1916 HOYT AVE 2021-12-22 - Laserfiche WebLink

RESIDENIIL PHOTOVOLTAIC PERMITOPLICATION (Page 2 of 2) 477 CITY OF EVERETT PERMIT SERVICES 3200 CEDAR STREET, EVERETT, WA 98201 (P)425-257-8810 I FAX 425-257-8857 I (E)everetteps@everettwa.gov I www.everettwa.govlpermits ELECTRICAL PERMIT CHECKLIST 411/ DETERMINE IF YOUR PROJECT QUALIFIES FOR AN OVER-THE-COUNTER ELECTRICAL PERMIT: If you answer yes to all of the below questions, the project qualifies for an over-the-counter electrical permit. YES NO 1. PV modules, inverters, and combiner boxes are identified for use in PV systems. ® ❑ 2. The inverters are listed and laveled in accordance with UL 1741 and are listed for utility interaction. [IRC M2302.4] [3 ❑ 3. The AC interconnection point is on the load side of service disconnect. [NEC 690.64(B)] IA ❑ 4. The system meets all current NEC, City, and Washington Cities Electrical Code requirements. 15a ❑ 5. For Split-Buss modules the AC interconnection must be one of the six service disconnects. [ ❑ 6. Maximum load added to the panel board is vased on the rating of the panelboards bus/main OCPD combination in accordance with NEC 705.12(D)(2)(3)(b), and is limited to (check the combination below that applies): ❑ 225amp bus/200amp main OCPD-13,400AC watts, max. 70amp inverter OCPD. 0225amp bus/225amp main OCPD-8,640AC watts, max.45amp inverter OCPD. ❑ 200amp bus/200amp main OCPD-7,860AC watts, max.40amp inverter OCPD. ❑ 150amp bus/150amp main OCPD-5,760AC watts, max. 30amp inverter OCPD. ❑ 125amp bus/125amp main OCPD-4,800AC watts, max. 25amp inverter OCPD. ❑ 125amp bus/100amp main OCPD-9,600AC watts, max. 50amp inverter OCPD. ❑ 100amp bus/100amp main OCPD-3,840AC watts, max.20amp inverter OCPD. ❑ Other Electrical Permit with Plan Review Required: note 1: Listed un-aiterea factory malnidus combination. /Iteration of the panel oars main UC:F'U will require plan raview Note 2: The circuit conductors and overcurrent devices shall be sized to carry not less than 125 percent of the • maximum currents as calculated in 690.8(A).The rating or setting of overcurrent devices shall be permitted in accordance with 240.4(B) and (C). [NEC 690.8(B)(1)] Note 3: If a panelboard employs a snap switch rated 30 amperes or less in any branch circuit, it cannot be rated more than 200 amperes unless there is a supply side overcurrent protection at 200 amperes or less within the panelboard. This requirement does not apply to panelboards equipped with circuit breakers. Section 408.36(a)of the NEC. 7. I have attached the following Electrical One-Line Diagram: ❑ Standard Electrical Diagram -6 Strings or Less ja Standard Electrical Diagram -4 Strings or Less ;0-- tandard Electrical Diagram - Micro Inverter ❑ None of the above- Electrical Permit with Plan Review Required PLEASE FILL OUT A CITY OF EVERETT ELECTRICAL PERMIT APPLICATION IF YOU QUALIFY FOR AN OTC ELECTRICAL PERMIT. AGREEMENT: I hereby certify that I have read and examined this application and know the same to be true and correct. All provisions of laws and ordinances governing this type of work will be completed whether specified herein or not. The granting of a permit does not presume to give authority to violate or cancel the provisions of any other state or local law regulating construction or the performance of construction. That I am authorized by the owner of this property to perform the work for which application is made and I comply with the State Contractors Law 18.27 RCW and 296.200 WAC. City of Everett Official Use Only ASSOCIATED ELECTRICAL PERMIT# f �g E 13I I -ocj • Ow thoriz ent Signature Date (Revised 9/30/2016)