3500 TERMINAL AVE 2017 Plans 2022-11-22 (2)

J'.ItAl NOTES: ASBESTOS —CONTAINING riATERli'ai_:> 1. THIS PROJECT INCLUDES REMOVAL AND DISPOSAL OF HAZARDOUS BUILDING MATERIALS (ASBESTOS, LEAD —CONTAINING PAINT (LCP), POLYCHLORINATED BIPHENYLS (PCB), AND MERCURY —CONTAINING LIGHT TUBES & HID BULBS) FROM THE PORT OF EVERETT SOUTH TERMINAL WHARF BUILDING T-5 LOCATED IN EVERETT, WA. 2. LOCATIONS OF ASSUMED ASBESTOS —CONTAINING MATERIALS (ACM) SHOWN ON THE DRAWINGS ARE SCHEMATIC AND APPROXIMATE. NOTE: A LIMITED HAZARDOUS MATERIALS SURVEY WAS ACCOMPLISHED IN PREPARATION FOR THE WORK, THAT MEETS THE REQUIREMENTS OF WASHINGTON STATE DEPARTMENT OF LABOR AND INDUSTRIES DIVISION OF OCCUPATIONAL SAFETY AND HEALTH (L&I DOSH) 99GOOD FAITH INSPECTION" AND PUGET SOUND CLEAN AIR AGENCY'S (PSCAA) ASBESTOS INSPECTION TO LOCATE AND IDENTIFY ACM EXPECTED TO BE IMPACTED BY THE PROJECT (INCLUDED AS APPENDIX OF SECTION 01 1.1 1.0 SUMMARY OF HAZARDOUS MATERIALS). ALL IMPACTED ACM WILL BE REMOVED WITHIN THE SCOPE OF THIS PROJECT. DEMOLITION FOR ACCESS TO CONCEALED ACM AND/OR ASSUMED ACM IS WITHIN THE SCOPE OF WORK. IF ANY IDENTIFIED ACM, OR SUSPECT MATERIAL NOT ADDRESSED BY THE "GOOD FAITH SURVEY" WILL BE IMPACTED AND IS NOT CALLED —OUT BY OTHER WORK AND IS NOT CALLED --OUT FOR REMOVAL, CONSULT THE PORT'S HAZARDOUS MATERIALS CONSULTANT (EHSI) PRIOR TO DISTURBANCE. ANY SUCH MATERIAL MUST BE TREATED AS ACM UNLESS SAMPLED BY A CERTIFIED AHERA BUILDING INSPECTOR AND DETERMINED TO BE NON ---ASBESTOS. 3. USE THE PROJECT HAZARDOUS MATERIALS SUMMARY LISTED ON THIS SHEET FOR BASE BID QUANTITIES. QUANTITIES ARE CONSIDERED ACCURATE WITHIN PLUS OR MINUS (+/—) TEN PERCENT (10%). NO CONTRACT CHANGES WILL BE CONSIDERED FOR VARIANCES IN THESE QUANTITIES OF LESS THAN 10%. CONTRACTOR MUST HAVE HAZARDOUS MATERIALS CONSULTANT'S. WRITTEN VERIFICATION OF QUANTITIES PRIOR TO THE REMOVAL OF MATERIALS FOR CONSIDERATION OF COMPENSATION FOR ADDITIONAL QUANTITIES OF MATERIAL IN EXCESS OF +10%. 4o THE CONTRACTOR SHALL FIELD VERIFY AND COORDINATE WITH DEMOLITION PLANS, DETAILS, AND DIMENSIONS THAT MAY IMPACT THE WORD. THE CONTRACTOR SHALL VERIFY THE CONDITION, LOCATION, AND QUANTITIES OF HAZARDOUS MATERIALS IN THIS WORK PRIOR TO SUBMITTING A BID. 5. REFER TO CONTRACT AND CONTRACTOR'S APPROVED WORK PLAN FOR ASBESTOS REMOVAL AND DISPOSAL PROCEDURES AND REQUIREMENTS. 6. ACMS AND ASSUMED ACMS IDENTIFIED IN THE LIMITED HAZARDOUS MATERIALS REPORT AS "SALVAGE" WILL BE REMOVED BY THE POE PRIOR TO COMMENCEMENT OF THE WORK. 16015th Avenue, Suite 1300 Seattle, Washington 98101 (206) 382-0600 Fax (206) 382-0500 PROJECT NO. 1600120 GENERAL NOTES: LEAD —CONTAINING MATERIALS 1. PAINTED SURFACES WERE FOUND TO CONTAIN LEAD (E.G., LEAD —CONTAINING PAINT - LCP). 2. REFER TO THE HAZARDOUS MATERIALS REMOVAL SPECIFICATIONS FOR IMPACTS TO LEAD COATED SURFACES. REFER TO SPECIFICATIONS FOR LEAD DISTURBANCES, DISPOSAL, AND TESTING REQUIREMENTS. 3. THE CONTRACTOR SHALL ASSUME THAT LEAD PAINT IS PRESENT ON ANY PAINTED BUILDING MATERIALS NOT TESTED. ALL WORK THAT MAY DISTURB PAINT —CONTAINING LEAD OR OTHER LEAD BUILDING MATERIAL SHALL BE IN ACCORDANCE WITH L&I REGULATION WAG 296-155-176, OSHA REGULATION 29 CFR 1926.62, AND THE SPECIFICATIONS, INCLUDING DUST CONTROL, EMPLOYEE EXPOSURE ASSESSMENTS AND WASTE CHARACTERIZATION. 1. INSPECT ALL LIGHT BALLASTS IN THE AREA, ALL MAGNETIC BALLASTS REGARDLESS OF LABELING AS "NO—PCBS" OR "PCB FREE", WILL BE REMOVED AND DISPOSED OF AS HAZARDOUS WASTE IN ACCORDANCE WITH THE REGULATIONS AND THE CONTRACTOR'S APPROVED WORK PLAN. PARTIAL DISASSEMBLY OF FLUORESCENT FIXTURES AND SELECTIVE DEMOLITION FOR ACCESS ARE INCLUDED IN THE SCOPE OF WORK, REFER TO CONTRACT SPECIFICATIONS/DRAWINGS, REGULATIONS, AND CONTRACTOR'S APPROVED WORK PLAN FOR PCB —BALLAST REMOVAL AND DISPOSAL PROCEDURES. HID LIGHTS ARE ASSUMED TO CONTAIN PCB —BALLASTS AND MERCURY —CONTAINING BULBS. BALLASTS LABELED "ELECTRONIC" MAY BE DISPOSED AS CONSTRUC I —ION DEBRIS, 2. ALL FLUORESCENT LIGHT TUBES AND HID LAMPS CONTAIN MERCURY AND WILL BE RECYCLED IN ACCORDANCE WITH THE CONTRACT SPECIFICATIONS AND WITHOUT BREAKAGE ON SITE. REFER TO THE CONTRACT SPECIFICATIONS, REGULATIONS, AND THE CONTRACTOR'S APPROVED WORK PLAN FOR LIGHT TUBE/HID LAMP RECYCLING PROCEDURES. 3. THE ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR ELECTRICAL ISOLATION OF ALL IMPACTED LIGHT FIXTURES AND THE ABATEMENT CONTRACTOR, SHALL VERIFY PRIOR TO COMMENCING WORK. 12/08/17 FD NO. DATE I BY ISSUED FOR BID AND PERMIT REVISION NO. I DATE I BY l F r r ! 's� ! D3.4 GENERAL NOTES, ABBREV'NS AND MAT'LS SUMMARY D3.5 HAZMAT — BUILDING T-5 DEMOLITION PLAN ,s0 �, v WINI Iiym! ABBRV'NS — ABBREVIATIONS ACM — ASBESTOS —CONTAINING MATERIAL AHERA -- ASBESTOS HAZARD EMERGENCY RESPONSE ACT BLDG — BUILDING CFR — CODE OF FEDERAL REGULATIONS EA — EACH HID HIGH INTENSITY DISCHARGE L&I DOSH — WASHINGTON STATE DEPARTMENT OF LABOR AND INDUSTRIES DIVISION OF OCCUPATIONAL SAFETY AND HEALTH LCP — LEAD —CONTAINING PAINT MAT'LS — MATERIALS OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION PCB — POLYCHLORINATED QIPHENYLS POE — PORT OF EVERETT PSCAA — PUGET SOUND CLEAN AIR AGENCY TYP R-- TYPICAL USEPA — US ENVIRONMENTAL PROTECTION AGENCY WAC — WASHINGTON ADMINISTRATIVE CODE PROJECT ENGINEER: A. BERGMAN DESIGNED BY: R. PETERSON DRAWN BY: F. DIMALANTA APPROVED) BY: SCALE: NONE DATE: 12/08/17 CHECKED BY: D. ESCAMIL LA PROJECT HAZARDOUS MATERIALS ,S11UihiARY QUANTITY/ UNIT DESCRIPTION (SEE LEGEND ON SHEET D3.5) 3 EA 15x4' & 1.5'x6' ELECTRICAL PANELS WITH ASSUMED ACM INTERNAL COMPONENTS 3 EA 4"x6" ELECTRICAL SWITCH GEAR PANELS WITH ASSUMED ACM INTERNAL COMPONENTS 2 EA B"x 16" & 12%30" ELECTRICAL SWITCH GEAR PANELS WITH ASSUMED ACM INTERNAL COMPONENTS 2 EA 2x4.5' ELECTRICAL SWITCH GEAR PANELS WITH ASSUMED ACM INTERNAL COMPONENTS 120 EA MERCURY --CONTAINING FLUORESCENT LIGHT TUBES AND HID BULBS 96 EA PCB —CONTAINING MAGNETIC LIGHT BALLASTS IF SHEET IS LESS THAN 22x34 REDUCE SCALE ACCORDINGLY CIP NO. 1—8-001-06 PROJECT NO. MT—ST--2017- 11 SHEET NO. 20 OF 176