattage ti..ti...,...,o..:w:.... n...,,s........:....s,.n........�........�sa.,o..a.r......n.....,e�..ati...�.........r.......,..,,.ati