Laserfiche WebLink
29 of 32 <br />ESR-4143 I Most Widely Accepted and Trusted Page 17 of 20 <br />Adhesive anchoring system for rehar and anchor fastenings. <br />For use in hollow and solid masonry of Gay brick, concrete block and multi wythe wall. <br />N fil HITaW 270 <br />Co rtaftw: methacrylates, dithenzayl peroxide, boric acid <br />O®0 <br />IA.e) (A) IBI <br />Dania <br />H315 Causes skin initatlon.(A) <br />H317 May cause an allergic slan reactioa(A,B) <br />H319 Causes serious eye inifation.(A) <br />H360 May damage fertility or the unborn chid.(A) <br />H400 Very toxic to aquatic life (B) <br />H412 Harmful to aquatic life with long lasting effects.(A) <br />P262 Do not get in eyes, on skin, or on clothing. <br />P280 Wear protective gloves/protective clothing/eye protection/face protection. <br />P302+P352 IF ON SKIN: Wash with plenty of soap and water. <br />P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact <br />lenses, it present and easy to do. Continue timing. <br />P333+P313 If skin irritation or rash occurs: Get medical advice/attention. <br />Disposal considerations <br />Empty packs: <br />► Leave the mixer attached and dispose of via the kxal Green Dot recovery system 16 or EAK waste material <br />code: 150102 plastic packaging <br />Full or partially emptied packs: <br />► Must be disposed of as special waste in accordance with official regulations. <br />EAK waste material code: 08 04 09' waste adhesives and sealants containing organic solvents or other dangerous <br />substances. or EAK waste material code: 20 01 27' paint, inks, adhesives and resins containing dangerous <br />substances. <br />Waeanq: Refer to standard Him terms and cenditions of sale for warranty information <br />Failure to observe these installation instructions, use of rwn-HiIA anchors, poor or questionable base material <br />conditions, or unique applications may affect the reliability or performance of the fastenings. <br />Product Information <br />— Always keep these instructions together with the product even when given to other persons. <br />— Check expiration date: See imprint on foil pack manifold (month/yeri Do not use expired product. <br />— Foil pack temperature during usage: between 41 of and 104'F /+5 oC and 40 T. <br />— Base material temperature at time of installation: between 23 of and 104 of /-5 oC and 40 T. <br />Exception In hollow, solid and muttl-wythe solid clay brick: between 41 of and 104'F /+5'C and 40'C. <br />— Conditions for transport and storage: Keep in a cool, dry and dark place between 41 of and 77 of / <br />5oC and 25'C. <br />— For any application not covered by this document / beyond values specified, please contact Hilti. <br />— Partly used foil packs must remain in the cassette and has to be used within 4 weeks. Leave the mixer <br />attached on the foil pack manifold and store within the cassette under the recommended storage condi- <br />tions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive. <br />A NOTICE <br />A Improper handling may cause mortar splashes. <br />— Always wear safety glasses, gloves and protective clothes during installation. <br />— Never start dispensing without a mixer properly screwed on. <br />— Attach a new mixer prior to dispensing a new foil pack (ensure snug fit). <br />— Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not modify the mixer in any <br />way. <br />— Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes). <br />A Poor load values / potential failure of fastening points due to Inadequate borehole cleaning. <br />— The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants prior to <br />adhesive injection. <br />— For blowing out the borehole — blow out with oil free air until return air stream is free of noticeable <br />dust. <br />— For brushing the borehole — only use specified wire brush. The brush must resist insertion into the <br />borehole — if not the brush is too small and must be replaced. <br />A Borehole filling In solid masonry: Ensure that boreholes are filled from the back of the borehole without <br />forming air voids. If necessary use the accessories / extensions to reach the back of the borehole. <br />A Borehole Oiling In hollow masonry: Use a mesh sleeve. Fill the mesh sleeve with mortar from the <br />centering cap until mortar escapes at the centering cap (filling control). <br />A MuBFWythe Solid Brick application: HIT -SC sieve sleeves / sieve sleeve combinations have to he filled <br />outside the bore hole: Push the mixer to the bottom of the last mesh sleeve (use mixer extension if <br />necessary). Inject the anchor adhesive starting at the bottom of the last mesh sleeve while slowly with- <br />drawing the mixing nozzle towards the centering cap, step by step, after each pull of the bigger. HIT -SC <br />sieve sleeves have to be filled completely without forming air voids until anchor adhesive escapes at the <br />centering cap (filling control). <br />A Not adhering to these setting instructions can result In failure of fastening polntsl <br />_ 111"nal HAS <br />® HIS <br />000 <br />--api com M� <br />ID 2500 <br />HDM <br />�y ED 3500-A <br />HIDE 500-A <br />330m1/11.1B.oz:2x <br />510ml116.9B.oz: 3x <br />FIGURE 5—MANUFACTURERS PRINTED INSTALLATION INSTRUCTIONS (CONTINUED) <br />