Laserfiche WebLink
• <br /> JMTPOFB115 <br /> !IZ1 Fleece Thermo last Polyolefin Membrane <br /> Johns Manville p y <br /> Meets or exceeds the requirements of ASTM D 6878 <br /> Tested Physical Properties <br /> ASTM Standard for JM TPO FB 115' <br /> Physical Properties Test Method ASTM D 6878(Min.) MD* XMD** <br /> Breaking Strength,min,lbf(N) D 751 220(976) 499(2,220) 450(2,002) <br /> Elongation at Break,min% D 751 15 29 27 <br /> H Tearing Strength,min,lbf(N) D 751 45(200) 91(404) 146(649) <br /> Factory Seam Strength,min,lbf(N) D 751 66(290) 171(761) <br /> Thickness,min,in. D 751 +/-10%from Nominal 0.060(Nominal) <br /> d Thickness Over Scrim,min,in.(mm) D 7635 0.015 0.027(0.686) <br /> 3 Water Absorption,max,% D 471 3.0 0.08 <br /> Brittleness Point,max,-40°F D 2137 No Cracks Pass <br /> Properties after Heat Aging C@ 240°F D 573 Pass/Fail Pass <br /> Breaking Strength,%(after aging) D 751 90 >90 >90 <br /> o <br /> -e u <br /> 41 Elongation,%(after aging) D 751 90 >90 >90 <br /> I.@ Tearing Strength,%(after aging) D 751 60 >60 >60 <br /> to <br /> o. <br /> Weight Change,max,%(after aging) D 751 ±1.0 0.25 <br /> Linear Dimensional Change,max,%(after 6 hrs @158°F) D 1204 ±1.0 <0.2 <br /> Accelerated Weathering,min G 151&G 155 10,080 kj/mz•nm®340 nm 10,080 kj/mz <br /> (4,000 hrs CO 0.70 W) (4,000 hrs) <br /> ET, Cracking(@ 7x magnification) G 155 No Cracks Pass <br /> a. <br /> 1.JM TPO FB 115 is comprised of a 60 Mil TPO membrane and an integral fleece backing. <br /> The given physical properties are based on the JM TPO 60 Mil membrane. <br /> * MD=Machine Direction <br /> **XMD=Cross-Machine Direction <br /> Note:All data represents tested values. <br /> Supplemental Testing <br /> ASTM Standard for JM TPO—FB 115 <br /> Physical Properties Test Method ASTM D 6878(Min.) Result <br /> Dynamic Puncture D 5635 N/A Pass @ 27.5 Joules <br /> Static Puncture D 5602 N/A Pass CO 44 lb(20 kg) <br /> Reflectance C 1549 N/A 78% <br /> Eminence C 1371 N/A 0.87 <br /> Technical specifications as shown in this literature are intended to be All Johns Manville products are sold subjectto Johns Manville's standard <br /> used as general guidelines only.Please refer to the Safety Data Sheet Terms and Conditions,which includes a Limited Warranty and Limitation of <br /> and product label prior to using this product.The Safety Data Sheet Remedy.For a copy of the Johns Manville standard Terms and Conditions <br /> is available by calling(800)922-5922 or on the web at www.jm.com/ or for information on other Johns Manville roofing products and systems, <br /> roofing.The physical and chemical properties of the product listed herein visitwww.jm.com/terms-conditions. <br /> represent typical,average values obtained in accordance with accepted <br /> test methods and are subject to normal manufacturing variations.They <br /> are supplied as a technical service and are subject to change without <br /> notice.Check with the regional sales representative nearest you for <br /> current information. I 1 <br /> RS-8639 4-21(Replaces 2-18) <br />