1815 LOMBARD AVE 2023-04-11 - Laserfiche WebLink

.■ I S M SOLAR SON: MOUNT ------------------------------------------- BONDING MIDCLAMP ASSEMBLY BONDING CONNECTION GROUND PATHS i W INSTALLAT101"I buk : PAGE ------------------------------------------------------------- -----------------------------_-------- O FT ;_ BONDING MIDCLAMP ASSEMBLY Aluminum mid clamp with stainless steel bonding pins that pierce modute frame anodization to bond module to module through clamp Stainiess steel nut bonds aluminum ctamp to stainless steel T-bolt Serrated T-bolt head penetrates raiL anodization to bond T-bolt, nut, clamp, and modules to SM rail E � j___ SYS7M01.1110 e BONDING MIDCLAMP I(Irc otn ::iwrnoluu• A F.re Csvpry p+art Lk BONDING 'uranrwnrl to MICROINVERTER SOL1Q111" MOUNT QS-ste ' BONDING RAIL SPLICE BAR ��Bonding Hardware creates bond between spill, oar and —h rod section Aturn—m splice bar spans across rail gap to create rail to rail bond. Rail on at least one side of splice will be grounded BONDING MICROINVERTER MOUNT ©Nex nut -In t,,I- loll washer bends 1MJI microinverter flaNe to stainless steel T-bolt Serrated T Dolt Head penetrates rail anodization Q to bond T-bolt. nut, and L foot to grounded SM raa - RAILTO LFOOr . 0c,ING T.B RAILTO L-FOOTw/BONDINGT BOLT ©serrated flange nut removes L foot anadirat— to bond L-root to stainless steel T-tlplt 4 Serrated T-bolt head penevates rail arodizat- m bond T-bolt. nut, and L-loot to grounded SM rat E WEEBLUG (OR ILSCO LUG) RACK SYSTEM GROUND ©WEE8 washer dimples pierce anodized rail to create bond between rail and lint ©Solid copper wire connected to lug is routed to provide final system ground connection. ON: , SM SOLAR ENDCLAMP, FIRST MODULE:w MOUNT INSTALLATION -GUIDE-:- PAGE o o e 1✓ INSTALL MODULE END CLAMPS: The End clamp is supplied as an assembly with a 1/2' hex head bolt that is accessible at the ends of rails.The clamp should be installed on the rails prior to installing end modules. 1 INSTALL FIRST MODULE: Install the first end module onto rails with the flange of the module frame positioned between end clamps an ends of rails. 1 MEN==' INSTALL END CLAMPS ON RAIL: POSITION END CLAMPS: NOTE: To assist insertion of clamp into Slide end clamp on to rail by Slide end clamp assembly rail slot, Pressure may be applied to engaging the two t-guide brackets on to rail until bolt head top or side of bracket as shown. Do with the top slot of the rails. I I engages with end of rail not forte [lamp into rail by pushiilry bolt is extended as far as possiule End clamps are positioned on on bolt with excessive force so that clamp is positioned at max. rails prior to the first end distance from end of raiL module and prior to the last —dule. ENGAGE CLAMP: While holding module in position and with flange in full contact with rail, rotate end clamp bolt until clamp engages with flange to provide clamp force. To ensure bolt is not over -torqued, use low torque setting on drill or If using an impact driver, stop rotation as soon as impact action of driver begins. 7l:uUE VALUE .:nd notes on Per ziI End clamp bolt . 5 ft-lbs Net anti -seize 1 I 0- Ifs 112' For best appearance, position module Rush with ends of rails. Rails should not extend more `s than 1/2' beyond module. Module must be fully supported by rails and cannot overhang ends of rails. Lumio SMART ENERGY TODAY (SET) 1550 DIGITAL DR, LEHI, UT 84043, USA SYSTEM INFO (9) Q CELLS Q.PEAK DUO BLK ML-G10+ (400W ) (9) ENPHASE I108PLUS-72-2-US (240V) DC SYSTEM SIZE: 3.600 kWDC AC SYSTEM SIZE: 2.700 kWAC REVISIONS DESCRIPTION I DATE IREV PROJECT NAME & ADDRESS Q W O N 00 CSC Q O Q > O >� Q o z0 U 71- LU 04 Uj LU 00 LU 'IT cQ C Uj LU � Q Q 4e a Q Q 00 O J Lfi CID r DATE: 12/3/2022 SHEET NAME EQUIPMENT SPECIFICATIONS SHEET SIZE ANSI B 11" X 17" SHEET NUMBER PV-19