8205 FLORIDA DR 2023-10-19 - Laserfiche WebLink

GENERAL NOTES AERIAL VIEW CODE AND STANDARDS 1.ALL WORK SHALL COMPLY WITH 2017 NATIONAL ELECTRIC CODE(NEC),2015 INTERNATIONAL BUILDING CODE . BLUE RAVEN (IBC),2015 INTERNATIONAL RESIDENTIAL CODE(IRC),2015 INTERNATIONAL PLUMBING CODE(IPC),AND ALL STATE . ~". j AND LOCAL BUILDING,ELECTRICAL,AND PLUMBING CODES. N 2.DRAWINGS HAVE BEEN DETAILED ACCORDING TO UL LISTING REQUIREMENTS. ; t 1403 N. Research Way SITE NOTES/OSHA REGULATION Orem, UT 84097 1.A LADDER SHALL BE IN PLACE FOR INSPECTION IN COMPLIANCE WITH OSHA REGULATIONS. 800.377.4480 2.THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS A UTILITY INTERACTIVE SYSTEM. WWW.BLUERAVENSOLAR.COM 3.THE SOLAR PV INSTALLATION SHALL NOT OBSTRUCT ANY PLUMBING,MECHANICAL,OR BUILDING ROOF VENTS. 4.ROOF COVERINGS SHALL BE DESIGNED,INSTALLED,AND MAINTAINED IN ACCORDANCE WITH THIS CODE AND CONFIDENTIAL-THE INFORMATION THE APPROVED MANUFACTURER'S INSTRUCTIONS SUCH THAT THE ROOF COVERING SHALL SERVE TO PROTECT t HEREIN CONTAINED SHALL NOT BE THE BUILDING OR STRUCTURE. USED FOR THE BENEFIT OF ANYONE EXCEPT BLUE RAVEN SOLAR NOR SHALL IT BE DISCLOSED IN WHOLE OR SOLAR CONTRACTOR - IN PART TO OTHERS OUTSIDE 1.MODULE CERTIFICATIONS WILL INCLUDE UL1703,IEC61646,IEC61730. RECIPIENTS ORGANIZATION,EXCEPT 2.IF APPLICABLE,MODULE GROUNDING LUGS MUST BE INSTALLED AT THE MARKED GROUNDING LUG HOLES PER IN CONNECTION WITH THE SALE AND THE MANUFACTURER'S INSTALLATION REQUIREMENTS. USE OF THE RESPECTIVE EQUIPMENT, 3.AS INDICATED BY DESIGN,OTHER NRTL LISTED MODULE GROUNDING DEVICES MAY BE USED IN PLACE OF ` WITHOUT THE WRITTEN PERMISSION STANDARD GROUNDING LUGS AS SHOWN IN MANUFACTURER DOCUMENTATION AND APPROVED BY THE AHJ. �# OF BLUE RAVEN SOLAR LLC. 4.CONDUIT AND WIRE SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND ARE NOT MEANT TO LIMIT UP-SIZING AS REQUIRED BY FIELD CONDITIONS. 5.CONDUIT POINT OF PENETRATION FROM EXTERIOR TO INTERIOR TO BE INSTALLED AND SEALED WITH A . NAB C E P SUITABLE SEALING COMPOUND. 6.DC WIRING LIMITED TO MODULE FOOTPRINT W/ENPHASE AC SYSTEM. • CERTIFIED 7.ENPHASE WIRING SYSTEMS SHALL BE LOCATED AND SECURED UNDER THE ARRAY W/SUITABLE WIRING CLIPS. �\ • i V , I I V� 8.MAX DC VOLTAGE CALCULATED USING MANUFACTURER PROVIDED TEMP COEFFICIENT FOR VOC UNLESS NOT I , ` � —'.� G PV INSTALLATION AVAILABLE. 9.ALL INVERTERS,MOTOR GENERATORS,PHOTOVOLTAIC MODULES,PHOTOVOLTAIC PANELS,AC ♦ `r �_ a PROFESSIONAL PHOTOVOLTAIC MODULES,DC COMBINERS,DC-TO-DC CONVERTERS,SOURCE CIRCUIT COMBINERS,AND O Scott Gurney CHARGE CONTROLLERS INTENDED FOR USE IN A PHOTOVOLTAIC POWER SYSTEM WILL BE IDENTIFIED AND .' ' , #PV-011719-015866 LISTED FOR THE APPLICATION PER NEC 690.4(B). ,• �'► �� 10.ALL SIGNAGE TO BE PLACED IN ACCORDANCE WITH LOCAL BUILDING CODE. CONTRACTOR: 11.TERMINALS AND LUGS WILL BE TIGHTENED TO MANUFACTURER TORQUE SPECIFICATIONS(WHEN PROVIDED) .� IN ACCORDANCE WITH NEC CODE 110.14(D)ON ALL ELECTRICAL CONNECTIONS. ` 1 BRS FIELD OPS Sealed For 800-377-4480 EQUIPMENT LOCATIONS • �. Existing Roof& 1.PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED AS PER SECTION NEC 110.26. Attachment Only 2.EQUIPMENT INSTALLED IN DIRECT SUNLIGHT MUST BE RATED FOR EXPECTED OPERATING TEMPERATURE AS i SPECIFIED BY NEC 690.31(A)AND NEC TABLE 310.15(B). 1 3.ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL ACCORDING TO NEC 1/ ! U U APPLICABLE CODES. Z Q 4.ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED FOR OUTDOOR USAGE WHEN APPROPRIATE. PROJECT INFORMATION: ��. p �, 00 LO NUMBER OF STORIES: 1 ` Z. 0 LU LU CONDUIT RUN: Interior _ r j LL > - NN ECOBEE QTY: 1 � 44056 � � cin � � LIGHT BULB QTY: 18 PV METER: Not Required DESIGN CRITERIA SITE SPECIFICATIONS SHEET INDEX �Fcisr> �v �`�� w H H ROOF TYPE (1) INFORMATION: �SSlOHAt F..4%% O Y O U) N WIND SPEED: 110 mph CONSTRUCTION -V-B PV1 -COVER SHEET W LL "- N >- ROOF TYPE: Comp Shingle GROUND SNOW LOAD: 25 Ib/ft2 ZONING: RESIDENTIAL PV2-SITE PLAN N X Ln FRAMING TYPE: Manufactured Truss WIND EXPOSURE FACTOR: C PV3- ROOF PLAN N > V U SHEATHING TYPE: PLYWOOD V Q oo W Q SEISMIC DESIGN CATEGORY: D PV4-STRUCTURAL ATTACHMENT: SFM Infinity Switchblade Flashkit 1/18/2023 C RACKING: Unirac SFM Infinity @ 48" OC Portrait/72"OC Landscape PV5- ELECTRICAL LINE DIAGRAM NUMBER OF ATTACHMENTS: 46 SCOPE OF WORK PV6- ELECTRICAL CALCULATIONS DRAWING BY: PV7-WARNING LABELS AND LOCATIONS Tia Bradley ROOF TYPE (2) INFORMATION (IFAPPLICABLE): INSTALLATION OF UTILITY INTERACTIVE PHOTOVOLTAIC SOLAR SYSTEM AND ANY (ALL OTHER SHEETS AS REQUIRED) Digitally signed by *SEE PV4.2 NECESSARY ADDITIONAL WORK NEEDED FOR INSTALLATION. SS- PRODUCT SPEC. SHEETS PLOT DATE: John A. Calvert January 18, 2023 Date: 2023,01.18 SYSTEM TO BE INSTALLED INFORMATION: UTILITY COMPANY: 14:55:10 -07'00' NUMBER: PROJECT NUEMBER: DC SYSTEM SIZE: 7.9 kW DC Snohomish County Public Utilities District 86917 AC SYSTEM SIZE: 5.8 kW AC (PUD) SHEET NAME: MODULE TYPE: (20) QCells Q.PEAK DUO BILK ML-G10+ 395 COVER SHEET INVERTER TYPE: IQ8PLUS-72-2-US MONITORING: Enphase IQ Combiner 4 X-IQ-AM1-240-4 PERMIT ISSUER: REVISION: PAGE NUMBER: City of Everett 0 PV 1