Laserfiche WebLink
REQUIRED NUMBER AND LOCATION OF MODEL REQUIRED NUMBER AND LOCATION OF MODEL <br /> . . •1100"V" SERIES BRACES FOR 4/12&5/12 1100"V" SERIES BRACES FOR 6/12&7/12 <br /> • <br /> SINGLE SECTION DOUBLE WiDES TRIPLEYIDES SINGLE SECTION DOUBLE WIRES TRIREMES <br /> 0,.. ,—i I ._I:. - r - ..�.� . t lei. :. :: 13— -E B :.t;. ::L: 1'3 ' --H 1 : <br /> 3 B -- :I: g i--� Iv I i.- 1,_ --PI -f B <br /> - <br /> SINGLE SECTION DOUBLE WIRES AU.WIDTHS DOUBLE WOES ALL WIDTHS SINGLE SECTION DOUBLE WIRES ALL WIDTHS DOUBLE WOES AU.WIDTHS <br /> ALL WIDTHS up to 76' up to 76' ALL WIDTHS up to 76' up to 76' <br /> up to 76' up to 76' <br /> LEGEND: (Length of house is actual box size) <br /> 1.- .: . - Approximate location of the system(See note H) <br /> 2.-K3- - Location of ASF Model 1100"V" (Lateral and Longitudinal Bracing)or 1100 T(Lateral only) <br /> 3.-0— - Location of additional ASF Model 1100 T`V"System(Lateral only)for homes exceeding 76'in length or with roof pitch between 4.37/12(20 degrees) <br /> and 5/12,the additional system is to be installed at approximately the midpoint of the house and may be installed at either exterior beam. <br /> 4.- ® - Installation of single wide homes require two(2)anchors per side located not more than ten(10)feet from each end(with a minimum of 3150 load rating <br /> 5.- : -- - Location of additional ASF Model 1100 T"V"System(Lateral only)for homes exceeding 78'in length,sidewall height exeeding 96"or with roof pitch <br /> between 6/12&7/12 the additional system is to be installed at approximately the midpoint of the house and may be installed at either exterior beam. <br /> NOTE: <br /> a) Installation of the longitudinal system eliminates the need for the longitudinal anchors. <br /> b) installation of the transverse system eliminates the need for all anchors,diagonal frame ties and stabilization plates exc ept when noted. <br /> (Legend#5&note C) <br /> c) All other home manufacturer's instructions for installation of stabilizing devices must be followed, including installation of vertical tie-down <br /> anchors,and mating line column, shear wall or center-line tie-down anchors.NOTE WIND ZONE II: ALL VERTICAL ANCHORS(NOT TO <br /> EXCEED 8'SPACING)MUST BE INSTALLED PER MANUFACTURER'S INSTALLATION INSTRUCTIONS! <br /> d) If the home manufacturer's installation instructions are not available,the home must be installed in accordance with any state promulgated <br /> rules or as required by the authority having jurisdiction. <br /> e) if bolts,nuts and tech screws are lost,they may be replaced as long as they meet or exceed the specs for Oil ASFS hardware. <br /> f) When the length of home exceeds 76',sidewall height exceeds 96"or the roof pitch Is between 4.37/12(20 degrees)and 5/12,add 1 transverse system <br /> (see location diagrams above)6/12:a total of 4 Transverse&3 Longitudinal systems are needed&7/12:a total of 5 Tra nsverse&3 Longitudinal systems i <br /> are needed. (Longitudinal portion only required when longitudinal bracing Is required by home manufacturer). <br /> g) An alternative method using the 1100 CVO anchors(dry set)or 1100 CVW(wet set)may be used on a footing size of 16'diam eter X 24"depth.These <br /> brackets are designed for lateral and longitudinal protection. <br /> h) It is recommended that the systems be Installed at the 2nd pier In from each end of the house. However,they may be Insta lied at any location at least <br /> 2 feet,but not more than 14 the house length,in from the ends of the home. <br /> STATE OF MICHIGAN ONLY: As required by Section 1805.2 of the 200 Michigan Building Code.the depth of the Tooter shall be a minimum depth of <br /> 42 inches below grade.except that the authority having jurisdiction may approve a lesser depth based on known prevailing soil and weather <br /> conditions,or as provided by the exception under Section 1805.2.1 of the Code. <br /> STATE OF ALABAMA ONLY: Maximum pier height is limited to 32"with pier defined <br /> in the Alabama Regulation as'that portion of the support system between the top of <br /> the footing and the bottom of the pier cap." <br /> The State of Alabama limits the use of this <br /> i•• <br /> system to H.U.D labeled homes <br /> STATE OF NORTH CAROLINA ONLY: <br /> - <br /> Tubing must be galvanized and,when I-Transverse Arm,I-Beam Connector 3111;the manufacturer's installation <br /> instructions are not available, <br /> vertical wall tie-downs must be <br /> installed not to exceed 8-feet <br /> on center. (Wind Zone II) F-"V"Brace I-Beam <br /> STATE OF IDAHO ONLY: �,� <br /> Concrete must be a -I H-Transverse Arm Connectors <br /> 00.1 <br /> minimum of 8"in depth Top(1.25'� <br /> Bottom(1.5') iiiir <br /> ------....„............- _.4A/110,40 <br /> Ay IL 11 <br /> ''#.0 TECHNOLOGIES INC. <br /> 0 D-Pan Transverse Connector E-"V"Brace Tube <br /> or D(W)or D(D)Concrete _ (1.51) <br /> Phone:(=oo)284-7437 Transverse Connector lip r. • iiir <br /> Fax:(931)796-8611 A, <br /> oilvertechnolog es.com i <br /> 41110 <br /> 467 Swan Avenue,Hohenwald,TN 38462 B-Ground Pan or =- <br /> C-Concrete Base(le J- Pan V Bracket or <br /> Tooter,runner,etc.) ir J(W)or J(D)Concrete <br /> Bracket <br /> Ramlea l M/1 7/o1M PATFNT 4 M 141 Si)and nthpr nAh°ntc npnriinn Dana l/1 <br />