Laserfiche WebLink
AISI SPECIFICATION PROVISIONS for SCREW CONNECTIONS <br />NOTATION SCREW PROPERTIES GAUGE METAL THICKNESS <br />Number Nominal Gauge Thickness <br />d = nominal screw diameter <br />Designation Dia., d, in. (in. ) <br />dw = the larger of the screw head or washer <br /># 2 0.0860 25 ga. 0.019 <br />diameter, but not larger than 1/2"(5/16"MIN.) <br /># 3 0.0990 22 ga. 0.028 <br />FS = factor of safety = 3.0 <br /># 4 0.1120 20 ga. 0.035 <br />Pas = allowable shear force per screw <br /># 5 0.1250 18 ga. 0.045 <br />Pns = nominal shear strength per screw <br /># 6 0.1380 16 ga. 0.057 <br />Pat = allowable tension force per screw <br /># 7 0.1510 14 ga. 0.071 <br />Pit= nominal tension strength per screw <br /># 8 0.1640 12 ga. 0.102 <br />Ppot = pull-out force per screw <br /># 10 0.1900 Fu =45ksi min. <br />Ppov = pull -over force per screw <br /># 12 0.2160 <br />t, = thickness of member in contact <br />1/4 in. 0.2500 <br />with the screw head <br />NOTE:- <br />t2 = thickness of member not in contact <br />1.) Screw sizes smaller than # 2 or larger than 1/4" <br />with the screw head <br />are not to be used. <br />Fw = tensile strength of member in contact <br />2.) The tested shear capacity of the screw shall not <br />with the screw head <br />be less than 1.25 Pns = 3.75 Pas. <br />FU2 = tensile strength of member not in <br />3.) The tested tension capacity of the screw shall not <br />contact with the screw head <br />be less than 1.25 P„t = 3.75 Pat. <br />E6.3 Shear E6.4 Tension <br />Pas = P n5/3 Pat = P nt/3 <br />For t2/t, <=1.0 Pas shall be taken as the smaller of Pat shall be taken as the smaller of <br />Pas = 1.4 (t23 d)'12F.2 Pull - Out <br />Pas = 0.9 t, d F,,, Pat = 0.283 t2 d Fu2 <br />Pas = 0.9 t2 d Fu2 Pull - over <br />Pat = 0.5 t, dw Fu, <br />For t2/t, >=2.5 Pas shall be taken as the smaller of <br />Pas = 0.9 t, d FU, <br />Pas = 0.9 t2 d F.2 <br />For 1.0< t2/t, <2.5 Pas shall be determined by the <br />linear interpolation between the above two cases <br />Al 1 n1A/API G 1 nuns rlhc 1 <br />SCREW <br />SIZE <br />GAUGE <br />#12 <br />d = 0.216 <br />#10 <br />d = 0.190 <br />#8 <br />d = 0.164 <br />#6 <br />d = 0.138 <br />SHEAR <br />PULL-OUT <br />SHEAR <br />PULL-OUT <br />SHEAR <br />PULL-OUT <br />SHEAR <br />PULL-OUT <br />25 <br />75 <br />52 <br />71 <br />46 <br />66 <br />39 <br />60 <br />33 <br />22 <br />139 <br />78 <br />131 <br />69 <br />1 121 <br />59 <br />111 <br />50 <br />20 <br />188 <br />95 <br />177 <br />84 <br />164 <br />72 <br />151 <br />61 <br />18 <br />280 <br />124 <br />263 <br />109 <br />244 <br />94 <br />224 <br />79 <br />16 <br />394 <br />156 <br />370 <br />137 <br />344 <br />118 <br />315 <br />100 <br />14 <br />557 <br />196 <br />523 <br />173 <br />474 <br />149 <br />398 <br />125 <br />12 <br />890 <br />280 <br />783 <br />246 <br />675 <br />213 <br />568 <br />179 <br />Min. Edge <br />Dist. and <br />o/c Spacing <br />11/16 in. <br />9/16 in. <br />1/2 in. <br />7116 in. <br />SCREWS TO HAVE 5116" MINIMUM HLAU UTAMr- i CK. <br />L776 <br />