431 ALVERSON BLVD 2024-01-03 - Laserfiche WebLink

2018 Washington State Energy Code — Residential Prescriptive Energy Code Compliance for All Climate Zones in Wa i Single Family —New & Additions(effective FebruarY1 20 i i� ((''T2021 V These requirements apply to all !RC building types, including detached o - d t�$-fari�i dwellings and multiple single-family dwellings (townhouses). ITY OF E1�ERETT .. ....... .. . Project Information Contact Informa rm It Se ry i c es & Instructions: This single-family project will use the requirements of the Prescriptive Path below and 4 incorporate the minimum values listed. Based on the size of the structure, the appropriate number f additional credits are checked as chosen by the permit applicant. Provide all information From the following tables as building permit drawings: Table R402.1- Insulatio nd NOV 22 Fenestration Requirements by Component, Table R406.2 - Fuel Normalization Credits and 4C6.3 - En�j'2Djy Credits. 2) I TIE, _ Authorized Representative .�� Date Pei -� v� r �S C, Se�1'ICe '`� ........ ...... ....__ ..._ .... Y All Climate Zones (Table R402.1.1) ..._ _.......... .......................__ ..........._..... ............._ ............. _.._ .................. _ . _..............-....._ .. _ .-............._........................._.............................................................._...............................-.. R-Value a U-Factor a _....... ..._.._ ....... .. _. _. _. ..._ .......... _ ........ __ .................... _......... _.... ......_........._ ............... _ _. Fenestration U-Factor b n/a 0.30 .....................__......................................................................................................................................_...................................._......................................................................................................._...._ . Skylight U-Factor b n/a 0.50 _. _ _ .. _ ..... __ ........ ..._....._. ;._ ..... _._ ................ _.........._ . _ _................. _.-.. __ .................. ...... _ ...__ ........... Glazed Fenestration SHGC b,e n/a n/a ; ......._ ._ ..._ ... _ _ __ ......... _ .............. ....... _........... .... ........... ........ ........... ........ _ ..-... .. ....... ......... .............. . ........ .... ... . Ceiling 2 49 0.026 .................. _..................... __ ...... ................. ............................................. ............._..-........................:........................... ... _............................................ _ . ..... .. . Wood Frame Wall g•" 21 int 0.056 ._.._. .._ ._ _ . _ _....... ..... .......... ...... _._._ ... __. __.. .... __.........__................................ __... __ ... Floor 30 0.029 .... _ .. ....... ......... ......... ......... ........ ......... ......... ....... ............... ..... ................ ........_...: ......... Below Grade Wall `," 10/15/21 int + TB 0.042 Slab d.fR-Value & Depth 10, 2 ft n/a ........ R-values are minimums. U-factors and SHGC are maximums. When insulation is installed in a cavity that is less a than the label or design thickness of the insulation, the compressed R-value of the insulation from Appendix Table A101.4 shall not be less than the R-value specified in the table. b The fenestration U-factor column excludes skylights. _... _ .._ ...... _.. ... ................ "10/15/21 +5TB" means R-10 continuous insulation on the exterior of the wall, or R-15 continuous insulation on the interior of the wall, or R-21 cavity insulation plus a thermal break between the slab and the basement wall at c the interior of the basement wall. "10/15/21 +5TB" shall be permitted to be met with R-13 cavity insulation on the interior of the basement wall plus R-5 continuous insulation on the interior or exterior of the wall. "5TB" means R-5 thermal break between floor slab and basement wall. ......... d R-10 continuous insulation is required under heated slab on grade floors. See Section R402.2.9.1. _.................................... _............._...............11 ...... ........ .. ...I...-. . _ ......._.... ...... ......... .....---. ............. For single rafter- orjoist-vaulted ceilings, the insulation may be reduced to R-38 if the full insulation depth e extends over the top plate of the exterior wall. ............................................................................................................................................................................................................................................................................................................................................................. R-7.5 continuous insulation installed over an existing slab is deemed to be equivalent to the required perimeter f slab insulation when applied to existing slabs complying with Section R503.1.1. If foam plastic is used, it shali meet the requirements for thermal barriers protecting foam plastics. For log structures developed in compliance with Standard ICC 400, log walls shall meet the requirements for g climate zone 5 of ICC 400. _... ..... _.. - _ - __.- _. .............. ..... ........ .... ....................... Int. (intermediate framing) denotes framing and insulation as described in Section A103.2.2 including standard h framing 16 inches on center, 78% of the wall cavity insulated and headers insulated with a minimum of R-10 insulation. Prescriptive Path — Single Family 2018 Washington State Energy Code-R