Laserfiche WebLink
ESR-4143 I Most Widely Accepted and Trusted Page 29 of 82 Page 17 of 20 <br />Adhesive anchoring system for rehar and anchor fastenings. <br />For use in hollow and solid masonry of day bride, concrete block and mule wylhe wall. <br />Had HIT-1IT 270 <br />Contains: methacrylates, dibenzoyl peroxide, boric add <br />000 <br />Danger <br />H315 <br />Causes skin initation.(A) <br />H317 <br />May cause an allergic skin reaction.(A,B) <br />H319 <br />Causes serious eye initatlon.(A) <br />H360 <br />May damage fertility or the unborn chid.(A) <br />H400 <br />Very toxic to aquatic Itte (B) <br />H412 <br />Harmful to aquatic life with long lasting effects.(A) <br />P262 <br />Do rat get in eyes, on skin, or on clothing. <br />P280 <br />Wear protective gloves/protective clothing/eye protectionflace protection. <br />P302+P352 <br />IF ON SKIN: Wash with plenty of soap and water. <br />P305+P351+P338 <br />IF IN EYES: Rinse cautiously with water for several minutes. Remove contact <br />lenses, it present and easy a do. Continue dosing. <br />P333+P313 <br />If skin irritation or rash occurs: Get medical advice/attention. <br />Disposal considerations <br />Empty packs: <br />► Leave the mixer attached and dispose of via the local Green Dot recovery system or EAK waste material <br />code: 150102 plastic packaging <br />Full or partially emptied packs: <br />► Must be disposed of as special waste in accordance with official regulations. <br />EAK waste material code: 08 04 09' waste adhesives and sealants containing organic solvents or other dangerous <br />substances. or EAK waste material code: 20 01 27' paint, inks, adhesives and resins containing dangerous <br />substances. <br />Warranty: Refer to standard Hihi tens and conditions of sale for warranty information <br />Failure to observe these installation instructions, use of non-Hil6 anchors, poor or questionable base material <br />'-..bins, or unique applications may affect the reliability or performance of the fastenings. <br />Product Information <br />- Always keep these instructions together with the product even when given to other persons. <br />- Check expiration date: See imprint on foil pack manifold f month/year). Do not use expired product. <br />- Foil pack temperature during usage: between 41 of and 104 °F /+5 oC and 40 T. <br />- Base material temperature at time of installation: between 23 of and 104 of /-5 oC and 40 T. <br />Exception In hollow, solid and mum-wythe solid clay brtcle between 41 T and Ill /+SoC and 40oC. <br />- Conditions for transport and storage: Keep in a cool, dry and dark place between 41 of and 77 of / <br />ST and 25oC. <br />- For any application not covered by this document / beyond values specified, please contact Hilti. <br />- Partly used foil packs must remain in the cassette and has to be used within 4 weeks. Leave the mixer <br />attached on the foil pack manifold and store within the cassette under the recommended storage condi- <br />tions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive. <br />A NOTICE <br />A Improper handling may cause mortar splashes. <br />- Always wear safety glasses, gloves and protective clothes during installation. <br />- Never start dispensing without a mixer properly screwed on. <br />- Attach a new mixer prior to dispensing a new foil pack (ensure snug fit). <br />- Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not modify the mixer in any <br />way. <br />- Never use damaged foil packs ancl/or damaged or unclean foil pack holders (cassettes). <br />A Poor load values / potential failure of fastening points due to Inadequate borehole cleaning. <br />- The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants prior to <br />adhesive injection. <br />- For blowing out the borehole - blow out with oil free air until return air stream is free of noticeable <br />dust. <br />- For brushing the borehole - only use specified wire brush. The brush must resist insertion into the <br />borehole - if not the brush is too small and must be replaced. <br />A Borehole filling In solid masonry: Ensure that boreholes are filled from the back of the borehole without <br />forming air voids. If necessary use the accessories / extensions to reach the back of the borehole. <br />A Borehole filling In hollow masonry: Use a mesh sleeve. Fill the mesh sleeve with mortar from the <br />centering cap until mortar escapes at the centering cap (filling control). <br />A MufiFWythe Solid Brick application: HIT -SC sieve sleeves / sieve sleeve combinations have to be Blled <br />outside the bore hole: Push the mixer to the bottom of the last mesh sleeve (use mixer extension if <br />necessary),Inject the anchor adhesive starting at the bottom of the last mesh sleeve while slowly with- <br />drawing the mixing nozzle towards the centering cap, step by step, after each pull of the bigger. HIT -SC <br />sieve sleeves have to be filled completely without forming air voids until anchor adhesive escapes at the <br />centering cap (filling control). <br />A Not adhering to these setting Instructions can result In failure of fastening polntsl <br />HAS ®® <br />HIS <br />Rebar <br />I <br />OD <br />ill <br />on <br />�► Ill +J� <br />MD 2500 <br />HDM <br />�y ED 3500-A <br />) HIDE 500-A <br />C� <br />WW <br />330ml/11.1 f1.oz: 2x <br />500ml 16.9f1.oz: 3x <br />d <br />`. her <br />t. <br />•t � yyy <br />y <br />7 <br />FIGURE 5—MANUFACTURERS PRINTED INSTALLATION INSTRUCTIONS (CONTINUED) <br />