Laserfiche WebLink
; i f • • • ► ' • 4 ' — ' 611 '" ' ' 5 6 • A • ' <br /> 2018 WSEC Requirements for Commercial B .s including Group R2,R3&R4 over 3 stories&all R1 •dministered by©2021 NEEA,All rights reserved <br /> The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State <br /> Energy Code,Commercial Provisions. <br /> For questions about this report,contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com <br /> C402.2.6 ;Slab-on-grade floor !Indicate'R-salue of continuous insulation on <br /> ' .03 2.1 insulation ; <br /> C wall section or foundation detail-1 <br /> i <br /> C402.2.6 1 Slab-on-grade floor Indicate insulation extends down vertically <br /> C303.2.1 insulation and/or horizontally the required distance from <br /> top of slab4 <br /> C402.2.6 i Slab-on-grade floor Indicate method of protection of exposed <br /> C303.2.1 insulation exterior slab edge insulation4 <br /> C402.2.6 Heated slab-on-grade Indicate R-value of continuous insulation on <br /> C303.2.1 : floor insulation wall section or foundation detail4 <br /> C402.2.6 tkatcd slab-on wade j Indicate insulation extends down vertically <br /> C303.2.1 =floor insulation from top€=i slab and then horizontally under <br /> the entire slab4 <br /> C402.2.6 . Heated slab-on-grade Indicate method of protection of exposed <br /> C303.2.1 floor insulation exterior slab edge insulation4 <br /> C'40'y.2.8 Radiant heatino Indicate insulation R value behind radiant , <br /> system insulation panels.U-bendlheaders and bottom surface of <br /> radiantly heated floors(other than heated slab- <br /> on-grade)4. <br /> (.402.4,1 i Vertical fenestration Provide total gross sf area of all above grade - <br /> C 502,2.1 .iaximurn area wall elements and rough opening sf area of all ; <br /> vertical fcttestr tion elements in the building, <br /> for the prescriptive max allowed window-to- <br /> ttallratio(WWR)calculation in the WSEC <br /> envelope compliance reports;demonstrate <br /> compliance for each space conditioning <br /> ' . category sefarately4 <br /> Increased prescriptive • Provide calculations showing that not <br /> C402.4.1.1 = P P less. that <br /> C40�2,4.1 ; maximum vertical 5tY% of the total conditioned floor area is <br /> C502.2.1 fenestration area with within a daylight zone;demonstrate <br /> daylight zones and compliance for each space conditioning <br /> i controls cutegoryPse�atel 4 <br /> i <br /> i C402.4.1.1 Increased prescriptive Indicate in envelope plans that all lighting • <br /> • <br /> C405.2.4.1 maximum vertical fixtures located within daylight zones shall be <br /> C502.2.1 fenestration area with ; provided with daylight responsive controls per <br /> daylight zones a`nd Section C405.2.4.14 <br /> controls <br /> C402.4.1.1 Increased prescriptive i Indicate that the VT of vertical fenestration is <br /> • <br /> C405.2.4.1 'maximum vertical at least 1.1 times the rated SHGC or no less <br /> C502.2.1 i fenestration area with than VT-0.55,whichever is greater4 <br /> daylight zones and <br /> controls <br /> 'C402.4,1.3 increased prescriptive Indicate" high performance tl factors and - <br /> 001.2.1 ttiax.inium vertical cvliGC values in fenestration schedules-1 <br /> fenestration area with <br /> high-performance <br /> iiancc <br /> giv ing:, <br /> C402.4.1.3 Increased prescriptive i Indicate if an area-weighted U-factor is used <br /> C502.2.1 maximum vertical for multiple fenestration elements within the <br /> I fenestration area with ! same fenestration category per Table C402.4; <br /> high-performance provide area-weighted U-factor calculation4 <br /> glazing <br /> • <br /> *Page4/9- <br />