|
MICROINVERTER ilr
<br /> Use IronRidge's Microinverter Kit to bond compatible
<br /> microinverters and power optimizers to the racking system. one Microinverter
<br /> Kit Required
<br /> Insert Microinverter Kit T-bolt into top rail slot. Place (80 in-lbs)
<br /> compatible microinverter or power optimizer into position
<br /> and tighten hex nut to 80 in-lbs.
<br /> ➢ If installing in areas with ground snow loads greater than 40 psf,
<br /> install MLPE devices directly next to module frame edge
<br /> COMPATIBLE PRODUCTS ------------------
<br /> Enphase
<br /> M250-72,250-60,M215-60,C250-72,S230,S280, IQ 6,IQ 6+,IQ
<br /> IQ7,IQ 7A,IQ 7+,IQ7 PD, IQ 7X,Q Aggregator; IQ8-60, _
<br /> IQ8PLUS-72,IQ8A-72,IQ8H-208-72,IQ8H-240-72,IQ8M-72,may be
<br /> followed by-2-US
<br /> Darfon
<br /> MIG240,MIG300,G320,G640
<br /> Solar Edge
<br /> M1600, P300, P320,P340, P370,P400,P401, P405,P485, P505,
<br /> P600, P700, P730,P750, P800p,P800s,P801, P850,P860,P950,
<br /> P960, P1100, P1101,S440,S500,S1200,S1201
<br /> SMA
<br /> RoofCommKit-P2-US,TS4-R Module Retrofit Kits(TS4-R-S,TS4- _
<br /> R-O,TS4-R-F)
<br /> On AP systems equipment,
<br /> Tlgo remove Grounding Washer
<br /> Tigo Access Point(TAP)
<br /> TS4-R-X(where X can be F,M,O,or S)
<br /> TS4-R-X-DUO(where X can be M,O,or S)
<br /> TS4-A-X(where X can be F,2F,O,O-DUO,or S) Al
<br /> l
<br /> Generac
<br /> S2502 Two icroinverter
<br /> - - - -- _ - Kits Required
<br /> in-lbs)
<br /> AP Systems
<br /> DS3,QS1,QT2 and YC600
<br /> NEP
<br /> BDM-300,BDM-300X2 and BDM-800
<br /> ➢ Remove Grounding Washer on AP Systems QS1,QT2, DS3 and YC600 inverters before installing to XR rails.
<br /> ➢ Remove the Stainless Steel Clip on Tigo-"A"MLPE Devices before attaching to XR rails.
<br /> ➢ Use the number of Iron Ridge Microinverter kits allowed by the MLPE mounting flange.Some will require 1
<br /> kit and others 2 kits.
<br /> Ak
<br /> IronRidge systems using approved Enphase products or SunPower modules eliminate the need for lay-in lugs and field
<br /> installed equipment grounding conductors (EGC). This solution meets the requirements of UL 2703 for bonding and
<br /> grounding and is included in this listing.
<br /> COMPATIBLE PRODUCTS
<br /> Sunpower
<br /> Modules with model identifier Ab-xxx-YY and InvisiMount(G5)46mm frame;where"A"is either E,or X; "b"can be 17, 18,19,20,21,or 22;
<br /> and"YY"can be C-AC,D-AC,BLK-C-AC,or BLK-D-AC.
<br /> Enphase
<br /> Microinverters M250-72,M250-60,M215-60,C250-72,and Engage cables ETXX-240,ETXX-208, ETXX-277.
<br /> ➢ A minimum of two inverters mounted to the same rail and connected to the same Engage cable are required.
<br /> ➢ The microinverters or Sunpower AC modules must be used with a maximum 20 A branch rated overcurrent protection device(OCPD).
<br /> ➢ If an AC module is removed from a circuit for maintenance,you must first disconnect AC power and then install a temporary EGC to
<br /> bridge the gap by inserting an AC extension cable(or via other NEC-compliant means), in order to maintain effective ground continuity
<br /> to subsequent modules.
<br />
|