4815 BAKER DR 2023-10-25 - Laserfiche WebLink

• 2 P0 Washington(� State Energy Code Residential Prescriptive Energy Code Compliance for All Climate Zones in Washington Single Family ''New &Additions (effective February 1,2021) Version 1.0 These requirements apply to all IRC building types, including detached one- and two-family dwellings and multiple single-family dwellings (townhouses). Project Information Contact Information Brickley Rsidence Jonathan Brandt 1122 NE 75th St Seattle,WA 98115 4815 Baker Drive Everett,WA 98203 206-601-8637 jb@jbarch.net Instructions. This single-family project will use the requirements of the Prescriptive Path below and incorporate the minimum values listed. Based on the size of the structure, the appropriate number of additional credits are checked as chosen by the permit applicant. Provide all information from the following tables as building permit drawings. Table R402.1 - Insulation and Fenestration Requirements by Component,Table R406.2 - Fuel Normalization Credits and 406.3-Energy Credits, Authorized R epresentative Jonathan Brandt Digitally signed by Jonathan Brandt Date:2021.07.30 12:36:33-07'00' D 07/30/2021 ate All Climate Zones (Table R402.1.1) R-Value a U-Factor a Fenestration U-Factor b n/a 0.30 Skylight U-Factor b n/a 0.50 Glazed Fenestration SHGC b,e n/a n/a Ceiling e 49 0.026 Wood Frame Wall "'" 21 int 0.056 Floor 30 0.029 Below Grade Wall c.b 10/15/21 int+TB 0.042 Slab "R-Value & Depth 10, 2 ft n/a R-values are minimums. U-factors and SHGC are maximums.When insulation is installed in a cavity that is less a than the label or design thickness of the insulation,the compressed R-value of the insulation from Appendix Table A101.4 shall not be less than the R-value specified in the table. b The fenestration U-factor column excludes skylights. "10/15/21 +STB means R-10 continuous insulation on the exterior of the wall, or R-15 continuous insulation on the interior of the wall, or R-21 cavity insulation plus a thermal break between the slab and the basement wall at c the interior of the basement wall. 10/15/21 +STB shall be permitted to be met with R-13 cavity insulation on the interior of the basement wall plus R-5 continuous insulation on the interior or exterior of the wall. "SIB" means R-5 thermal break between floor slab and basement wall. d R-10 continuous insulation is required under heated slab on grade floors. See Section R402.2.9.1. For single rafter- or joist-vaultedceilings,the insulation may be reduced to R-38 if the full insulation depth e extends over the top plate of the exterior wall. R-7.5 continuous insulation installed over an existing slab is deemed to be equivalent to the required perimeter f slab insulation when applied to existing slabs complying with Section R503.1.1. If foam plastic is used, it shall meet the requirements for thermal barriers protecting foam plastics. For log structures developed in compliance with Standard ICC 400, log walls shall meet the requirements for g climate zone 5 of ICC 400. Int. (intermediate framing) denotes framing and insulation as described in Section A103.2.2 including standard h framing 16 inches on center, 78%of the wall cavity insulated and headers insulated with a minimum of R-10 insulation. ...,, a u ...6r..---:4, 70.E0YE1 DEC 0 3 2021 _ AUG 2 7 2021 CITY OFEVERETT CITY OF EVF P. FACT Permit Services , Prescriptive Path—Single Family Pe20111BiWasinrlgtf evatate Energy Code-R 1