|
SECTION 079200-JOINT SEALANTS
<br />PART1' GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A,Sbmittalsand color Samples.
<br />B.EnNronmenta|L|miteUona: Donot proceed with installation cfjoint sealants when ambient
<br />and substrate temperature conditions are outside limits permitted by joint -sealant
<br />manufacturer orare below 4Ddeg F(4.4deg C)
<br />PART2' PRODUCTS
<br />2.1JD|NTSEALANTS
<br />ACompatibility: Provide joint sealants, joint fillers, and other related materials that are
<br />compatible with one another and with joint substrates under service and application
<br />conditions.
<br />B. Sealant for Use inBuilding Expansion Joints:
<br />1 Single -component, neutral -curing silicone sealant, ASTM C82U.Type G; GnsdeNS;
<br />Class 5%for Use NT.
<br />C. Sealant for Use in Interior Joints in Ceramic Tile and Other Hard Surfaces in Kitchens
<br />and Toilet Rooms and Around Plumbing Fixtures:
<br />1.Sing le-uomponmnt.mildew-resistant silicone sealant, ASTM CO2O.Type S;Grade NS;
<br />Class 25;for Use NT;formulated with fungicide.
<br />D. Sealant for Interior Use at Perimeters of Door and Window Frames:
<br />1. Acrylic latex or si|inonizedaory|ic latexASTM C8O4.Type OP, Grade NF.
<br />E.Acoustical Sealant:
<br />1. Noneeg.peintable. nonstaining latex sealant complyingwith A8TMCO34that effectively
<br />reduces airborne sound transmission as demonstrated by testing according to ASTM E 90.
<br />2.2 MISCELLANEOUS MATERIALS
<br />AProvide sealant backings ofmaterial that are nonstaining; are compatible with joint
<br />substrates, sealants, primers, and other joint fillers; and are approved for applications
<br />indicated by sealant manufacturer based on field experience and laboratory testing.
<br />B.Cylindrical Sealant Backings: ASTMC133O.ofsize and density tocontrol sealant depth
<br />and otherwise contribute toproducing optimum sealant performance.
<br />C. Bond -Breaker Tape: Polyethylene tape orother plastic tape recommended bysealant
<br />manufacturer for preventing sealant from adhering torigid, inflexible joint -filler materials or
<br />joint surfaces otback nfjoint. Provide self-adhesive tape where applicable.
<br />D. Primer: Material recommended by joint -sealant manufacturer where required for
<br />adhesion ofsealant tojoint substrates indicated, aedetermined from preoonatructionjoint-
<br />aaa!ent-aubatrateteetsmndfie|dteoto.
<br />PART 3'EXECUTION
<br />3.1 INSTALLATION
<br />A,Comp|ywith ASTM C11S3.
<br />B. Install sealant backings tosupport aaa|enteduringspp|ioetionandtoproduueon000-
<br />eactiuns|ahapesanddepthoofinate||edsea|entothata||nwoptimumeoa|antmovement
<br />capability.
<br />C. Install bond -breaker tape behind sealants where sealant backings are not used
<br />between sealants and backs ofjoints.
<br />D. Acoustical sealant installation: eisound-rated assemblies and elsewhere eaindicated,
<br />seal perimeters, control joints, openings, and penetrations with a continuous bead of
<br />acoustical sealant. Install acoustical sealant otboth faces ofpartitions. Comply with
<br />ASTIMCS1S.
<br />END OF SECTION 079200
<br />SECTION 081113 - HOLLOW METAL DOORS AND FRAMES
<br />PART 1'GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A8ubmittals: Product Data and Shop Drawings Match Building Standards.
<br />PART 2-PRODUCTS
<br />2.1 MATERIALS
<br />ACold-Rolled Steel Sheets: AGTMA1OO8/A1OO8M.suitable for exposed applications.
<br />B.Hot-Rolled Steel Sheets: ASTMA1O11/A1O11K8.free ofscale, pitting, orsurface defects
<br />C. Metallic -Coated Steel Sheet: ASTK8A552646h3K8.G8O(Z18O)orA@U(ZF180.
<br />D. Frame Anchors: A8TMA5B1/A59188.4OZ(12G)coating designation; mill
<br />phoaphatioad.
<br />1 For anchors built into exterior walls, sheet steel complying with ASTM A 1008/A 1008M or
<br />A8TIMA1011/A1D11M hot -dip galvanized according toAGTMA158/A153M Class B.
<br />E. Inserts, Bolts, and Fasteners: Hot -dip galvanized according to ASTM A 153/A 153M.
<br />2.2 HOLLOW METAL DOORS AND FRAMES (MATCH BUILDING STANDARDS)
<br />A Fire -Rated Doors and Frames: Labeled by a testing and inspecting agency acceptable to
<br />authorities having jurisdiction, based on testing at positive pressure according to NFPA 252
<br />1. Where indicated, provide doors that that have a temperature rise rating of 450 deg F (250
<br />geQC).
<br />B.8mnke-Conbm|Door Aaeemb|iea� Comply with NFPA1O5orUL1784.
<br />C. Donna: Complying with ANSI 250.8for level and model and ANSI A25U.4for physical -
<br />endurance |eve| indicated, 1'3/4 inches (44mm)thick unless otherwise indicated.
<br />1.Interior Doors: Model 1 (Full Flush).
<br />2.Exterior Doors: Model 1(Full F|uah).metallic-coated steel sheet faces.
<br />3.Hardware Reinforcement: Fabricate according toANSI/SDI A250.0with reinforcement
<br />plates from ateh | as door face sheets,
<br />D. Frames: ANS|A25OO� conceal fastenings unless otherwise indicated.
<br />1.Steel Sheet Thickness for Interior Doors: Aoindicated inDoor Schedule onthe Drawings.
<br />2. Steel Sheet Thickness for Exterior Doors: Aaindicated inDoor Schedule onthe
<br />3. Fabricate interior frames with mitered orcoped and continuously welded corners.
<br />4. Fabricate exterior frames from metallic -coated steel sheet, with mitered or coped and
<br />continuously welded corners.
<br />5.Hardware Reinforcement: Fabricate according tnANSI/SDI A35U.0with reinforcement
<br />plates from same material aeframes,
<br />0.Frame Anchors: Not less than O.042inch (1.0mm)thick.
<br />EG|azingStopa: Nonnymovab|estops unoutside ofexterior doors and mnsecure side uf
<br />interior doors; eorew' |ied.vemovmb|*.g|ezin0etopeoninaide.febricmtedfromaamo
<br />material asdoor face sheet inwhich they are installed.
<br />F.Door Silencers: Three nnstrike jambs ofsingle-door frames and two onheads ofdouble-
<br />door frames.
<br />G. Grout Guards: Provide where mortar might obstruct hardware operation.
<br />H.Prepare doors and frames to receive mortised and concealed hardware according to
<br />ANSI A25O.0and ANSI A115Series standards.
<br />| Reinforce doors and frames Uoreceive auham+app|iedhardware.
<br />J. Prime Finish: Manufacturer's standard, factory -applied coat of lead- and chromate -free
<br />primer complying with ANSI/SDI A25O.1Oacceptance criteria.
<br />PART 3-EXECUTION
<br />3.1 INSTALLATION
<br />A,|nsta||hollow metal frames bocomply with ANS|/SD|A25O.11,
<br />1.Fire-Rated Frames: Install according toNFPAOO.
<br />B. Install doors to provide clearances between doors and frames as indicated in
<br />ANS|/SD|A25O.11
<br />C. Prime -Coat Touchup: Immediately after erection, sand smooth rusted nrdamaged
<br />areas ofprime coat and apply touchup ofcompatible air -drying rust -inhibitive primer. Use
<br />galvanizing repair paint for metallic coated surfaces.
<br />END OF SECTION 081113
<br />SECTION 0816110-PLASTIC LAMINATE FACED WOOD DOORS
<br />PART 1-GENERAL
<br />1.1 SUBMITTALS
<br />&ProductDeta: Submit sufficient manufacturer's data toindicate compliance with these
<br />specifications, including:
<br />1 Preparation instructions and recommendations.
<br />2,Storage and handling requirements and recommendations.
<br />3. Installation methods.
<br />B.Shop Drawings: Submit shop drawings coordinated with door frame and hardware
<br />requirements.
<br />1. Indicate door core material[s] and AWI construction type and high pressure decorative
<br />laminate selection.
<br />2.|ndicate door opening e|evadnno, sizma, typea, awinge, undercuts required and apode|
<br />blocking for hardware.
<br />3.Indicate plans and elevations, materials, profiles, assembly methods, accessories,
<br />hardware, and schedule offinishes.
<br />12 QUALITY ASSURANCE
<br />AFire-rated Doors: Conform to building code requirements for fire rating including but not
<br />limited to:
<br />1.Fire Door and Panel Construction: Conform toASTNE152 NFPA252orUL10B.
<br />2.Installed Fire -rated Door Assemblies toconform toMFPA 80for fire -rated class au
<br />scheduled.
<br />1.3 DELIVERY, STORAGE AND HANDLING
<br />AQoono: Deliver packaged individually inplastic and/or cardboard cartons.
<br />i. Mark each door on top and bottom rail with opening number used on Shop Drawings.
<br />2.K8arh peohe0os with aize, mwing, and door tag or opening number.
<br />B.Fnamoa: Deliver inindividual cartons ofheavy corrugated packaging material.
<br />1. Mark cartons with oize, mwing, and opening number.
<br />C. Store products in manufacturer's unopened packaging until ready for installation.
<br />1. Maintain plastic bags inplace during onsite handling and erection.
<br />2. Upon delivery open cartons and carefully inspect all doors for humidity damage.
<br />3. Contact manufacturer ifthere are questions orproblems.
<br />1.4PROJECT CONDITIONS
<br />A. Doors are man-made wood fiber products and are subject to the effects of humidity and
<br />temperature. Donot use inhigh humidity areas.
<br />B.Environmental Limitations:
<br />1. Donot deliver orinstall doors until building isenclosed, wet work iocomplete, and HVAC
<br />system is operating.
<br />2.Toensure product performance,etemperature range of 60'-80°Fand ohumidity range
<br />of35-55% must be maintained during storaga, installation and product life cycle.
<br />1.5CO8RD|NAT!ON
<br />A. Coordinate Work with door frame and door submittals, hardware fabrication and
<br />installation.
<br />1.0 WARRANTY
<br />A Standard Warranty: products shall bawarranted tubofree from defects for life of
<br />installation under normal use. Adhere tomanufacturer's requirements toavoid voiding
<br />warranty.
<br />PART PRODUCTS
<br />2.1 ACCEPTABLE MANUFACTURER ' MATCH BUILDING STANDARDS
<br />22DQORB
<br />A.3enena|: Flush wood doors faced with NEK0ALID 3.Grade NGS(O.O48inch (121mm)>thick
<br />high pressure plastic|aminate:
<br />1 Total Thickness: 1'3/4inches (44mm).
<br />2.Facing selection: High pressureplastic laminate selected from manufacturer's standard line
<br />ofsolids, patterns orwood grains.
<br />3.Edge Banding: Matching facing laminate.
<br />B.Non-FireRetedGo|id Core Doors:
<br />1.AWl Type PC-HDPL-5 and conforming hnVVVVDAiS]-A:
<br />a. Particleboard Core - average 30 pcf (480 kg/cu m) density core, complying with ANSI A208.1
<br />GradeLD-1
<br />2. Stiles and Rails: Structural composite |umber
<br />a.Stile and Top and Bottom Rail Widths '1-3k/8 inches (35mn)before trimming.
<br />O.Adheoive: National Casein CL18OgHVJ.
<br />C. 2D4MinuteFire Doors:
<br />1. Fire ITS (Warnock Hersey) 20-minute label.
<br />a.Particleboard Core - Average 3Opcf (48OKg/cum)density core complying with ANSI A208.1
<br />BradoLC-1.
<br />3.Stiles and Rails: Structural composite lumber.
<br />e.Stile and Top and Bottom Rail Widths -1-3/8 inches (35mm)before trimming.
<br />4.Adheoivo: Type iwaterproof H.B.Fuller XR285Q.
<br />5. Provide factory cutouts for lights. Stops are specified inseparate section.
<br />D. Fire Doors Rated Over2O Minutes.-
<br />1. Fire Rating:
<br />a. ITS i
<br />b� ITS (Warnock Hersey) 60-minute label.
<br />c.oTS /.
<br />d. ITS ratings specified ondrawings.
<br />a. Core: Non -asbestos mineral composition.
<br />b.Cr0004banding 1/10inoh thick 3-plywood cmae-banding,
<br />3. Sti|eoondFails: Fire retardant treated structural composite lumber.
<br />a.Stiles, 1-30inches (35mm)before trimming.
<br />b. Rails:
<br />1)Top 1^width.
<br />2) Bottom 2" width,
<br />4. Adhesive: Iwaterproof H.B. FuUerXR28GQ.
<br />2.3 FABRICATION
<br />A,Onmrs: Factory @ indicated, with the following uniform
<br />clearances and bevels, unless otherwise indicated:
<br />1. Comply with clearance requirements ofreferenced quality standard for non rated door fitting.
<br />2. Comply with requirements |nNFPA8Ofor fire -rated doors,
<br />3. Factory machine doors For hardware that ianot surface applied.
<br />B. Coordinate measurements of hardware mortises in metal frames to verify dimensions and
<br />alignment be -fore factory machining.
<br />C. Hardware Preparation: Prepare doors and frames for hardware specified indrawing
<br />schedule,
<br />D. Refinish field cut panel edges in accordance with manufacturer's instruction before
<br />installation.
<br />2.4SDURCE QUALITY CONTROL
<br />A./V|uwob|aFace Plane Tolerance (Te|egnaphing): Variation insurface offace not more than
<br />1/1OOinch (O25mm)from true plane inany 8inch (75mm)span.
<br />B. Allowable Warp Tolerance: Bow, cup, and twist not more than 1/4 inch (6mm) in any42
<br />inches (106.7cm) wide by 84 inches (213.3cm) high area, or less, if door dimensions are
<br />smaller; excluding doors less than 1-3/4inch (44mm)thick that are over 3Oinches (Q1.4om)
<br />wide or 84 inches (213,3cm) high and doors with cutouts exceeding manufacturer's specified
<br />limits,
<br />PART 3-EXECUTION
<br />3.1 PREPARATION
<br />Verify frames comply with indicated requirementsfortype.size, location, and swing
<br />characteristics and have been installed withlevel hednd plumb jambs. Verify wall thickness
<br />does not exceed manufacturer's recommsnded tolerances of specified throat size,
<br />32 INSTALLATION
<br />Install all materials in strict accordance with the manufacturer's installation instructions with
<br />doors in frames plumb and true, without rack, and so doors do not fall open or closed simply
<br />due to gravity.
<br />B. Securely anchor door frames in straight, plumb, and level condition without distortion of
<br />frames inaccordance with final shop drawings. Final adjustments shall bemade -for proper door
<br />operation. Brace frames inposition securely until permanent anchors are set. After wall
<br />construction is completed, remove temporary braces and spreaders leaving surfaces smooth
<br />and undamaged.
<br />1. Install doors with all hardware specified,
<br />3.3FIELD QUALITY CONTROL
<br />A.inota!|edimnTolerances: Install non fina-rateddoors with not more than 1/8^clearance a1top
<br />and sides, 1A"atbottom.
<br />3.4ADJUSTING, CLEANING AND PROTECTION
<br />A,Qperatiun: Aduatdoorandframefor-freeoperation without binding, rack, nrwarp. Re -hang
<br />orreplace doors that donot swing uroperate freely.
<br />B. Clean and remove dust and other foreign matter from panel and framing surfaces. Clean
<br />finishes inaccordance with manufacturer's instructions.
<br />C. Protect installed products until completion ofproject.
<br />END OF SECTION 08 1510
<br />SECTION 087100-DOOR HARDWARE - RE -USE EXISTING AND/OR MATCH EXISTING WITH
<br />NEW AS REQUIRED.
<br />PART 1-GENERAL
<br />11 SECTION REQUIREMENTS
<br />A.Submifte|e:
<br />1.Proposed eohed | pfdoor hordeenesetforrevew.
<br />_ Keying _schedule.
<br />B. Deliver keys to Own
<br />C. Fin+Reeistanm*RateUAoeamb|iea: Provide products that comply with NFPA8O and are listed
<br />and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction for
<br />applications indicated. On exit devices provide label indicating "Fire Exit Hardware."
<br />D. Accessibility Requirements: For door hardware on doors in an accessible route, comply with
<br />the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility
<br />PART 2'PRODUCTS
<br />2.1 HARDWARE
<br />AAll hardware tomatch existing finish and building standards.
<br />B.DoorPuUs Aluminum.
<br />C. Lever Hardware: Black stainless steel.
<br />D. Hi Stainless -steel hinges with stainless -steel pins for exterior.
<br />E. Lookaetsond Letchaeta:
<br />1 B#KX&A1582.Series 4000.Grade 1 for bored locks and latches.
<br />2. BHMAA15O.3.Grade 1for exit devices.
<br />3.8HMAA156.5.Grade 1-for auxiliary locks.
<br />4.BNMAA15O.12.Series 50OO.Grade 1-for interconnected locks and latches.
<br />5.BHK8AA15G.13.Series 1OD0.Grade 1for mortise locks and latches.
<br />0.Lever handles on!uuhsoteand |atohsets.brushed aluminum.
<br />7. Provide trim onexit devices matching locksets.
<br />F. Key locks toOwners existing master-keyoyste
<br />1.Cylinders with five -pin tumblers and removable cores.
<br />2. Provide cylinders for locking doors that donot require other hardware.
<br />3.Provide construction keying.
<br />4.Provide key control system, including cabinet.
<br />G. Closers:
<br />1.Mount closers oninterior side (room side) ofdoor opening. Provide regu|aponn.pyneUe|-enm.or
<br />top -jamb -mounted closers as necessary.
<br />2. Adjustable delayed opening(accessible topeop|evv|thdisabilities) feature onclosers.
<br />H. Sliding Door Hardware: BHMA Al 56.14; consisting of complete sets including rails, hangers,
<br />ouppurto, bumpnno, floor guides, and accessories indicated.
<br />I. Provide wall stops orfloor stops for doors without closers.
<br />J. Provide hardware finishes aafollows:
<br />1Hinges: Matching finish of|ookaet/|mtzhaet.
<br />2 Loukseto. Latchoeto. and Exit Devices: Tomatch existing.
<br />3. Closers: Matching finish of|oohae0atchemt.
<br />4,Other Hardware: Matching finish of|oukoet/lotchoe.
<br />PART 3- EXECUTION
<br />3.1 INSTALLATION
<br />A. Mount hardware in locations recommended by the Door and Hardware Institute unless
<br />otherwise indicated.
<br />END OF SECTION 087100
<br />SECTION 088000 - GLAZING
<br />PART 1'GENERAL
<br />11 SECTION REQUIREMENTS
<br />AGubmittals: Product Data and12-inch- (300-mmH square Samples.
<br />B.Fire-Resistance-Rated Assemblies: Provide omductathat com | ith NFPA8Oand are listed
<br />and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction for
<br />applications indicated.
<br />C. Safety
<br />D. Glazing Publications: Comply with published recommendations of glass product
<br />manufacturers and organizations below, unless more stringent requirements are indicated.
<br />/.,GMAPublication for Insulating Glass: SIGMA /M-ouuu."North American Glazing Guidelines for
<br />Sealed Insulating Glass Units for Commercial and Residential Uae,"
<br />E.8sfety Glazing Labeling.- Where safety glazinglabeling iaindicated, permanently mark glazing
<br />with certification label of the SGCC or another certification agency acceptable to authorities having
<br />jurisdiction orthe manufacturer. Label shall indicate manufacturer's name, type ofglass,
<br />dhiokneeo, and safety glazing standard with which glass complies.
<br />F.Fira-Protection'Retod Glazing Labeling: Permanently mark fire -protection -rated glazing with
<br />certification label of a testing agency acceptable to authorities having.jurisdiction, Label shall
<br />indicate manufacturer's name, test standard, whether glazing is for use in fire doors or other
<br />openings, whether or not glazing passes hose -stream test, whether or not glazing has a
<br />temperature hoe rating of45O deg F (250 deg C), and the fins'neaiatenoe rating in minutes.
<br />G. InSUlating-Glass Certification Program: Permanently marked either on spacers or on at least
<br />one component |itaofunits with appropriate certification label of|GCC.
<br />PART 2' PRODUCTS
<br />2.1 GLASS PRODUCTS
<br />&F|oetG|000: ASTNiC1O2O, Type LQuo|ity~O3
<br />D.Host-TreetadFloat Glass: ASTK8C1O48;Type |�Que|ity-Q3.
<br />22MIONOLITH|3-GLABBTYPES
<br />A,G|sooType: Clear fully tempered float glass.
<br />1. Thickness: 3/8and 1/2inch.
<br />2.4RRE-PRQTECTON-RATED GLAZING TYPES
<br />A.BlaseType: 45toQO-minutefire-rated glazing; 2MO-inuh'(3mm)thick, fire -protection -rated,
<br />laminated ceramic glazing.
<br />2.5 GLAZING SEALANTS
<br />A.G|ezingS*o|ent Neutral -curing silicone glazing sealant complying with ASTIMCB20.Type S.
<br />GnsdeNB. Class 25. Use NT.
<br />B.Glazing Sealants for Fire -Rated Glazing Products: Products that are approved by testing
<br />agencies that listed and labeled fire-resistant glazing products with which they are used for
<br />applications and fire -protection ratings indicated.
<br />PART 3' EXECUTION
<br />3.1 INSTALLATION
<br />Ainstall steel framing to comply with ASTM C 754 and with ASTM C 840 requirements that apply to
<br />framing installation and with United States Gypsum's "Gypsum Construction Handbook."
<br />1 Gypsum Plaster Assemblies: Also comply ithA8TM C841
<br />2. Portland Cement Plaster Assemblies: Also comply with ASTM C 1063.
<br />3. Gypsum Veneer Plaster Assemblies: Also comply with ASTM C 844.
<br />Bvnstaxsupplementary framing, d blocking to support fixtures, equipment services,heavy trim,
<br />grab bars, toilet accessories, furnishings, or similar construction.
<br />C. Isolate steel framing from building structure, except atfloor, to prevent transfer of loading
<br />imposed by structural movement.
<br />1. Where studs are installed directly against exterior walls, install asphalt -felt or foam -gasket
<br />isolation strip between studs and wall.
<br />D. Fire -Resistance -Rated Assemblies: Comply with requirements of listed assemblies.
<br />END OF SECTION 092216
<br />SECTION 092900 - GYPSUM BOARD
<br />PART1- GENERAL
<br />11 SECTION REQUIREMENTS
<br />B.Submittalu: Product Data.
<br />PART2' PRODUCTS
<br />2] PERFORMANCE REQUIREMENTS
<br />A.Fire+Reaistanm+RetedAaa*mb|iew: Provide materials and construction identical tnthose tested
<br />in assemblies perASTIM E 119 by an independent testing and inspecting agency acceptable to
<br />authorities having jurisdiction.
<br />B.STC-RatedAnaemb|ieo: Provide materials and construction identical tothose tested in
<br />assemblies per ASTM E 90 and classified per ASTM E 413 by a qualified independent testing and
<br />inspecting agency.
<br />2.2PANEL PRODUCTS
<br />A.Pmvideinmaximum lengths available tominimize end4o-endbutt joints.
<br />B.|nteriorGypsum Board: ASTK8C3O/C36MorAGTM C189G/C1896N1.inthickness indicated, with
<br />manufacturer's standard edges. Regular type unless otherwise indicated, Foil backed where
<br />indicated. Type X where indicated. Type as required for specific fire -resistance -rated assemblies.
<br />Sag -resistant typefor ceiling surfaces.
<br />C. VVatepReoistantGypeum Backing Board: ASTM C 620/C 630M orABTM C 1396/C 1396M. in
<br />thickness indicated. Regular type unless otherwise indicated. Type X where required for fire -
<br />resistance -rated assemblies and where indicated.
<br />D. Giseo-Mat.Water-Resistant Gypsum Backing Board: ASTKXC1178/C1178M.nfthickness
<br />indicated. Regular type unless otherwise indicated. Type X where required for fire -resistance -rated
<br />assemblies and where indicated.
<br />1. Product: G-P Gypsum; Dens -Shield Tile Guard (Bonim'of-Deaign).
<br />E.CemeniitioumBacker Units: ANSI A118.Q.
<br />2.3ACCESSOR|ES
<br />A.Trim Accessories: ASTM C 1047, formed from galvanized or aluminum -coated steel sheet, rolled
<br />zinc, p|aotic, or paper -faced galvanized -steel sheet. For exterior trim, use accessories formed from
<br />hot -dip galvanized -steel sheet, plastic, orrolled zinc.
<br />1.Provide oumarbeedatoutside corners unless otherwise indicated.
<br />2.Provide LC -bead (J' ead) at exposedpone|adges.
<br />3.Provide control joints where indicated.
<br />B.A|uminum40000aories: Extruded -aluminum accessories indicated with manufacturer's
<br />standard corrosion -resistant primer.
<br />C. Joint -Treatment Materials: AGTIMC475/C475M.
<br />1.Joint Tape: Paper unless otherwise recommended bypanel manufacturer.
<br />2.Joint Compounds: Setting -type taping compound and drying -type, ready'mixed, compounds for
<br />topping.
<br />O.Skim Coat: For final coat oMLevel 5finieh. use high -build iteh coating product designed for
<br />application airless soraver and hobeused instead ofskim coat toonoduoeLevel 55niah
<br />4. CnmnnUtioumBacker Unit Joint -Treatment Materials: Products recommended bycementitiouo
<br />backer unit manufacturer.
<br />END OF SECTION 092900
<br />SECTION 096613-RESILIENT BASE AND ACCESSORIES
<br />PART 1- GENERAL
<br />11 SECTION REQUIREMENTS
<br />A,Submitta|a: Product Data and Samples.
<br />B.Extra Materials: Deliver tnOwner otleast 1Dlinear feet (3linear m)ofeach type and color of
<br />resilient wall base installed.
<br />PART PRODUCTS
<br />21 RESILIENT BASE ' MINIMIZE SEAMS
<br />ACo|orand Pattern: Aaindicated inthe Finish Legend onthe Drawings.
<br />B.Gtyle:C with toe) ethard surface areas and straight base atCarpet.
<br />C. Minimum Thickness: O.125inch (32mm).
<br />D. Height Aaindicated onthe Drawings.
<br />E.Longtha: Coils in manufacturers standard lengths.
<br />F.Outside Corners: Job formed orpreformed.
<br />G. Inside Corners: Job formed orpreformed.
<br />H.Finioh:Aaselected.
<br />2.2RESILIENT MOLDING ACCESSORY
<br />A,Co|or As selected by Architect from manufacturers standard colors.
<br />B.QeaohpUon: Transition strip between carpet and hard surfaces.
<br />C. N1etehai Rubber.
<br />D. Profile and Dimensions: As indicated.
<br />23RESILIENT MOLDING ACCESSORY
<br />A,Co|or Manufacturer's standard.
<br />B.Deoohption: Transition strip between carpeand tile.
<br />C. Material: Stainless steel.
<br />D. Profile and Dimensions: Aoindicated onthe Drawings,
<br />2.4INSTALLATION ACCESSORIES
<br />ATrmwo|ab|eLeveling and Patching Compounds: Letex-modi5ed.porUandcement- orblended
<br />hydraulic cement -based formulation provided or approved by flooring manufacturer for applications
<br />indicated.
<br />BAdheaiveo: Water-resistant type recommended by manufacturer to suit products and substrate
<br />conditions.
<br />C. Metal Edge Strips: Extruded aluminum with mill finish of width shown, of height required to protect
<br />exposed edges of tiles, and in maximum available lengths to minimize running joints.
<br />PART EXECUTION
<br />3.1 INSTALLATION
<br />A. Prepare concrete substrates according toASTIMF71O' Verify that substrates are dry and free of
<br />curing compounds, aee|ano, and hardeners.
<br />B.Adhesively install resilient wall base and accessories.
<br />C. Install wall base inmaximum lengths possible. Apply towalls, columns, pilasters, casework, and
<br />other permanent lixLureeinrooms orareas where base ierequired,
<br />D. Install stair -tread -nose filler to nosing substrates that do not conform to tread contours.
<br />E.Install reducer strips at edges of floor coverings that would otherwise be exposed.
<br />END OF SECTION 096613
<br />SECTION 096813-TILE CARPETING
<br />PART GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />B. Submittals: Product Data and Samples.
<br />C. Extra Materials: Deliver toOwner carpet tiles equal to5percent of
<br />each type and color carpet tile installed, packaged with protective covering
<br />for storage.
<br />PART2 PRODUCTS
<br />2.1 CARPET TILE
<br />A. Carpet Tile: Anindicated inFinish Legend unthe Drawings.
<br />G. Primary Backing: Aoindicated inthe Finish Legend onthe Drawings.
<br />C, Secondary Backing: Aaindicated inthe Finish Legend onthe Drawings.
<br />D. Size: Aoindicated inFinish Legend onDrawings.
<br />E, Critical Radiant Flux Classification: Not less than O.45VWoq.omper
<br />ASTNE 648.
<br />PART8' EXECUTION
<br />3.1 INSTALLATION
<br />A, Comply with CR|1O4.
<br />B. Installation Method: Aarecommended bymanufacturer.
<br />C. Install borders parallel towalls.
<br />END OF SECTION096813
<br />SECTiON 099123-INTERIOR PAINTING - SEE FINISH PLAN, CEILING PLAN, AND FINISH SCHEDULE
<br />PART1-GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals:
<br />1PmductDato.|mcludephntouofM,P|'s^MP|AppmvedProdudsListwithpmducthigh|ighted.
<br />2.8amp|eo.
<br />B. Mockups: Full -coat finish Sample of each type of coating, color, and substrate, applied where
<br />directed.
<br />C, Extra Materials: Deliver to Owner 1 quart (0.9 L) of each color and type of finish coat paint used
<br />onProject, incontainers, properly labeled and sealed.
<br />PART2- PRODUCTS
<br />2.1 PAINT
<br />A, Available Product: Regal Pearl; Benjamin K8onne&Co. (Gaoio+uf-Doe
<br />B. MP!Standarde:Providemeterie|ethatnomp|ysithMP|atandardoindicatedand|istediniba''MP|
<br />Approved Products List.^
<br />C. Material Compatibility: Provide materials that are compatible with one another and with
<br />substrates.
<br />1. For each coat in a paint system, provide products recommended in writing by manufacturers of
<br />topcoat for use inpaint system and onsubstrate indicated.
<br />D. Use paints and coatings that comply with the following limits for VOC content:
<br />1 Flat Paints andCoatings: 50
<br />u.Anticorrosive and ant|ruotPaints Applied tuFerrous Metals: 250Q/L
<br />4.Primers, Sealers, and Undercoatem: 200g/L
<br />5.Dry-FogCoatings: 4OOg/L.
<br />G.Zinc'Rich Industrial Maintenance Primers: 340Q/L
<br />7.Pretreatment Wash Primers: 420g/L
<br />8.Staina: 250g/L,
<br />E. Colors: Aaselected byArchitect from manufacturer's full range,
<br />PART 3- EXECUTION
<br />3,1 PREPARATION
<br />A. Comply with recommendations inK0P|'a''11pI Architectural Painting Specification K8anua|"
<br />applicable iosubstrates indicated,
<br />B. Remove hardware, lighting fixtures, and similar items that are not to be painted. Mask items that
<br />cannot beremoved. Reinstall items ineach area after painting iocomplete.
<br />C. Clean and prepare surfaces in an area before beginning painting in that area. Schedule painting eo
<br />cleaning operations will not damage newly painted surfaces.
<br />3.2 APPLICATION
<br />A. Comply with recommendations in M Pi's "M PI Architectural Painting Specification Manual"
<br />applicable 10substrates indicated.
<br />B. Paint exposed surfaces, new and existing, unless otherwise indicated.
<br />1 Paint surfaces behind movable equipment and furniture same as similar exposed surfaces.
<br />2. Paint surfaces behind permanently fixed equipment or furniture with prime coat only.
<br />3.Paint the back side ofaccess panels.
<br />4.Color-code mechanical piping inaccessible ceiling spaces.
<br />5.Donot paint prefinished items, items with an integral finish, operating parts, and labels unless
<br />otherwise indicated.
<br />C� Apply paints according tomanufacturer's written instructions.
<br />1 Use rollers for finish coat oninterior walls and ceilings.
<br />D� Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks,
<br />roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color
<br />breaks.
<br />'I. If undercoats or other conditions show through topcoat, apply additional coats until cured film has a
<br />uniform paint finish, color, and appearance.
<br />E. Apply stains and transparent finishes to produce surface films without color irregularity,
<br />cloudiness, holidays, lap merkn, brush merko, runo, ropiness, orother imperfections, Use multiple
<br />coats to produceesmooth surface film ofeven luster.
<br />3.3 INTERIOR PAINT APPLICATION SCHEDULE
<br />A. Steel:
<br />1. Semigloss,Quick-Dry Enamel: Two coats over quick -drying alkyd metal primer: IMP| |NT5jA.
<br />2. Satin Latex: Two coats over quick -drying alkyd MP| |NT51Q.
<br />3. Semigloss, |: Two coats over quick -drying alkyd primer: MP|INT51E.
<br />B. Galvanized Metal:
<br />1. Satin Latex: Two coats over waterborne galvanized -metal primer: MFI|NT5.3J.
<br />C. Aluminum:
<br />1.Semigloss Latex: Two coats for 5.4H.
<br />2. Semigloss, Alkyd Enamel: Two coats over quick -drying primer for aluminum: MP||#T54J.
<br />D. Gypsum Board:
<br />1 Semigloss Two coats over primer/sealer: MPIINT9.2A.
<br />2. Semigloss Alkyd: Two coats over latex primer/sealer: MPIlNT9.2C.
<br />E. DressedLumber: Including architectural woodwork and doors.
<br />1. Semigloss Alkyd: Two coats over alkyd primer: MPIINT6.3B.
<br />z.Semigloss, Alkyd Varnish: Two coats over stain and alkyd sanding sealer nrshellac: MPIINT
<br />O,3D.
<br />3. Semigloss, Alkyd Varnish: Two coats over alkyd sanding sealer orshellac: K8P!INTO.3J.
<br />4.GloasPolyurethane: Two coats over stain: MP|INT0.3E.
<br />END OF SECTION 099123
<br />SECTION 104413-FIRE EXTINGUISHER CABINETS
<br />PART1- GENERAL
<br />11 SECTION REQUIREMENTS
<br />A. Submittals: Product Data.
<br />EL Fim-Ratad.Fire-Protection Cabinets: Listed and labeled tocomply with requirements inASTME
<br />814for fire -resistance rating ofwalls where they are installed.
<br />PART 2' PRODUCTS
<br />2.1 FIRE-PROTECT|ONCAB|NETS
<br />A. Fire -Protection Cabinets: Enameled -steel, recessed cabinets for fire extinguisher.
<br />B. Cabinet Construction: Nonrated.
<br />C. Cabinet Material: Match existing.
<br />1 Trim and Material: Match existing.
<br />D. Door Material: Match existing.
<br />1.Door Style: Match existing.
<br />E. Accessories: Match existing.
<br />F. Finishes: Manufacturer's standard baked -enamel paint tomatch existing.
<br />PART 5' EXECUTION
<br />3.1 INSTALLATION
<br />A. Install cabinets atheights acceptable to authorities having jurisdiction.
<br />D. Fire -Rated Hose orValve Cabinets: Install cabinet with not more than 1/16-|nch (1.6'mm)
<br />tolerance between pipe ODand knockout OD. Seal through penetrations with §nastoppingsealant.
<br />C. Identification: Apply Ueos|m or vinyl lettering at locations indicated on Drawings.
<br />END OF SECTION 104413
<br />SECTION 1RE EXTINGUISHERS
<br />PART1 GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data.
<br />PART2- PRODUCTS
<br />2.1 FIRE EXTINGUISHERS AND BRACKETS
<br />A. Portable Fire Extinguishers: NFPA1U.listed and labeled for the type, rating, and classification uf
<br />extinguisher.
<br />1.Multipurpose Dry -Chemical Type: UL-rated2'A:1U-B:C. 5'|b(23-kg) nominal capacity, inenameled-
<br />aluminum container.
<br />B. Mounting Brackets: Manufacturer's standard ste| designed fire extinguisher howall or
<br />structure, ofsizes requiredforfineexUnguiohmnaindiceted.wbhp|otedorbeked~anem*|finiuh.
<br />PART 3' EXECUTION
<br />31 INSTALLATION
<br />A. Install mounting brackets in locations indicated at heights acceptable to authorities having
<br />]uriadiution.
<br />B. Install fire extinguishers inmountingbrmcketaandosbinetsxvhereindicoted,
<br />END OF SECTUONi04416
<br />PROVIDE: 5%ATTC STOCK OFCPT, CEILING TILE, PAINT, LYT G.C. TO CONFIRM
<br />ALL % WITH COMCAST
<br />StanteoArchiteoture Inc.
<br />9Y9l0hStreet Suite 2O2
<br />Denver COBO202
<br />|(3O 7
<br />w*w.sfnn,uccom
<br />Copyright Reserved
<br />The Contractor shall
<br />responsible for all dimensions. ooNOT
<br />scale the drawing any errors ur
<br />omissions shall uoreported tostonteo
<br />without delay.
<br />The Copyrights ,oall designs and
<br />drawings are the property o/ountuc
<br />Reproduction v,use for any purpose
<br />other than that authorized brman,ec
<br />is forbidden.
<br />Consultant
<br />Permit/Seal
<br />6
<br />�
<br />
|