|
CAU I ION: 11- IHIS SHEEI IS NOI J0x42 11 IS A REDUCED PRINI
<br />____
<br />MILLWORK NOTES
<br />- --"---.----
<br />FINISH NOTES
<br />CEILING NOTES
<br />FLOOR PLAN NOTES
<br />I
<br />DEMOLITION NOTES
<br />DESIGN BUILD NOTES
<br />n,
<br />0
<br />ll
<br />>_
<br />---
<br />
<br />-
<br />1
<br />11
<br />r-
<br />:
<br />=
<br /><
<br />1. CONTRACTOR MUST NOTIFY ARCHITECT / DESIGNER OF ANY DISCREPANCY IN
<br />h
<br />c
<br />PLANS. FINISH ITEMS CLEARLY SHOWN IN PLANS, BUT OMITTED FROM SCHEDULES
<br />1. NO FINISH SUBSTITUTIONS MAY BE MADE UNLESS APPROVED BY ARCHITECT,
<br />1.
<br />SEE ELECTRICAL ENGINEERING DRAWINGS FOR SPECIFICATIONS OF NEW BUILDING
<br />1.
<br />CONTRACTOR AND ARCHITECT TO REVIEW & APPROVE CHALK LINES OF PARTITION
<br />1.
<br />DRAWINGS OF EXISTING CONDITIONS HAVE BEEN COMPILED FROM EXISTING DATA
<br />1.
<br />LIGHT SWITCHES SHALL BE INSTALLED AT +48" A.F.F. MULTIPLE SWITCHES
<br />�_
<br />OR LEGENDS MUST STILL BE PROVIDED AND INSTALLED BY CONTRACTOR.
<br />STANDARD LIGHT FIXTURES, SWITCHES, EXIT SIGNS, ETC.
<br />LAYOUT PRIOR TO COMMENCEMENT OF PARTITION CONSTRUCTION.
<br />SUPPLIED BY THE OWNER TO THE ARCHITECT. THE ARCHITECT MAKES NO
<br />SHOULD BE GANGED T HERWISE SPECIFIED.
<br />� = �
<br />CONTRACTOR TO VERIFY OMITTED FINISHES WITH ARCHITECT OR DESIGNER PRIOR
<br />2. CONTRACTOR MUST NOTIFY THE ARCHITECT OF ANY DISCREPANCY IN PLANS.
<br />WARRANTY, EITHER EXPRESS OR IMPLIED, FOR THE ACCURACY OF THE
<br />:2
<br />TO ORDERING PRODUCTS.
<br />FINISH ITEMS CLEARLY SHOWN IN PLANS, BUT OMITTED FROM SCHEDULES OR
<br />2.
<br />ALL REPLACEMENT FLUORESCENT LAMPS TO MATCH BUILDING STANDARD - SAME
<br />2.
<br />CONTRACTOR TO VERIFY DIMENSIONS FOR ALL PLUM31NG PARTITION.
<br />COMPLETENESS OF THE EXISTING INFORMATION RECORDED. THE CONTRACTOR
<br />2.
<br />CONTRACTOR TO VERIFY ALL SWITCH LOCATIONS WITH THE ARCHITECT PRIOR TO
<br />Lij
<br />0
<br />LEGENDS MUST STILL BE PROVIDED AND INSTALLED BY CONTRACTOR.
<br />TURER.
<br />SHALL FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY THE ARCHITECT
<br />INSTALLATION. NUMBER OF SWITCHES FOR OPEN AREA IS BIDDER DESIGN.
<br />z
<br />I 11
<br />2. SHOP DRAWINGS MUST BE PROVIDED FOR APPROVAL PRIOR TO FABRICATION TO
<br />FY OMITTED FINISHED WITH ARCHITECT PRIOR TO ORDERING
<br />3.
<br />EXTEND ALL STUDS AND WALL MATERIALS TO CONSTRUCTION ABOVE, U.O.N.
<br />IMMEDIATELY OF ANY DISCREPANCIES OR CONFLICTS THAT MIGHT ARISE IN THE
<br />SWITCHES INDICATED ON THE DRAWINGS FOR OPEN AREA ARE FOR REFERENCE
<br />- 5:
<br />m
<br />THE ARCHITECT. CABINETMAKER SHALL USE ON SITE FIELD FRAMING DIMENSIONS
<br />3.
<br />FIELD VERIFY EXISTING CEILING GRID LOCATION AND NOTIFY ARCHITECT OF ANY
<br />LITION WORK.
<br />ONLY.
<br />0
<br />0
<br />FOR ALL SHOP DRAWINGS AND FABRICATIONS. ANY SUBSTITUTIONS TO THE
<br />!�
<br />DISCREPANCIES ON PLANS.
<br />4.
<br />ALL CONDUIT PIPING IN ELECTRICAL ROOM TO BE CONCEALED WITHIN THE WALL
<br />1
<br />w
<br />FOLLOWING SPECIFICATIONS MUST BE APPROVED BY THE ARCHITECT PRIOR TO
<br />3. INSTALL MATERIALS ACCORDING TO MANUFACTURER'S SUGGESTED INSTALLATION
<br />CONSTRUCTION.
<br />2.
<br />VERIFY LOCATIONS OF EXISTING MECHANICAL, PLUMBING AND ELECTRICAL
<br />3.
<br />CONTRACTOR SHALL PROVIDE SEISMIC BRACING AT ALL NEW AND RELOCATED
<br />=
<br />I -
<br />FABRICATION.
<br />AND PREPARATION/MAINTENANCE SPECIFICATIONS OR BETTER, UNLESS OTHERWISE
<br />1 4.
<br />WHERE DISCREPANCIES IN LOCATION OF LIGHT FIXTURES, AIR DIFFUSERS, GRILLES,
<br />UTILITIES. LOCATE AND PROTECT UTILITIES TO REMAIN. DISCONNECT, REMOVE
<br />LIGHT FIXTURES.
<br />APPROVED OR NOTED.
<br />ETC. OCCUR ON THE ELECTRICAL ENGINEERING PLANS, THE ARCHITECTURAL
<br />5.
<br />DOOR OPENINGS IN PARTITIONS NOT DIMENSIONED ARE TO BE LOCATED WITHIN
<br />NCTION BOX OR PANEL, AS REQUIRED, AND CAP
<br />I
<br />�0_
<br />3. CABINET MAKER TO COORDINATE & VERIFY WITH CONTRACTOR FINAL LOCATION
<br />PLANS SHALL GOVERN. NOTIFY ARCHITECT OF ANY DISCREPANCIES FOR
<br />0'-4" OF ADJACENT PERPENDICULAR PARTITION.
<br />DESIGNATED UTILITIES WITHIN THE DEMOLITION AREA. REFER TO THE
<br />4.
<br />CONTRACTOR SHALL VERIFY AND PROVIDE A COMPLETE HVAC SYSTEM WHICH
<br />ry
<br />OUNTERS FOR IN -WALL SUPPORT BRACKETS, PRIOR TO
<br />4. APPLICATION OF CONTROLLED INTERIOR FINISHES SHALL BE IN CONFORMANCE
<br />CLARIFICATIONS.
<br />MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL INFO.
<br />CONFORMS TO THE OWNER'S HVAC SPECIFICATIONS. CONTRACTOR SHALL BE
<br />0
<br />0:�
<br />GYPSUM BOARD FINISHING OF WALLS. ALL FINAL INSTALLATION HEIGHTS FOR
<br />WITH STATE & LOCAL CODES.
<br />�
<br />6.
<br />CONTRACTOR SHALL USE 3-5/8" METAL STUDS MINIMUM AT ALL PLUMBING
<br />RESPONSIBLE FOR ALL ROOF PENETRATIONS AND PATCHING, ANY SCREENING OF
<br />n
<br />IN -WALL SUPPORT BRACKETS MUST MEET ALL APPLICABLE ACCESSIBILITY CODES
<br />5.
<br />FIELD VERIFY ALL CLEARANCES OF DUCTS, PIPES, SPRINKLERS, ETC., AND NOTIFY
<br />WALLS. CONTRACTOR TO VERIFY ACTUAL DEPTH REQUIRED, ANY DISCREPANCIES
<br />3.
<br />EXISTING ELECTRICAL AND TELEPHONE OUTLETS LOCATED ON DEMOLISHED WALLS
<br />ROOF -MOUNTED MECHANICAL UNIT REQUIRED BY GOVERNING JURISDICTION.
<br />m
<br />:2
<br />AND STANDARDS WITH COUNTER TOP MATERIAL THICKNESS INCLUDED.
<br />5. DECORATIVE MATERIALS SHALL BE MAINTAINED IN A FLAME-RETARDANT
<br />ARCHITECT OF ANY CONFLICTS PRIOR TO INSTALLATION OF LIGHTS, ETC.
<br />SHALL BE REPORTED TO THE ARCHITECT.
<br />ARE TO BE REMOVED INCLUDING CONDUIT AND WIRING BACK TO JUNCTION BOX.
<br />I
<br />I
<br />- C
<br />CONDITION.
<br />E PATCHED AND REPAIRED TO BE FLUSH WITH ADJACENT
<br />0
<br />-i
<br />_
<br />4. MATERIAL COLORS NOT LISTED SHALL BE REQUESTED FROM ARCH � TECT/� N TERIOR
<br />DESIGNER ON SHOP DRAWING SUBMITTALS OR BY LETTER.
<br />6.
<br />PLACEMENT OF LIGHT FIXTURES IN AREAS WHERE MAIN DUCTS MAY CAUSE
<br />INTER PROVED BY ARCHITECT PRIOR TO INSTALLATION.
<br />7.
<br />USE WATER RESISTANT GYPSUM BOARD/FIBER BOARD AT ALL AREAS SUBJECT TO
<br />MOISTURE OR WHERE TILE IS USED.
<br />WALL SURFACE.
<br />I
<br />I
<br />FIRE AUTHORITY NOTES
<br /><
<br />m
<br />11
<br />ICLI
<br />6. SUBMIT THE FOLLOWING SAMPLES FOR ARCHITECT'S APPROVAL:
<br />A. THREE (3) 12" X 12" SAMPLES FOR ALL PAINT AND STAIN BRUSHOUTS,
<br />I
<br />1
<br />4.
<br />WHERE PLUMBING FIXTURES ARE BEING REMOVED OR WHERE EXPOSED PLUMBING
<br />�
<br /><
<br />5. ALL UPPERS TO BE LAMINATED TO MATCH BASE CABINETS. BOTH UPPERS &
<br />VINYL AND FABRIC FINISHES AND COLORS APPLIED TO A SUBSTRATE WHICH
<br />i 7.
<br />CONDUITS ABOVE CEILING MUST BE A MINIMUM OF 12" ABOVE THE CEILING GRID.
<br />B.
<br />ALL PLUMBING WORK SHALL BE IN ACCORDANCE WITH LOCAL AND NATIONAL
<br />PIPES OCCUR, CAP LINES BEHIND FINISHED SURFACES. PATCH AND REPAIR AS
<br />3:
<br />-
<br />LOWER CABINETS IN WET AREAS TO HAVE MATCHING PVC EDGE, ALL OTHERS TO
<br />IS REPRESENTATIVE OF THE SURFACE TO BE FINISHED. SUBMIT PAINT
<br />!
<br />R
<br />CODES.
<br />REQUIRED.
<br />LL_
<br />0
<br />HAVE PLASTIC LAMINATE EDGE BANDING U.O.N.
<br />SAMPLES FROM THE PAINT LOT OR LOTS INTENDED FOR APPLICATION.
<br />1 8.
<br />�
<br />NO COMBUSTIBLE MATERIALS SHALL BE USED IN THE PLENUM SPACE, INCLUDING
<br />LL�
<br />I
<br />Il
<br />ALUMINUM FLEX, ALUMINUM CONDUIT, AND POT METAL CONNECTORS.
<br />9.
<br />ALL HOT WATER LINES SHALL BE PROPERLY INSULATED. SEE PLUMBING
<br />5�
<br />ALL EXISTING CONSTRUCTION WHERE INDICATED INCLUDING ELECTRICAL,
<br />1.
<br />FINAL INSPECTION BY FIRE DEPARTMENT IS REQUIRED - SCHEDULE 72 HOURS IN
<br />L-)
<br />6. ALL CABINETS AND DOORS SHALL BE CONSTRUCTED FROM 3/4" THICK MATERIAL,
<br />B. ONE (1) 24'g X 24" MOCK-UP WITH SAMPLE SEAM (CENTERED) OF ALL
<br />DRAWINGS,
<br />TELEPHONE, PLUMBING AND MECHANICAL DEVICES NOT OTHERWISE INDICATED ON
<br />ADVANCE.
<br />�_
<br />0
<br />71
<br />UNLESS APPROVED PRIOR TO EACH JOB.
<br />FABRIC AND VINYL FINISHES AND COLOR.
<br />9.
<br />ALL JUNCTION BOXES AND MECHANICAL EQUIPMENT REQUIRING ACCESS FOR
<br />THESE CONSTRUCTION DRAWINGS SHALL BE REMOVED IN A CAREFUL MANNER SO
<br />LLJ
<br />SERVICE SHALL BE LOCATED OVER ACOUSTICAL CEILINGS. NO ACCESS HATCHES
<br />10.
<br />ALL PLUMBING CLEAN -OUTS SHALL BE INSTALLED WHERE READILY ACCESSIBLE.
<br />AS NOT TO DAMAGE ADJOINING CONSTRUCTION.
<br />2.
<br />THE PROJECT ADDRESS SHALL BE PROVIDED FOR ALL NEW AND EXISTING
<br />=
<br />7. ALL BASE CABINET ARE NOT TO RECEIVE WALL BASE UNLESS INDICATED ON
<br />C. THREE (3) 12" X 12" SAMPLES OF ALL FLOOR COVERING.
<br />SHALL BE INSTALLED IN GYPSUM BOARD CEILINGS WITHOUT PRIOR APPROVAL BY
<br />CONTRACTOR SHALL COORDINATE ALL CLEAN -OUT LOCATIONS WITH EQUIPMENT,
<br />BUILDINGS IN A POSITION AS TO BE PLAINLY VISIBLE AND LEGIBLE FROM THE
<br />-
<br />�_
<br />0
<br />FINISH PLANS OR ELEVATIONS.
<br />ARCHITECT. (NO EXCEPTION)
<br />AND CABINETS. SUBMIT A PLAN OF ALL PROPOSED LOCATIONS TO ARCHITECT
<br />5.
<br />IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO LOCATE ALL EXISTING
<br />STREET OR ROAD FRONTING THE PROPERTY PER LOCAL FIRE DEPARTMENI
<br />�_
<br />FOR APPROVAL PRIOR TO INSTALLATION.
<br />UTILITIES WHETHER SHOWN HEREON OR NOT AND TO PROTECT THEM FROM
<br />STANDARDS.
<br />�__
<br />8. ALL INTERIORS OF CLOSED CABINETS TO BE WHITE MELAMINE/POLYESTER OR
<br />D. SUBMIT ACTUAL CUTTINGS OF EACH PRODUCT FOR COLOR/QUALITY CONTROL.
<br />10.
<br />�l
<br />ALL SPRINKLER HEADS AT HARD -LID CEILINGS ARE TO BE FULLY RECESSED AND
<br />DAMAGE. THE CONTRACTOR SHALL BEAR ALL EXPENSE OF REPAIR OR
<br />=
<br />0
<br />APPROVED EQUAL, UNLESS OTHERWISE SPECIFIED.
<br />CONCEALED. HEADS ARE TO BE CENTERED BETWEEN LIGHTS IN A UNIFORM
<br />ll�
<br />ALL MILLWORK SHALL CONFORM TO STATE & LOCAL WOODWORKING STANDARDS.
<br />REPLACEMENT OF UTILITIES OR OTHER PROPERTY DAMAGED BY OPERATIONS IN
<br />3.
<br />AN UNOBSTRUCTED ALL-WEATHER FIRE APPARATUS ACCESS ROAD SHALL BE IN
<br />=)
<br />0
<br />7. WHERE MATERIALS ARE NOT RETURNABLE, SUBMIT SAMPLES TO ARCHITECT
<br />ARCHITECTURAL PATTERN. G.C. TO PROVIDE A SUBMITTAL WITH SPRINKLER HEAD
<br />CONJUNCTION WITH THE EXECUTION OF HIS WORK.
<br />PLACE PRIOR TO DELIVERY OF COMBUSTIBLE BUILDING MATERIALS TO THE SITE.
<br />C-1
<br />9. ALL OPEN CABINETS OR SHELVES TO HAVE PLASTIC LAMINATE TO MATCH
<br />BEFORE PLACING FULL ORDERS.
<br />i
<br />HITECT'S APPROVAL PRIOR TO INSTALLATION.
<br />12.
<br />FIELD MEASURE AS REQUIRED FOR ALL MILLWORK CONDITIONS PRIOR TO
<br />9
<br />m
<br />h�
<br />EXTERIORS.
<br />FABRICATION.
<br />7.
<br />ALL EXISTING BUILDING UTILITIES SHALL REMAIN IN OPERATION DURING
<br />4�
<br />FIRE PREVENTION WATER SERVICE SHALL BE IN SERVICE PRIOR TO DELIVERY OF
<br />m
<br />8. SUBMIT SEAMING PLAN FOR ALL FLOOR FINISHES TO ARCHITECT FOR APPROVAL
<br />11.
<br />ALL G NGS ARE TO BE INSTALLED WITH LINEAR DIFFUSERS.
<br />CONSTRUCTION. PROVIDE REROUTING OF UTILITIES SERVING ADJACENT AREAS
<br />COMBUSTIBLE BUILDING MATERIALS TO THE SITE.
<br />__�
<br />__j
<br />10. NO 3/4" THICK SHELF SHALL SPAN LONGER THAN 32" WITHOUT SUPPORT.
<br />PRIOR TO ORDER.
<br />G.C. TO PROVIDE A SUBMITTAL WITH ALL LINEAR DIFFUSER LOCATIONS PRIOR TO
<br />13.
<br />CONTRACTOR TO PROVIDE SHOP DRAWINGS FOR ARCHITECT AND TENANT
<br />THAT ARE TO MAINTAIN UNINTERRUPTED SERVICE. ANY TEMPORARY SUSPENSION
<br /><
<br />=
<br />INSTALLATION.
<br />APPROVAL PRIOR TO MANUFACTURE OF ANY CABINET WORK, MILLWORK AND ANY
<br />OF SERVICE SHALL BE COORDINATED AND APPROVED BY THE FACILITY MANAGER,
<br />5.
<br />ACCESS GATES SHALL BE APPROVED PRIOR TO INSTALLATION AND SHALL BE IN
<br />cr,
<br />11. ALL SHELVING TO BE ADJUSTABLE UNLESS OTHERWISE SPECIFIED,
<br />9. NOTIFY ARCHITECT IMMEDIATELY OF ITEMS WITH LONG LEAD TIMES.
<br />OTHER SPECIAL ITEMS REQUIRING CUSTOM SHOP FABRICATED WORK.
<br />NOT LESS THAN 24-HOURS IN ADVANCE.
<br />COMPLIANCE WITH LOCAL FIRE AUTHORITY.
<br />>_
<br />0
<br />"FRONT
<br />10. ALL PAINT FINISH OF METAL PARTS OF DOORS, HANDRAILS, PERIMETER
<br />12.
<br />LOCATE RECESSED DOWN LIGHTS, WALL WASHERS, SMOKE DETECTORS, EXIT SIGNS,
<br />SPEAKERS, FIRE SPRINKLERS, ETC. IN CENTER OF 24N24" CEILING TILES OR IN
<br />14.
<br />CONTRACTOR TO VERIFY FINAL LOCATION FOR CANTILEVERED COUNTERS AND
<br />8.
<br />THE CONTRACTOR WILL VERIFY AND CONFORM TO ALL REQUIREMENTS OF ALL
<br />6.
<br />FIRE SPRINKLER SYSTEM(S) SHALL MEET STATE & LOCAL FIRE CODES AND BE
<br />z
<br /><
<br />a_
<br />12. ALL FILE PEDESTALS ARE TO BE CONFIGURED FOR TO BACK" FILING AND
<br />ENCLOSURES, ETC., SHALL BE SEMI -GLOSS, U.O.N.
<br />CENTER OF 24%24" PORTION OF 24"X48" CEILING TILES, UNLESS OTHERWISE
<br />IN -WALL SUPPORT BRACKETS PRIOR TO GYPSUM BOARD FINISHING OF WALLS.
<br />UTILITY COMPANIES UNLESS OTHERWISE NOTED IN THE PLANS AND
<br />CT ENTIRE BUILDING INCLUDING PROJECTIONS OVER 4'-O".
<br />ui
<br />n,
<br />FOLDERS, UNLESS NOTED AS LATERAL.
<br />11. WHERE PAINT COLORS CHANGE, CORNERS ARE TO BE CUT -IN FREE OF
<br />NOTED.
<br />ALL FINAL INSTALLATION HEIGHTS FOR IN -WALL SUPPORT BRACKETS MUST MEET
<br />SPECIFICATIONS.
<br />0
<br />OVERLAPPING.
<br />ALL ACCESSIBILITY CODES REQUIREMENTS WITH COUNTERTOP MATERIAL THICKNESS
<br />7.
<br />FIRE SPRINKLER SYSTEM(S) AND ALL CONTROL VALVES, INCLUDING EXTERIOR
<br />0
<br />13. ALL COUNTER TOPS TO BE 24" DEEP, UNLESS OTHERWISE SPECIFIED. WHERE NO
<br />13.
<br />PROVIDE SWITCHES AND LIGHT SENSORS FOR OPEN AREAS AND PRIVATE OFFICES.
<br />INCLUDED.
<br />9.
<br />THE DEMOLITION PLAN KEYNOTES ARE DIAGRAMMATIC AND GENERAL IN NATURE.
<br />SHALL BE SUPERVISED BY A U.L. LISTED CENTRAL ALARM STATION OR PER
<br />>_
<br />=
<br />BACKSPLASH IS SPECIFIED, COUNTER TOPS TO BE SCRIBED TIGHTLY TO BACK &
<br />12. PRIOR TO THE INSTALLATION OF WALL COVERINGS, SURFACES SHALL BE
<br />ACTUAL LOCATION OF ALL SWITCHES TO BE DETERMINED BY ELECTRICAL
<br />THE INTENT IS TO ILLUSTRATE THE COMPLETE DEMOLITION OF THE SPACES
<br />INDICATED UNLESS NOTED OTHERWISE. FIELD VERIFICATION OF EXISTING
<br />ODES.
<br /><
<br />SIDE WALLS.
<br />D WITH SEALER PER MANUFACTURER'S RECOMMENDATIONS.
<br />ENGINEER.
<br />15.
<br />PROVIDE AND INSTALL ALL NECESSARY WALL BACKING, STIFFENERS, BRACING,
<br />BACK -UP PLATES BRACKETS AS REQUIRED FOR THE
<br />CONDITIONS AND SPECIFIC QUANTITIES IS THE RESPONSIBILITY OF THE
<br />8.
<br />ALL VALVES CONTROLLING THE WATER SUPPLY FOR AUTOMATIC SPRINKLER
<br />uj
<br />I -
<br />m
<br />14. ALL BACKSPLASHES TO BE SCRIBED TO WALLS, AND MUST BE FLUSH TO EDGE
<br />13. CONTRACTOR TO VERIFY CONDITION AND LEVEL OF FLOOR SO AS TO RECEIVE
<br />14.
<br />WHERE EXIT SIGNS ARE REQUIRED PER STATE & LOCAL CODES, THEY SHALL BE
<br />INSTALLATION OF WALL -MOUNTED OR SUSPENDED EQUIPMENT OR BUILT-IN ITEMS.
<br />CONTRACTOR.
<br />SYSTEMS AND WATER -FLOW SWITCHES ON ALL SPRINKLER SYSTEMS SHALL BE
<br />m
<br />OF BASE, UNLESS OTHERWISE SPECIFIED. ALL COUNTER TRANSITION SEAMS MUST
<br />NEW FINISHES WITHOUT BOWING AT FLOOR OR WALL BASE. CONTRACTOR IS
<br />ILLUMINATED PER SAID CODES AND THE NEC. LOCATIONS SHALL BE
<br />VERIFY REQUIREMENTS WITH MANUFACTURERS PRIOR TO INSTALLATION. SUPPLY
<br />10.
<br />REMOVAL AND DISPOSAL OF DEMOLITION DEBRIS IS THE RESPONSIBILITY OF THE
<br />ELECTRICALLY MONITORED WHERE THE NUMBER OF SPRINKLERS IS (100) OR
<br />0
<br />.)
<br />BE CAULKED SEALED, VERIFY EITHER MATCHING COLOR CAULK OR CLEAR
<br />RESPONSIBLE FOR ALL FLOOR PREPA RATION.
<br />n
<br />COORDINATED WITH THE ARCHITECT.
<br />CATALOG CUT SHEETS FOR ARCHITECT'S APPROVAL.
<br />CONTRACTOR. VERIFY THE HAULING ROUTE THROUGH THE BUILDING, THE
<br />MORE�
<br />Li
<br />=
<br />SILICONE.
<br />14. ALL CARPETING SHALL BE INSTALLED WITH GLUE DOWN METHOD, U.O.N.
<br />15.
<br />PROVIDE BACK-UP POWER FOR EXIT SIGNS PER STATE & LOCAL CODES.
<br />16.
<br />PROVIDE AND INSTALL ALL NECESSARY ELECTRICAL CONNECTIONS AND PLUMBING
<br />DEMOLITION STAGING AREA, AND THE LOCATION OF THE DUMPSTERS WITH THE
<br />OWNER PRIOR TO THE START OF DEMOLITION. DISPOSAL OF RUBBISH SHALL BE
<br />9.
<br />ELECTRICAL SUBCONTRACTORS TO INSTALL WIRING FOR FIRE SPRINKLER, ALARM
<br />�_
<br />z
<br />-15. PROVIDE SIDE SPLASHES AT LOCATIONS ADJACENT TO WALLS OR WINDOWS,
<br />SUPPLY, FITTINGS & CONNECTORS TO COMPLETE INSTALLATION OF APPLIANCES &
<br />DONE IN A LEGAL MANNER.
<br />BELL AND TELEPHONE WARNING AS REQUIRED BY FIRE DEPARTMENT.
<br />0
<br />ESPECIALLY FOR SINKS U.O.N.
<br />15. WHERE FLOOR -MOUNTED OUTLETS ARE REQUIRED ON CARPETED AREA, CUT
<br />16.
<br />THE MEANS OF EGRESS, INCLUDING THE EXIT DISCHARGE, SHALL BE ILLUMINATED
<br />EQUIPMENT INDICATED ON PLAN. VERIFY REQUIREMENTS NTH MANUFACTURERS
<br />n
<br />Lij
<br />CARPET IN AN 'Y' OVER FLOOR HOLE AND INSTALL CARPET OVER TOP. DO NOT
<br />TO A LEVEL OF NOT LESS THAN ONE FOOT CANDLE AT THE WALKING SURFACE
<br />PRIOR TO INSTALLATION. SUPPLY CATALOG CUT SHEETS FOR ARCHITECT'S
<br />11.
<br />THE OWNER RESERVES THE RIGHT TO SALVAGE ANY DEMOLISHED ITEM. VERIFY
<br />10.
<br />INSTALLATION OF FIRE ALARM SYSTEMS SHALL BE IN ACCORDANCE WITH STATE &
<br />F.-
<br />E
<br />16. FACES OF PIGEONHOLES TO MATCH WORK SURFACE LAMINATE. COLOR OF EDGE
<br />AT ALL TIMES THE BUILDING SPACE SERVED BY THE MEANS OF EGRESS IS
<br />APPROVAL.
<br />ED WITH THE OWNER PRIOR TO THE START OF DEMOLITION.
<br />LOCAL FIRE CODES.
<br />Li
<br />BANDING ON ALL DOORS TO MATCH FACE MATERIAL.
<br />OCCUPIED.
<br />REMOVE, PROTECT, CLEAN, REPAIR FOR REUSE AND TURN OVER SUCH ITEMS AS
<br />-'>
<br />Id
<br />1
<br />16. ALL V.C.T. TO BE INSTALLED WITH FULL TILE FROM VINYL THRESHOLD STRIP AND
<br />17.
<br />EXACT LOCATION OF FIRE EXTINGUISHER CABINETS TO BE CONFIRMED WITH
<br />DIRECTED BY THE OWNER.
<br />11.
<br />COMPLETE PLANS AND SPECIFICATIONS FOR ALL FIXED FIRE PROTEC11ON
<br />m
<br />17. SEE SPECIFICATIONS/PROJECT MANUAL FOR ADDITIONAL REQUIREMENTS.
<br />FULL TILE FROM WALL ADJACENT TO DOOR SWING, U.O.N.
<br />17.
<br />EMERGENCY LIGHTING SHALL BE (2) SEPARATE SOURCES OF POWER AND SHALL
<br />ARCHITECT BEFORE INSTALLATION. PROVIDE ADDITIONAL FIRE EXTINGUISHERS &
<br />EQUIPMENT INCLUDING AUTOMATIC SPRINKLERS AND OTHER FIRE -PROTECTION
<br />-il
<br />COMPLY WITH THE NEC.
<br />CABINETS AS REQUIRED BY THE FIRE DEPARTMENT FIELD INSPECTORS.
<br />12.
<br />IN ORDER TO INSTALL SOME OF THE NEW WORK (INCLUDING, BUT NOT LIMITED
<br />SYSTEMS, SHALL BE SUBMITTED BY INSTALLING CONTRACTOR. SUCH PLANS
<br /><
<br />m
<br />18. COUNTERTOPS SHALL HAVE A NOSING OF COUNTERTOP MATERIAL AT LEAST 3"
<br />17. PROVIDE AND INSTALL SPECIFIED BASE FOR ALL AREAS TO RECEIVE FLOORING.
<br />I
<br />TO MECHANICAL, PLUMBING OR ELECTRICAL) IT WILL BE NECESSARY FOR THE
<br />SHALL BE APPROVED BY LOCAL FIRE AUTHORITY PRIOR TO INSTALLATION.
<br />V)
<br />DEEP, WHEREBY THE COUNTER MATERIAL EXTENDS INTO THE INSIDE OF THE
<br />18.
<br />PROVIDE FIRE DAMPERS AT ALL SUPPLY AND RETURN AIR OUTLETS, INLETS OR
<br />VRIFY LOCATION OF ALL THERMOSTATS WITH ARCHITECT PRIOR
<br />CONTRACTOR AND HIS SUBCONTRACTORS TO REMOVE AND REPLACE (OR
<br />m
<br />17,
<br />CABINET, I.E. OVER THE DOOR (WHEN PRESENT).
<br />18. CONTRACTOR SHALL PROVIDE PRE -FORMED RUBBER BASE CORNERS. DO NOT
<br />DUCTS PENETRATING FIRE RATED ASSEMBLIES, ENCLOSURES, WALLS, FLOORS OR
<br />TO INSTALLATION.
<br />12.
<br />LOCATIONS AND CLASSIFICATIONS OF FIRE EXTINGUISHERS SHALL BE IN
<br /><
<br />CUT OR BEND STRAIGHT BASE TO MAKE CORNERS.
<br />SURFACES, AND AS REQUIRED BY THE FIRE DEPARTMENT.
<br />REFINISH) EXISTING WALLS, FLOORS, OR CEILING IN THE AREAS OF THE BUILDING
<br />ACCORDANCE WITH STATE & LOCAL FIRE CODES AND PLACEMENT IS SUBJECT TO
<br />V)
<br />19. END PANELS AND FRONT EDGES OF EDGE PANELS WHICH ARE PROUD OF THE
<br />19.
<br />ALL EXITS SHALL HAVE EXIT SIGNS AND ALL BLIND CORRIDOR TURNS SHALL
<br />NOT SHOWN ON THESE PLANS. THE CONTRACTOR SHALL INCLUDE ALL RELATED
<br />THE APPROVAL OF THE FIRE INSPECTOR. VERIFY QUANTITY & EXACT LOCATION
<br />=
<br />0
<br />INTERIOR CABINET SHALL BE FACED TO MATCH DOOR FRONTS.
<br />I
<br />19. MILLWORK LOWER CABINETS ARE NOT TO RECEIVE WALL BASE UNLESS INDICATED
<br />19.
<br />CONTRACTOR SHALL PROVIDE EMERGENCY LIGHTING, STROBE LIGHTS,
<br />HAVE DIRECTIONAL EXIT SIGNS.
<br />COSTS IN HIS BASE BID, WHETHER SHOWN ON THESE PLANS OR NOT.
<br />FROM FIRE DEPARTMENT PRIOR TO ORDERING.
<br />V)
<br />ON FINISH PLANS.
<br />AUDIO-VISUAL ALARMS AND OCCUPANCY SENSORS TO MEET ALL APPLICABLE
<br />=
<br />w
<br />S T
<br />20, ALL HINGED DOOR HAVE CLEAR SILENCERS TOP AND BOTTOM ON DOOR (NOT
<br />CODES.
<br />20.
<br />PREPARE ALL FLOOR SURFACES AS REQUIRED TO RECEIVE FINISHES AS NOTED
<br />13.
<br />PROTECT ADJACENT SPACES NOT SCHEDULED FOR DEMOLITION. PATCH AND
<br />13.
<br />AT LEAST ONE (1) FIRE EXTINGUISHER WITH A MINIMUM RATING OF:
<br />:2
<br />r')
<br />IG
<br />"OPEN
<br />ON FINISH PLAN, ENLARGED FINISH PLANS & FINISH LEGEND.
<br />REPAIR DAMAGED FINISHES, ITEMS AND FIXTURES TO REMAIN AND/OR REPLACE
<br />2-A-108:C (FOR OFFICE), OR 10-A-808:C (FOR WAREHOUSE), SHALL BE
<br />CABINET).
<br />20. FLOOR FINISHES TO CONTINUE UNDERNEATH FLOOR" AREAS OF MILLWORK,
<br />20.
<br />CONTRACTOR SHALL PROVIDE LAMPS WITH TYPE IC RATED HOUSING WHERE
<br />IN KIND TO MATCH EXISTING FROM DAMAGE DURING THE PROGRESS OF THE
<br />PROVIDED WITHIN 75-0" MAXIMUM TRAVEL DISTANCE FOR EACH 3,000 SQUARE
<br />c�
<br />bi
<br />INCLUDING SINK AREA AND AT ALL UNDER -COUNTER EQUIPMENT AREAS WHICH
<br />FIXTURES COME IN DIRECT CONTACT WITH INSULATION.
<br />21.
<br />UNLESS OTHERWISE NOTED, ALL GYPSUM BOARD SURFACES, WALLS, AND CEILINGS
<br />WORK. PROVIDE TEMPORARY SAFETY BARRIERS REQUIRED BY CODE AND AS
<br />FEET OR PORTION THEREOF ON EACH FLOOR.
<br />-i
<br /><
<br />21. ALL DRAWERS GLIDES SHALL HAVE SILENCERS BUILT INTO THE GLIDE AND NOT
<br />OR.
<br />SHALL BE TAPED, SANDED SMOOTH TO A "LEVEL 4" FINISH, SO AS TO RECEIVE
<br />INDICATED TO INSURE PUBLIC SAFETY AND TO ALLOW BUILDING OCCUPANCY.
<br />0
<br />U)
<br />INSTALLED ON THE DRAWER OR DRAWER FRONT.
<br />21. FLOORS SHALL BE SLOPED TO FLOOR DRAINS. COORDINATE WITH PLUMBING AND
<br />21.
<br />EXIT SIGNS SHALL BE INTERNALLY OR EXTERNALLY ILLUMINATED AT ALL TIMES
<br />PAINT OR WALL COVERING MATERIAL.
<br />MIT FOR APPROVAL, BARRIER LOCATIONS, AND METHOD OF
<br />14.
<br />STORAGE, DISPENSING OR USE OF ANY FLAMMABLE AND COMBUSTIBLE LIQUIDS,
<br />n,
<br />Ld
<br />22. ALL DRAWER GLIDES SHALL BE FULL EXTENSION.
<br />STRUCTURAL DRAWINGS. IN RATED FLOOR CONDITIONS, CONFIRM REMAINING FLOOR
<br />AND SHALL BE CONNECTED TO AN EMERGENCY POWER SYSTEM (BATTERIES, UNIT
<br />HE ARCHITECT PRIOR TO INSTALLATION.
<br />FLAMMABLE AND COMPRESSED GASES, AN MATERIALS SHALL
<br />>
<br />0
<br />THICKNESS STILL CONFORMS TO MINIMUM RATING REQUIREMENT.
<br />EQUIPMENT OR AN ON -SITE GENERATOR) THAT WILL AUTOMATICALLY ILLUMINATE
<br />22.
<br />PROVIDE SOUND INSULATION AT PERIMETER WALLS OF RESTROOMS, LOBBY,
<br />COMPLY WITH STATE & LOCAL FIRE CODES. THE STORAGE AND USE OF
<br />w
<br />THE EXIT SIGNS FOR A DURATION OF NOT LESS THAN 90 MINUETS.
<br />STAIRS, AND ACROSS CEILING OF RESTROOMS TO CREATE AN ACOUSTIC
<br />14.
<br />NO STRUCTURAL ELEMENTS ARE INCLUDED IN THIS SCOPE OF WORK.
<br />HAZARDOUS MATERIALS SHALL BE APPROVED BY THE FIRE AUTHORITY PRIOR TO
<br />0
<br />23. ALL HINGES SHALL OPEN ±105% EXCEPT WHERE CABINETS ARE ADJACENT TO THE
<br />ENVELOPE, U.O.N.
<br />ANY MATERIALS BEING STORED OR USED ON SITE. A SEPARATE PLAN SUBMITTAL
<br />:2-1
<br />LLJ
<br />WALLS. PROVIDE HINGES WHICH LIMIT THE DOOR SWING TO KEEP THE DOOR PULL
<br />22. CONTRACTOR TO RUN CALCIUM CHLORIDE TEST ON ALL EXISTING OR NEW
<br />15.
<br />PROVIDE DUST BARRIERS AROUND OPENINGS, TO AND FROM THE CONSTRUCTION
<br />IS REQUIRED PRIOR TO THE STORAGE AND USE OF HAZARDOUS MATERIALS.
<br />in
<br />W
<br />FROM DAMAGING THE WALL.
<br />CONCRETE SLABS PRIOR TO INSTALLING ANY FLOORING AND COMPARE RESULTS
<br />23.
<br />PATCH AND FILL VARIOUS OPENINGS AT EXISTING GYPSUM BOARD PARTITIONS
<br />AREA. PROVIDE ALL MEANS NECESSARY TO INHIBIT DUST FROM ENTERING
<br />0
<br />�
<br />WITH FLOORING MANUFACTURE'S RECOMMENDED MAXIMUM CONTENT FOR
<br />AND SOFFITS FOLLOWING REMOVAL OR INSTALLATION OF ANY SURFACE MOUNTED
<br />OTHER PORTIONS OF THE FACILITY. SUBMIT BARRIER LOCATIONS TO THE
<br />15.
<br />BUILDING(S) NOT APPROVED FOR HIGH -PILED STOCK (MATERIALS IN CLOSELY
<br />Li
<br />of
<br />n
<br />OR RECESSED FURNISHINGS, RECEPTACLES, UTILITY PIPING, SHELF STANDARDS &
<br />ARCHITECT FOR APPROVAL, PRIOR TO INSTALLATION.
<br />PACKED PILES OR ON PALLETS, OR IN RACKS WHERE THE TOP OF STORAGE
<br />w
<br />23. PRIOR TO NEW FLOORING INSTALLATION REMOVE EXISTING FLOOR FINISHES. PATCH
<br />ALL OTHER SIMILAR ELEMENTS INDICATED TO BE REMOVED DURING THE
<br />15.
<br />PROVIDE ADEQUATE SHORING, BRACING, BARRICADES AND PROTECTIVE MEASURES
<br />EXCEEDS 12'-O" IN HEIGHT, AND 6'-O" FOR GROUP "A" PLASTICS AND CERTAIN
<br />��
<br />I <
<br />AND REPAIR SUB -FLOOR AS REQUIRED. PREPARE FLOORS AND TRANSITIONS AS
<br />DEMOLITION PHASE OR INSTALLED DURING THE CONSTRUCTION PHASE: TAPE AND
<br />AS REQUIRED TO SAFELY EXECUTE THE WORK IN THE CONSTRUCTION AREA AND
<br />OTHER HIGH -HAZARD COMMODITIES). HIGH -PILED STOCK SHALL BE APPROVED
<br />__j
<br />REQUIRED FOR SMOOTH AND LEVEL FINISH PER APPLICABLE BUILDING CODES.
<br />SEAL ALL SEAMS WITH JOINT COMPOUND: APPLY NEW FINISH TO MATCH EXISTING
<br />TO THE CONSTRUCTION AREA. CEASE OPERATIONS AND
<br />BY THE FIRE AUTHORITY PRIOR TO MATERIALS BEING STORED ON SITE. A
<br />_j
<br /><
<br />FINISH AT ADJACENT GYPSUM BOARD SURFACES AND FEATHER NEW FINISH WITH
<br />EXISTING FINISH TO PROVIDE CONSISTENT & CONTINUOUS FINISH.
<br />NOTIFY THE ARCHITECT IMMEDIATELY IF THE STRUCTURE APPEARS TO BE
<br />SEPARATE PLAN SUBMITTAL IS REQUIRED FOR HIGH -PILED STORAGE IN
<br />=
<br />(n
<br />24, ALL FLOORING TRANSITIONS AMONG ALL THE DIFFERING FLOORING MATERIAL
<br />ENDANGERED. DO NOT RESUME OPERATIONS UNTIL CORRECTIVE MEASURES HAVE
<br />ACCORDANCE WITH STATE & LOCAL FIRE CODES.
<br />U)
<br />SPECIFICATION TYPES ARE TO BE A FLUSH TRANSITION.
<br />BEEN TAKEN.
<br />16.
<br />A LETTER OF INTENDED USE MAY BE REQUIRED BY THE FIRE INSPECTOR.
<br />71
<br />0
<br />cn
<br />�
<br />25. FEATHER SUB -FLOOR UP FOR A) TILE FLOORING TO CARPET AND B) VINYL
<br />L__
<br />__ -_ 11 - -
<br />17.
<br />CONTRACTOR SHALL MAINTAIN REQUIRED MEANS OF EGRESS AND ENSURE THAT
<br />=
<br />Li
<br />FLOORING TO CARPET, FOR FLUSH INSTALLATION.
<br />EXIT ROUTES ARE SIGNED, LIGHTED AND PROTECTED IN ACCORDANCE WITH CODE
<br />17.
<br />ALL REQUIRED FIRE DOORS SHALL BEAR A LABEL FROM A RECOGNIZED AGEN
<br />�
<br />26. INSTALL METAL TRANSITION STRIPS WHERE TILE MEETS ALL OTHER FLOORING
<br />DOOR NOTES
<br />POWER & SIGNAL NOTES
<br />REQUIREMENTS, RELOCATE EXISTING AND/OR PROVIDE SMOKE PROTECTORS AND
<br />SHOWING THE SPECIFIC RATING.
<br />n
<br />m
<br />U�
<br />LIFE SAFETY EQUIPMENT FOR ADEQUATE COVERAGE.
<br />t_
<br />TYPES. PROVIDE LOW PROFILE TRANSITION STRIP WHERE ALL OTHER DIFFERENT
<br />18.
<br />EXIT SIGNS AND ILLUMINATION SHALL CONFORM TO ALL APPLICABLE BUILDING
<br />�_
<br />FLOOR TYPES MEET, VERIFY COLOR.
<br />.
<br />-_
<br />._____
<br />18.
<br />PROVIDE TEMPORARY NON-COMBUSTIBLE CONSTRUCTION BARRIERS WHERE
<br />AND FIRE CODES.
<br />[if
<br />3:
<br />I
<br />1
<br />1
<br />�
<br />AT/CHEMICAL SEAM VINYL FLOORING AS PER
<br />REQUIRED BY CODE AND THE GOVERNING FIRE AUTHORITY. MINIMUM
<br />REQUIREMENTS:
<br />19.
<br />EXIT DOORS SHALL BE OPERABLE FROM THE INSIDE WITHOUT THE USE OF A KEY
<br />rri
<br />:E
<br />I
<br />MANUFACTURER'S SPECIFICATIONS AND SEAL ALL VINYL FLOORS PER
<br />1.
<br />VERIFY THAT ALL DOORS AND DOOR HARDWARE MEET THE REQUIREMENTS OF ALL
<br />1.
<br />COORDINATE TELEPHONE/DATA INSTALLATION WITH APPROPRIATE
<br />OR ANY SPECIAL KNOWLEDGE OR EFFORT,
<br />0
<br />C-)
<br />MANUFACTURER'S MAINTENANCE SPECIFICATIONS.
<br />GOVERNING CODES & STANDARDS. NOTIFY THE ARCHITECT IMMEDIATELY IN CASE
<br />SUB -CONTRACTOR.
<br />A. FULL HEIGHT WALL FROM FLOOR TO CEILING.
<br />__j
<br /><
<br />�
<br />OF DISCREPANCY.
<br />B STUDS AT 24" O.C., WITH 5/8" TYPE Y GYPSUM BOARD.
<br />20.
<br />PROVIDE OR MODIFY AS NEEDED SPRINKLER ALARM AND SMOKE DETECTION
<br />�2_:
<br />28. FLOOR COVERING INSTALLER TO FOLLOW MANUFACTURER'S SPECIFIED CARPET
<br />2.
<br />ALL EXISTING ELECTRICAL DEVICES ARE TO REMAIN, UNLESS NOTED OTHERWISE.
<br />*
<br />C. NON-COMBUSTIBLE ACCESS DOOR WITH (3) HINGES AND SPRING CLOSER.
<br />BLE CODES INCLUDING IF NECESSARY FOR HORNS, STROBE
<br />LIGHTS, CONTROL PANEL CONNECTIONS, SMOKE DETECTORS, AUDIO 'VISUA
<br />, III
<br />fl,
<br />INSTALLATION INSTRUCTIONS. USING ADHESIVES AND INSTALLATION METHODS
<br />2.
<br />FIELD MEASURE, AS REQUIRED, ALL DOORS PRIOR TO FABRICATION.
<br />ALARMS. SUBMIT SHOP DRAWINGS TO THE FIRE MARSHAL FOR APPROVAL.
<br /><
<br />3:
<br />�
<br />REQUIRED INSTRUCTIONS TO MAINTAIN PRODUCT'S WARRANTY. CONTACT CARPET
<br />3.
<br />PROVIDE A SIGN ON OR NEAR THE MAIN EXIT DOOR READING:
<br />3.
<br />ALL OUTLETS TO BE INSTALLED AT LOCATIONS SHOWN BY DIMENSIONS ON THE
<br />POWER & SIGNAL PLAN. DIMENSION ALL OUTLETS FROM THE CENTERLINE OF THE
<br />19.
<br />SURVEY EXISTING FLOORS AND CLEARLY MARK ON FLOOR SURFACE THE
<br />=
<br />I I -
<br />TIVE WITH QUESTIONS PRIOR TO PROCEEDING.
<br />"THIS DOOR TO REMAIN UNLOCKED WHEN BUILDING IS OCCUPIED".
<br />OUTLET BOX. NON -DIMENSIONED OUTLETS ARE TO LOCATED AT THE NEAREST
<br />LOCATIONS OF ALL BEAMS AND JOISTS. MARK ALL CORE DRILL PENETRATIONS
<br />-_
<br />_.- - 11 -
<br />3�:
<br />R
<br />WALL STUD.
<br />AND RECEIVE STRUCTURAL ENGINEER'S APPROVAL PRIOR TO DRILLING CONCRETE.
<br />I-
<br />29. FLOOR COVERING INSTALLER TO FOLLOW MANUFACTURER'S SPECIFIED CONTOURED
<br />4.
<br />VERIFY THAT EXISTING DOORS COMPLY WITH ACCESSIBILITY REQUIREMENTS.
<br />I
<br />r
<br />7�1 1
<br />III
<br />�
<br />I
<br />RUBBER BASE INSTALLATION INSTRUCTIONS USING ADHESIVES AND INSTALLATION
<br />4.
<br />WHEN OUTLETS ARE GROUPED TOGETHER (2 OR MORE), THEY ARE TO BE SPACED
<br />20.
<br />CUT RIGID MATERIALS USING MASONRY SAW OR CORE DRILL. PNEUMATIC TOOLS
<br />:E
<br />Li
<br />1
<br />METHODS REQUIRED TO MAINTAIN PRODUCT'S WARRANTY.
<br />5.
<br />RATED DOORS SHALL COMPLY WITH REQUIREMENTS OF ALL GOVERNING CODES &
<br />NO MORE THAN 2" APART.
<br />ARE NOT ALLOWED WITHOUT PRIOR APPROVAL.
<br />w
<br />cx�
<br />i
<br />S A RECOGNIZED AGENCY SHOWING
<br />CD
<br /><
<br />30. FLOOR COVERING INSTALLER REQUIRED TO PROVIDE MINIMAL SEAMS/JOINTS AT
<br />THE SPECIFIC RATINGS.
<br />5.
<br />ALL ELECTRICAL OUTLETS OF 30 AMPERES OR LESS SHALL BE MOUNTED BETWEEN
<br />21.
<br />ALL CORE DRILLING OR OTHER NOISY WORK SHALL BE SCHEDULED 48-HOURS IN
<br />>_
<br />I
<br />ALL LOCATIONS FOR FLOOR AND WALL BASE MATERIAL INSTALLATION. PROVIDE
<br />+15" TO BOTTOM RECEPTACLE AND +48" TO TOP OF RECEPTACLE FROM FINISH
<br />ADVANCE WITH THE OWNER.
<br />�
<br />.
<br />LOW VOC, BUT HEAVY DUTY ADHESIVES TO ENDURE HEAVY FOOT TRAFFIC, CARTS
<br />6.
<br />ALL HARDWARE TO BE LEVER -TYPE PER GOVERNING CODES & ACCESSIBILITY
<br />FLOOR. SEE NOTE 6, BELOW, FOR GENERAL MOUNTING HEIGHT
<br />22.
<br />APPLY CEMENT BASE FLOOR PATCH AS REQUIRED TO FILL DINGS, NAIL HOLES,
<br />�_
<br />n
<br />ui
<br />I
<br />AND TO MAINTAIN PRO
<br />STANDARDS.
<br />0
<br />i
<br />CHIPS AND CRACKS.
<br />I ><
<br />11 I
<br />6.
<br />ALI NEW WALL MOUNTED 15, 20, AND 30 AMP OUTLETS/RECEPTACLES TO BE
<br />'
<br />i
<br />LLJ
<br />��
<br />31. PRIOR TO PAINTING, WALLS MUST BE PATCHED AND REPAIRED, CLEAN AND DRY
<br />7.
<br />DOOR HANDLES, PULLS OR KNOBS SHALL BE INSTALLED AT 40" ABOVE FINISH
<br />CENTERED AT +18" A.F.F., U.O.N.
<br />i
<br />�
<br />i 23.
<br />AT FLOOR AREAS SCHEDULED 1-0 RECEIVE NEW FLOOR COVERING, REMiOVE
<br />"I
<br />0�
<br />.
<br />ERED AND ALIGNED SO, AS TO LEAVE NO EVIDENCE OF
<br />FLOOR. ALL OTHER OPERABLE PARTS OF DOOR HARDWARE (SUCH AS DEADBOLTS,
<br />i
<br />EXISTING FLOOR COVERING AND PREPARE SUBSTRATE FOR NEW FLOOR COVERING
<br />0
<br />i
<br />PATCHING OR REPAIRS. ALL SCREW AND NAIL HEADS MUST BE SET AND
<br />KEYHOLES... ETC.) ARE TO BE CENTERED BETWEEN 34` AND 44" ABOVE FINISH
<br />7.
<br />ALL TELEPHONE AND DATA CABLE TO BE TEFLON COATED PLENUM RATED CABLE,
<br />PER SPECIFICATIONS AND MANUFACTURER'S REQUIREMENTS.
<br />3:
<br />SPACKLED. ALL JOINTS MUST BE TAPED AND COVERED WITH JOINT COMPOUND.
<br />FLOOR. IF EXISTING BUILDING STANDARD EXISTS, MATCH BUILDING STANDARD AND
<br />SUPPORTED INDEPENDENTLY FROM SUSPENDED CEILING SYSTEM. CABLI
<br />ry
<br />LLJ
<br />JOINTS THAT ARE FILLED TO BE SANDED SMOOTH AND DUST REMOVED PRIOR TO
<br />CE WITH ACCESSIBILITY REQUIREMENTS.
<br />SUPPLIED BY TENANT; ALL PULLS AND TERMINATIONS BY GENERAL CONTRACTOR.
<br />24.
<br />AT ABANDONED PENETRATIONS OF FIRE RATED WALLS, CEILING OR FLOOR
<br />=
<br />�_
<br />RECEIVING NEW PAINT FINISH APPLICATION.
<br />0
<br />CONSTRUCTION, COMPLETELY SEAL VOIDS WITH FIRE RATED MATERIAL TO FULL
<br />>_
<br />32. PRIOR TO PAINTING OVER WALL COVERING, SECURELY GLUE DOWN ANY LIFTING OR
<br />8.
<br />SPECIAL LOCKING DEVICES SHALL BE OF AN APPROVED TYPE.
<br />8.
<br />LOCATIONS OF FURNITURE POWER FEEDS SHALL ACCOMMODATE CIRCUITS AND
<br />THICKNESS OF THE PENETRATED ELEMENT. ALL PATCHING OF EXISTING WORK TO
<br />_711
<br />1
<br />BUCKLING AND HIDE ALL SEAMING OR BUMPS.
<br />WIRE PER ELECTRICAL DRAWINGS. TENANT SHALL BE RESPONSIBLE FOR
<br />REMAIN SHALL MATCH FINISH PER SCHEDULE OR WHERE UNSCHEDULED TO
<br /><
<br />9.
<br />PROVIDE WEATHER SEALS ON ALL EXTERIOR DOORS PER ANSI STANDARDS.
<br />PROVIDING FURNITURE POWER FEED, GENERAL CONTRACTOR SHALL INSTALL THE
<br />MATCH EXISTING FINISHES TO REMAIN, AND SHALL MEET OR EXCEED FIRE RATING
<br />77
<br />0
<br />33. WALLS TO HAVE AT LEAST ONE COAT OF COLORED PRIMER AND TWO COATS OF
<br />10.
<br />CONTRACTOR IS RESPONSIBLE TO COORDINATE & VERIFY ALL DOOR FRAME
<br />POWER FEED.
<br />INDICATED ON FLOOR PLAN AND AS REQUIRED BY THE FIRE/LIFE SAFETY
<br />c�
<br />Li
<br />SPECIFIED PAINT FINISH TYPE. PAINT TO BE A LOW VOC UNLESS U.O.N. HIGH
<br />THROAT THICKNESS' FOR EACH LOCATION.
<br />9.
<br />WHERE DEDICATED ELECTRICAL OUTLETS ARE NOTED WITHIN THE FURNITURE
<br />INSPECTOR.
<br />cn
<br />=)
<br />TRAFFIC/WEAR ABILITY WITH GOOD SCRUB AND CLEANING ABILITY. VERIFY ALL
<br />W W PRIOR TO PURCHASING PAINT.
<br />-10
<br />PANEL SYSTEM, THE PANEL SYSTEM SHALL ACCOMMODATE THIS REQUIREMENT.
<br />25.
<br />COORDINATE EXISTING SPRINKLER LINE AND HEAD LOCATION WITH NEW PLAN.
<br />I � ,I
<br />m
<br />11.
<br />ALL DOOR FRAMES BE FACTORY FINISHED, U.O.N..
<br />SUBMIT SPRINKLER SHOP DRAWINGS TO ARCHITECT FOR REVIEW WITH THE CITY
<br />I-
<br />34. PAINT ALL SPEAKER COVERS AND HVAC GRILLS IN GYPSUM BOARD WALLS AND
<br />10.
<br />A
<br />FLOOR OUTLETS ARE ACCEPTABLE NEXT TO SLIDING PANELS/WALLS AND OTHER
<br />FIRE DEPARTMENT.
<br />0
<br />=
<br />CEILINGS TO MATCH ADJACENT PAINT COLOR AS SPECIFIED.
<br />12.
<br />ALL WALL DOOR STOPS TO HAVE 2x6 BACKING IN THE WALL BEHIND.
<br />SPECIAL CONVENIENT LOCATIONS.
<br />11
<br />-i
<br />_�
<br />26.
<br />CONTRACTOR IS RESPONSIBLE FOR BUILDING SECURITY DURING DEMOLITION
<br />__j
<br /><
<br />35. PRIOR TO INSTALLING WALL TILES AND WALL BASE TILE, WALLS MUST BE
<br />13.
<br />MAXIMUM UNDERCUT OF ALL DOORS NOT IN A RATED CORRIDOR SHALL NOT
<br />11.
<br />WHERE ELECTRICAL WORK IS SPECIFIED IN CONJUNCTION WITH CABINET WORK,
<br />PHASE. PROTECT ALL OPENINGS FROM WEATHER CONDITIONS AND SECURE THEM
<br />=
<br />V)
<br />PATCHED AND REPAIRED, CLEAN AND DRY AND BE PROPERLY MEMBERED AND
<br />EXCEED 1/2" ABOVE FINISH FLOOR SURFACE.
<br />S ARE TO BE PROVIDED BY THE GENERAL CONTRACTOR.
<br />SM.
<br />1
<br />C�
<br />.
<br />ALIGNED, SO, AS TO LEAVE NO EVIDENCE OF PATCHING OR REPAIRS. ALL SCREW
<br />AND NAIL HEADS MUST BE SET AND SPACKLED. ALL JOINTS MUST BE TAPED AND
<br />14.
<br />CONTRACTOR SHALL REFINISH ANY BLEMISHED DOOR OR REPLACE SAID DOOR IF
<br />12.
<br />CUT-OUTS FOR SWITCHES, OUTLETS, ETC. AS REQUIRED BY THE CABINET
<br />27.
<br />DO NOT PERFORM ANY WORK THAT WILL VOID WARRANTIES OF EXISTING
<br />7�1
<br /><
<br />COVERED WITH JOINT COMPOUND. JOINTS THAT ARE FILLED ARE TO BE SANDED
<br />NOT ABLE TO REFINISH TO "AS NEW" CONDITION.
<br />BE COORDINATED WITH THE ELECTRICAL CONTRACTOR,
<br />R MOISTURE RESISTANT ELEMENTS WITHOUT PRIOR
<br />m
<br />:2E
<br />SMOOTH AND BUMP FREE WITH DUST REMOVED PRIOR TO RECEIVING MORTAR
<br />U.N.O. ALL RECEPTACLES WHERE MILLWORK OCCURS SHALL BE LOCATED PER
<br />APPROVAL FROM THE OWNER.
<br />0
<br />C)
<br />WALL TILES.
<br />15.
<br />ALL DOORS TO BE OPERABLE FROM THE INSIDE WITHOUT A KEY OR ANY SPECIAL
<br />ELEVATIONS OF THE MILLWORK ITEM IN QUESTION.
<br />-i
<br /><
<br />KNOWLEDGE OR EFFORT.
<br />28.
<br />ARCHITECT ASSUMES NO RESPONSIBILITY RELATING TO ANY TOXIC MATERIALS,
<br />:2
<br />36. ALL WALL TILES ARE TO HAVE A MORTAR BED/BOND COAT THICKNESS TO
<br />13.
<br />ALL WALL COVER PLATES SHALL BE WHITE, UNLESS BUILDING STANDARD IS
<br />INCLUDING ASBESTOS, AND ASSUMES NO RESPONSIBILITY TO ITS EXISTENCE OR
<br />w
<br />a:�
<br />16.
<br />ALL DOORS WITH ELECTRONIC SECURITY DOOR LOCKS MUST BE OPENABLE FOR
<br />DIFFERENT, MATCH BUILDING STANDARD.
<br />REMOVAL. THE OWNER WILL TAKE ACTION FOR DIRECTLY CONTRACTING WITH A
<br /><
<br />3�:
<br />ACCOMMODATE THE VARYING THICKNESSES OF ALL MATERIAL TYPES OF TILE
<br />EXITING PURPOSES UNDER ALL CONDITIONS. INCLUDING A POWER OUTAGE.
<br />I
<br />CIALIST, LICENSED BY THE STATE, FOR SUCH SERVICES
<br />SPECIFIED FOR WALL INSTALLATION WITH A FLUSH FRONT FACE.
<br />14.
<br />ALL SEPARATE CIRCUIT RECEPTACLES TO BE ORANGE COLOR WITH BUILDING
<br />�
<br />SHOULD THOSE SERVICES BE REQUIRED ON THE PROJECT.
<br />h
<br />0
<br />I
<br />�
<br />AIC
<br />ASS
<br />17.
<br />IF BUILDING STANDARDS ARE INCONSISTENT FOR DOORS, RELITES, HARDWARE,
<br />VER PLATE-
<br />. -
<br />v
<br />�_
<br />i
<br />.- - -
<br />37. ALL TRANSLUCENT GL� TILE SPECIFIED ARE TO RECEIVE UN�FORII c_rW.>"
<br />COVE
<br />-
<br />N TANDARD DETAILS, THEN CONTRACTOR
<br />29.
<br />IF THE EXISTING BUILDING CONSTRUCTION IS CLASSIFIED SUCH THAT
<br />=
<br />�, E5
<br />11
<br />BY BACK BUTTERING TILES AND TROWEL RIDGES FLATTENED PRIOR TO SETTING
<br />MUST VERIFY WITH DESIGNER AND OWNER PRIOR TO CONSTRUCTION.
<br />15.
<br />POWER/SIGNAL AND REFLECTED CEILING PLANS ARE FOR THE GENERAL
<br />I
<br />FIREPROOFING INSULATION IS PRESENT, THEN THE CONTRACTOR, PRIOR TO
<br />-
<br />�
<br />. 7-
<br />>_
<br />1
<br />TRANSLUCENT GLASS TILES.
<br />INFORMATION OF THE CONTRACTOR. EXACT LOCATIONS SHOULD BE VERIFIED.
<br />STARTING ANY WORK, SHALL VERIFY THE CURRENT FIRE -RESISTANCE RATING(S)
<br />0
<br />0
<br />38. FLOORS OF TOILETS, BATHING AND SHOWER ROOMS SHALL HAVE A SMOOTH,
<br />OF THE EXISTING BUILDING ELEMENT(S). IF THE EXISTING FIREPROOFING
<br />u
<br />I
<br />HARD, NONABSORBENT SURFACE. THE INTERSECTION OF SUCH FLOORS WITH
<br />16.
<br />TENANT TO PROVIDE AND INSTALL THE TELEPHONE AND DATA COM MUNI CATI ON
<br />INSULATION IS DAMAGED /AFFECTED DURING THE COURSE OF THE WORK, AS
<br />cn
<br />77
<br />WALLS SHALL HAVE A SMOOTH, HARD, NONABSORBENT VERTICAL BASE AS
<br />CABLING. CONTRACTOR TO COORDINATE SCHEDULING AND OTHER REQUIREMENTS
<br />DEFINED BY THIS PROJECT SCOPE, THEN THE CONTRACTOR SHALL PATCH/REPAIR
<br /><
<br />SPECIFIED IN FINISH PLANS OR RESTROOM ELEVATIONS. BASE SHALL EXTEND
<br />I
<br />WITH TENANT.
<br />THE FIREPROOFING INSULATION TO A CONDITION THAT SHALL MATCH OR EXCEED
<br />>_
<br />�__
<br />UPWARD ONTO THE WALLS NOT LESS THAN 4 INCHES.
<br />17.
<br />ALL/ANY CORE DRILL LOCATIONS SHALL BE VERIFIED WITH DESIGNER PRIOR 1-0
<br />THE ORIGINAL FIRE -RESISTANCE RATING(S) OF THE EXISTING BUILDING
<br />0:�
<br />LLJ
<br />0
<br />39. WALLS AND PARTITIONS WITHIN 2 FEET OF SERVICE SINKS, URINALS AND WATER
<br />DRILLING. ALL UNUSED CORE DRILLS SHALL BE PLUGGED AND CAPPED AS
<br />ELEMENT(S).
<br />0
<br />01-1
<br />CLOSETS SHALL HAVE A SMOOTH, HARD, NONABSORBENT SURFACE TO A HEIGHT
<br />REQUIRED TO MAINTAIN FLOOR FIRE RATING.
<br />30.
<br />CONTRACTOR TO RELOCATE AND REUSE EXISTING DOORS AND HARDWARE WHERE
<br />a_
<br />ui
<br />OF NOT LESS THAN 4 FEET ABOVE THE FLOOR.
<br />POSSIBLE.
<br />��
<br />-
<br />18.
<br />ALL TELEPHONE AND COMPUTER WIRES SHALL BE PULLED BY TENANT
<br />40. CONTROL JOINTS AT GYPSUM BOARD ASSEMBLIES: THE MAXIMUM RECOMMENDED
<br />CONTRACTOR U.O.N. ELECTRICAL CONTRACTOR SHALL PROVIDE PULL WIRES AND
<br />31.
<br />EXISTING DOORS TO REMAIN U.O.N.
<br />ll�
<br />n,
<br /><
<br />CONTROL JOINT SPACING FOR WALLS AND CEILINGS WITHOUT PERIMETER RELIEF IS
<br />TION.
<br />cf)
<br />30 LINEAR FEET OR 900 SQUARE FEET OF SURFACE AREA, WITH PERIMETER
<br />19.
<br />CONTRACTOR SHALL OBTAIN APPROVAL FROM ARCHITECT FOR ALL THERMOSTAT
<br />32.
<br />ALTERNATE CONSTRUCTION WASTE DISPOSAL- RECYCLING OF ACOUSTICAL TILES
<br />2:
<br />CD
<br />RELIEF IS 50 LINEAR FEET OR 2,500 SQUARE FEET OF SURFACE AREA. EXTERIOR
<br />�__
<br />JOINT SPACING IS RECOMMENDED AT 30 LINEAR FEET OR 900 SQUARE FEET OF
<br />I
<br />LOCATIONS.
<br />I
<br />I A.
<br />CEILING MATERIAL BEING RECLAIMED MUST BE KEPT DRY AND FREE FROM DEBRIS,
<br />�
<br /><
<br />u
<br />SURFACE AREA.
<br />�
<br />1 B.
<br />BEFORE DISPOSING OF CEILINGS, CONTACT THE ARMSTRONG RECYCLING CENTER
<br />Ll=
<br />0
<br />AT 877-276-7876, SELECT OPTION #4 TO TALK TO A CONSULTANT. THEY WILL
<br />Lli
<br />a-
<br />41. CONSTRUCTION JOINTS (EXPANSION JOINTS) AT GYPSUM BOARD ASSEMBLIES:
<br />VERIFY THE CONDITION OF THE MATERIAL AND THAT IT MEETS THE ARMSTRONG
<br />0
<br />CONSTRUCTION JOINTS ARE REQUIRED AT CONTINUOUS GYPSUM BOARD SURFACES
<br />�
<br />REQUIREMENTS FOR RECYCLING. CONSULTANT WILL PROVIDE ASSISTANCE TO
<br />r'l�
<br />WITH DISSIMILAR WALL STRUCTURE.
<br />I
<br />FACILITATE THE RECYCLING OF CEILING MATERIAL.
<br />,:7
<br /><
<br />I
<br />cf)
<br />CD
<br />=
<br />3:
<br /><
<br />cr_l
<br />n
<br />w
<br />�l V)
<br />I
<br />LLJ
<br />=
<br />I-
<br />l
<br />w
<br />______
<br />cn
<br />�
<br />__
<br />T__l
<br />-
<br />I
<br />=
<br />1
<br /><
<br />5;
<br />Ul
<br />=
<br />I
<br />1
<br />I
<br />I
<br />cn
<br />i
<br />I
<br />I
<br />I
<br />I
<br />I
<br />I
<br />i
<br />�
<br />w
<br />m
<br />"
<br />[a,
<br />I
<br />I j__
<br /><
<br />I
<br />�
<br />�
<br />I0
<br />z
<br />I
<br />I
<br />I
<br />I
<br />I
<br />_j
<br />I
<br />I
<br /><
<br />I I i
<br />Q�
<br />w
<br />3:
<br />Z
<br />L-i
<br />ui
<br />>
<br />Lij
<br />I
<br />0
<br />co
<br />V
<br />ry
<br />f__
<br />ct
<br /><
<br />---,-
<br /><
<br />�--
<br />M
<br />=
<br />]��
<br />I
<br />I
<br />�
<br />-
<br />LLJ
<br />iy
<br />LLj
<br />I I .
<br />. n,
<br />� ;
<br />I
<br />!
<br />:
<br />; -
<br />�
<br />- -
<br />I
<br />I
<br />j
<br />-
<br />,
<br />I ?�'
<br />i �
<br />I
<br />i
<br />I
<br />n
<br />Q:�
<br />Q,
<br />0
<br />1
<br />C)
<br />L�
<br />I
<br />__j
<br />cn
<br />LLJ
<br />D
<br />I
<br />i
<br />z
<br /><
<br />V)
<br />V)
<br />t
<br />I
<br />_j
<br />-
<br />�
<br />I
<br />N
<br />N
<br />(N
<br />C14
<br />1
<br />Lu
<br />0
<br />c�
<br />C)
<br />-�
<br />I
<br />�
<br />0,
<br />N
<br />*
<br />m
<br />!
<br />�
<br />I�
<br />�
<br />_:
<br />I
<br />I
<br />I
<br />__
<br />-
<br />i
<br />2
<br />El
<br />
|