Laserfiche WebLink
BOEING RENTON FINAL ASSEMBLY ATP SECTION 5 <br />VESDA EARLY WARNINGSNDKEDETECTION SYSTEM TABLE 5-2 <br />UPGRADES SEATRONICS JOB # 111137 SYSTEM ALARM AND CONTROL FUNCTION RESPONSE MATRIX <br />VESDA POSITION 2 <br />X = REQUIRED RESPONSE <br />SYSTEM ALARM & CONTROL RESPONSES TO VERIFY <br />0 = CONFIRM RESPONSE DOES NOT OCCUR <br />RESPONSE AT VESDA CONTRO PANEL (VCP) <br />RESPONSE AT MFAP <br />RESPONSE ON REMOTE MONITORING GRAPHICS <br />STATIONS <br />Abbreviations: <br />X = REQUIRED RESPONSE HO <br />ZO \o9 pQ �O <br />O <br />E = EXISTING CONDITION O <br />TD = RESPONSE OCCURS AFTER TIME DELAY O <br />Z Q � v O'er J ` <br />0 =CONFIRM RESPONSE DOES NOT OCCUR p` p t� �r `Co <br />VQ -p �Q O� �� ���� �� p`/ 44/ <br /><-, <br />TO <br />MFAP - Main Fire Alarm Panel: Refers to main XLS Fire = <br />Q O <br />Alarm Panel Q <br />Q i. O ` O <br />� O p p J= <br />2 J Q QQ O G UO O V V U <v V V O <br />� <br />VDU - Vesda Detector Unit (at referenced airplane position) i.�p �tv0 CD co �� J <br />Z m O Q v i. 2 <br />o v �` �� <v �O �Q �� `Q Q �Q �- �p `Q Q �p ,`Q' <br />o co o <br />VCP - Vesda Control Panel at referenced airplane ) O <br />position) <br />,�V p p <br />4r O J �O Q G O Q C9 tti 2 tr 4r <v <v <br />O 41 44� 4v0 <v O <br />Q �� S� � � Q <c •� � lv ckl O k O Q <br />LINE <br />Q <br />OJO OQ 00� Q JO <br />ITEM <br />TEST CONDITION TO PERFORM �� �� �,��� Qo .� �o �o�� �. �� Q�p` �� �e <br />SMOKE TRANSPORT TIME TEST: APPLY TEST SMOKE <br />1 <br />TO THE FURTHEST AIR SAMPLING HOLE. RECORD TIME <br />BETWEEN INTRODUCTION OF TEST SMOKE AND FIRST <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />— <br />INDICATION ON DISPLAY BARGRAPH. <br />LOW LEVEL SMOKE WARNING TEST: APPLY A SMALL <br />2 <br />AMOUNT TEST SMOKE TO ANY AIR SAMPLING HOLE TO <br />X <br />X <br />X <br />X <br />INDUCE AN "ALERT" LEVEL SMOKE EVENT ON THE <br />VCP. <br />HIGH LEVEL SMOKE ALARM TEST: APPLY A <br />3 <br />SUFFICIENT AMOUNT TEST SMOKE TO ANY AIR <br />X <br />X <br />X <br />X <br />X <br />X <br />X <br />X <br />X <br />X <br />SAMPLING HOLE TO INDUCE A "FIRE" LEVEL SMOKE <br />EVENT ON THE VCP. <br />MANUAL PULL ALARM STATION: ACTIVATE MANUAL <br />4 <br />PULL STATION LOCATED ON THE FRONT OF THE VCP <br />X <br />X <br />X <br />X <br />X <br />X <br />ENCLOSURE. <br />SAVE STATION TEST: INITIATE A HIGH LVL. SMOKE <br />5 <br />ALARM ON THE VESDA CONTROL PANEL. DEPRESS & <br />X <br />X <br />X <br />X <br />0 <br />X <br />X <br />X <br />X <br />X <br />X <br />X <br />HOLD THE SAVE SWITCH. (DO NOT RESET) <br />6 <br />SAVE STATION TEST - CONTINUED: RELEASE SAVE <br />E <br />E <br />E <br />E <br />TD <br />E <br />E <br />E <br />E <br />E <br />E <br />E <br />SWITCH, VERIFY RESPONSES. <br />60" <br />ISOLATE MODE TEST: PLACE THE VCP INTO "ISOLATE" <br />MODE. APPLY A SUFFICIENT AMOUNT OF TEST SMOKE <br />7 <br />INTO ANY AIR SAMPLING HOLE TO RAISE THE SMOKE <br />0 <br />X <br />0 <br />X <br />0 <br />0 <br />0 <br />0 <br />X <br />X <br />0 <br />LEVEL READING ABOVE THE "FIRE" THRESHOLD <br />SETTING OF THE VCP. [RESET VCP BEFORE DE - <br />ISOLATING] <br />"OUT OF SERVICE" MODE CONFIRMATION: PLACE THE <br />8 <br />VCP INTO "OUT OF SERVICE" MODE USING THE PC <br />X <br />X <br />X <br />GRAPHICS STATION. <br />"NORMAL ON" MODE CONFIRMATION: RETURN THE <br />9 <br />VCP TO "NORMAL ON" MODE USING THE PC GRAPHICS <br />X <br />X <br />1 <br />STATION. <br />