33 SE EVERETT MALL WAY 2020 Plans 2022-10-24

I U Z Q 4N, POWER/ FURNITURE PLAN APPLIANCES: EQUIPMENT: ACCESSORIES: 3.1 COFFEE MAKER - PROVIDED AND INSTALLED BY TENANT 1.1 FLAT SCREEN -PROVIDED AND INSTALLED BY TENANT 1.6 MONEY MACHINE - PROVIDED AND INSTALLED BY TENANT 41 WASTE CAN - PROVIDED AND INSTALLED BY G.C. MFR: BUNN MFR: CUMMINGS - ALLISON MFR: RUBBER MAID MODEL: AIRPOT COFFEE BREWER - CWFT APS WITH AIRPOT 1.2 CASH RECYCLER - PROVIDED AND INSTALLED BY TENANT MODEL: MM2 - THROUGH WALL MODEL: SLIM JIM - RECYCLING CONTAINER NOTE: CONTRACTOR TO VERIFY POWER REQUIREMENTS. MFR: GLORY WIDTH: 26.8" MODEL NU: 1971258 MODEL: INTELLIGENT CASH RECYCLER DEPTH: 30.2" CAPACITY: 16 GALLONS MODEL M RBG-100 HEIGHT: 50" DIMS: 23-1/8" W X 11" D X 24-7/8" H WIDTH: 16-112" NOTE: CONTRACTOR TO VERIFY POWER/DATA REQUIREMENTS. COLOR: GRAY DEPTH: 38.7" HEIGHT: 46.3" 1.7 PDA6BU AMPLIFIER (UNDER COUNTER). PROVIDED AND INSTALLED BY GC 4 2 GROMMET - PROVIDED AND INSTALLED BY G.C. NOTE: CONTRACTOR TO VERIFY POWER/DATA REQUIREMENTS. MFR: DOUG MOCKETT MODEL: TRASH MANAGEMENT GROMMET - TM1C 1.3 CHANGE MACHINE - PROVIDED AND INSTALLED BY TENANT DIMS: 6" DIA. X 3" DEEP MFR: GLORY FINISH: SATIN STAINLESS STEEL (SSS) NOTE: CHANGE MACHINE SITS ON TOP OF COUNTER, CUSTOMER FACING. 4.3 GROMMET -PROVIDED AND INSTALLED BY G.C. 1.4 MOOD PROFUSION 10 VOLUME CONTROLLER - TOTAL OF TWO; (1) FOR OFFICE & MFR: DOUG MOCKETT (1) FOR LOBBY (UNDER COUNTER). PROVIDED AND INSTALLED BY GC MODEL: DESK GROMMET LINER - MM5A 1.5 NIGHT DROP- EXISTING, SCHEDULED TO REMAIN DIMS: 2-7/8" FINISH: SATIN CHROME (26D) NOTE: FIELD LOCATE 4.4 CASH TRAY - PROVIDED AND INSTALLED BY TENANT DIMS. 15 W X 15 D X 3-3/4"H POWER PLAN KEY NOTES: 1O NO WORK U.N.O. O PROVIDE AND INSTALL CONDUIT PATHWAY FOR ALARM SYSTEM TIED TO EQUIPMENT. ® IN ADDITION TO EQUIPMENT SHOWN IN PLAN, TELLER POD TO HOUSE THE FOLLOWING EQUIPMENT: (2) LAPTOPS, (2) MONITORS, (2) DOCKING STATIONS, (2) MONITOR ARMS, (1) CASH ADVANCE MACHINE, (2) RECEIPT PRINTERS, (2) SIGNATURE PADS, (2) CHECK SCANNERS, (2) INSTANT ISSUE PIN PAD AND (2) PHONES. G.C. TO ENSURE POWER AND DATA CAN SUPPORT EQUIPMENT. ® DESIGN BUILD CONTRACTOR VERIFY OWNER EQUIPMENT HEAT LOADS FOR POTENTIAL ADDITIONAL COOLING. O PROVIDE BACKING, POWER, DA AND AV IN WALL FOR OWNER FURNISHED DIGITAL MARKETING DISPLAY MONITOR. © GC SHALL PROVIDE A BIDDER DESIGNED AV SYSTEM. SYMBOLS LEGEND =0 DUPLEX RECEPTACLE DEDICATED DUPLEX RECEPTACLE ® VOICE/DATA RECEPTACLE. CONTRACTOR TO PROVIDE RIGID RACEWAY CONDUITS AND PULL STRING. REFER TO SECURITY & DATA DRAWINGS FOR MORE INFORMATION. TYP. cR PROXIMITY CARD READER ❑X - EQUIPMENT TAG ELECTRICAL NOTES: 1. FURNISH AND INSTALL ALL FIXTURES, ASSOCIATED TRIM AND FIXTURE LAMPS AS REQUIRED. ONLY NEW OUTLETS /FIXTURES ARE SHOWN, ALL EXISTING OUTLETS UNAFFECTED BY CONSTRUCTION ARE TO REMAIN AND ARE TO BE INTEGRATED INTO THE CURRENT SCHEME WHERE POSSIBLE. 2. SURVEY FIELD CONDITIONS AND VERIFY THAT WORK IS FEASIBLE AS SHOWN. VERI LOCATION OF ALL OUTLETS IN RELATION TO STRUCTURAL AND OTHER ELEMENTS REQUIRED. NOTIFY ARCHITECT IN WRITING OF ANY DISCREPANCIES BEFORE PROCEEDING WITH WORK. 3. ARCHITECTURAL DRAWINGS DETERMINE LOCATION AND TYPE (ARCHITECT TO VERIFY W/ ENGINEER) OF ALL OUTLETS AND TAKE PRECEDENCE OVER ALL OTHERS, U.N.O.. ELECTRICAL ENGINEER'S POWER PLAN SHALL GOVERN THE WIRING LAYOUT AND INSTALLATION IN COMPLIANCE WITH ALL LAWS APPLICABLE AND ENFORCED BY GOVERNING AUTHORITIES. 4. OUTLETS SHOWN BACK TO BACK ON PARTITION WALLS SHALL BE OFFSET 1'-0", MAXIMUM, OR MOUNTED AT DIFFERENT HEIGHTS IF INDICATED. 5. FURNITURE, IF SHOWN, IS FOR REFERENCE ONLY AND IS NOT IN CONTRACT, U.N.O. 6. COORDINATE ALL WORK RELATED TO EQUIPMENT WITH MANUFACTURER'S RECOMMENDATIONS, SPECIFICATIONS AND INSTRUCTIONS. 7. ALL EXISTING AND NEW FLOOR SLAB PENETRATIONS FOR CONDUIT OR PLUMBING LINES SHALL BE FULLY PACKED & SEALED IN ACCORDANCE WITH THE APPLICABLE BUILDING AND FIRE CODES. 8. COORDINATE NEW ELECTRICAL WITH EXISTING, WHERE OCCURS. 9. UPON COMPLETION OF OUTLET LAYOUT, NOTIFY THE ARCHITECT. ARCHITECT SF SITE VERIFY ALL OUTLET LOCATIONS PRIOR TO COMMENCEMENT OF CORING OR OUTLET INSTALLATION. 10. FURNISH AND INSTALL ONLY UNDERWRITERS LABORATORIES, INC. (UL) LABELLED DEVICES THROUGHOUT. 11. INSTALL WALL MOUNTED OUTLETS 18 INCHES ABOVE FINISHED FLOOR, U.N.O. HEIGHTS SHALL BE DETERMINED FROM FINISHED FLOOR TO THE CENTERLINE OF COVERPLATE, INSTALLED VERTICALLY, GROUNDING POLE AT BOTTOM, U.N.O. 12. MAINTAIN A 4-INCH HORIZONTAL CLEARANCE IN ALL DIRECTIONS, MIN. FROM EDGE COVERPLATE, FOR WALL MOUNTED OUTLETS, OR FROM EDGE OF MONUMENT FOR FLOOR MOUNTED OUTLETS, WHEN ADJACENT TO A WALL, COLUMN, OR SIMILAR ELEMENTS, U.N.O. 13. INDICATED DIMENSIONS ARE TO THE CENTER OF THE COVERPLATE OR MONUMENT; CLUSTERS OF OUTLETS ARE DIMENSIONED TO THE CENTER OF THE CLUSTER, U.N.O. GANG COVERPLATES SHALL BE ONE-PIECE TYPE, U.N.O. 14. ELECTRICAL SWITCH AND OUTLET COVER PLATES, SURFACE HARDWARE, ETC. SHALL BE INSTALLED AFTER PAINTING AND/OR APPLICATION OF WALLCOVERINGS & CARPEL SPECIFIED. 15. POWER/DATA/TELEPHONE REQUIREMENTS FOR OPEN OFFICE WORKSTATIONS TO BE PROVIDED WITH FURNITURE INSTALLATION DRAWINGS -BY OTHERS. 16. THE FURNITURE ELECTRICAL IS AN 8-WIRE SYSTEM. ALL ELECTRICAL FEEDS TO ANY OF THE PRODUCT MUST BE IN AN 8-WIRE CONFIGURATION. 17. "H" INDICATES THAT AN OUTLET SHALL BE MOUNTED HORIZONTALLY. 18. VERIFY NEW FLUSH FLOOR OUTLET LOCATIONS WITH FURNITURE LAYOUT PRIOR TO INSTALLATION. 19. ALL SWITCHES AND DIMMERS SHALL BE LOCATED 46" ABOVE FINISHED FLOOR TO CENTER OF SWITCH U.O.N.. MULTIPLE SWITCHES AT ONE LOCATION SHALL BE GANGED TOGETHER AND FINISHED WITH ONE COVER PLATE U.N.O. U"' w H s V a Sound Credit Union Everett 33 SE Everett Mall Way Everett, WA 98208 DESIGN JPC DRAWN AV, IVIS CHECKED TIP NO. 20-0316 1 1• 1 1 � 1 1 1 G ►� 6389 ► REGISTERED ARKA STATE OF Power and Equipment Plan 1-51 O 2018, JPC ARCF