7728 GRANT DR 2023-11-28 - Laserfiche WebLink

GENERAL NOTES AERIAL VIEW CODE AND STANDARDS , "ALL WORK SHALL COMPLY WITH 2017 NATIONAL ELECTRIC CODE(NEC),2015 INTERNATIONAL BUILDING CODE BLUE RAVEN (IBC),2015 INTERNATIONAL RESIDENTIAL CODE(IRC),2015 INTERNATIONAL PLUMBING CODE(IPC),AND ALL STATE AND LOCAL BUILDING,ELECTRICAL,AND PLUMBING CODES. • r , 2.DRAWINGS HAVE BEEN DETAILED ACCORDING TO UL LISTING REQUIREMENTS. - r 1403 N. Research Way SITE NOTES/OSHA REGULATION y ' Orem, UT 84097 1.A LADDER SHALL BE IN PLACE FOR INSPECTION IN COMPLIANCE WITH OSHA REGULATIONS. 800.377.4480 2.THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS A UTILITY INTERACTIVE SYSTEM. WWW.BLUERAVENSOLAR.COM 3.THE SOLAR PV INSTALLATION SHALL NOT OBSTRUCT ANY PLUMBING,MECHANICAL,OR BUILDING ROOF VENTS. 4.ROOF COVERINGS SHALL BE DESIGNED,INSTALLED,AND MAINTAINED IN ACCORDANCE WITH THIS CODE AND =a - ' • . CONFIDENTIAL-THE INFORMATION THE APPROVED MANUFACTURER'S INSTRUCTIONS SUCH THAT THE ROOF COVERING SHALL SERVE TO PROTECT * HEREIN CONTAINED SHALL NOT BE THE BUILDING OR STRUCTURE. USED FOR THE BENEFIT OF ANYONE EXCEPT BLUE RAVEN SOLAR NOR SOLAR CONTRACTOR - '� U` SHALL IT BE DISCLOSED IN WHOLE OR IN PART TO OTHERS OUTSIDE 1.MODULE CERTIFICATIONS WILL INCLUDE UL1703,IEC61646,IEC61730. +d F* i f RECIPIENTS ORGANIZATION,EXCEPT 2.IF APPLICABLE,MODULE GROUNDING LUGS MUST BE INSTALLED AT THE MARKED GROUNDING LUG HOLES PER "'' + "• IN CONNECTION WITH THE SALE AND THE MANUFACTURER'S INSTALLATION REQUIREMENTS. w', � } USE OF THE RESPECTIVE EQUIPMENT, 3.AS INDICATED BY DESIGN,OTHER NRTL LISTED MODULE GROUNDING DEVICES MAY BE USED IN PLACE OF • _ }* r WITHOUT THE WRITTEN PERMISSION STANDARD GROUNDING LUGS AS SHOWN IN MANUFACTURER DOCUMENTATION AND APPROVED BY THE AHJ. I. _ ` s - ... OF BLUE RAVEN SOLAR LLC. 4.CONDUIT AND WIRE SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND ARE NOT MEANT TO ! ■ LIMIT UP-SIZING AS REQUIRED BY FIELD CONDITIONS. ' r 5SUITABLE.CONDUIT COMPOUND. CONDUIT POINT OF PENETRATION FROM EXTERIOR TO INTERIOR TO BE INSTALLED AND SEALED WITH A + NABC E P 6.DC WIRING LIMITED TO MODULE FOOTPRINT W/ENPHASE AC SYSTEM. CERTIFIED] 7.ENPHASE WIRING SYSTEMS SHALL BE LOCATED AND SECURED UNDER THE ARRAY W/SUITABLE WIRING CLIPS. + �_ 8.MAX DC VOLTAGE CALCULATED USING MANUFACTURER PROVIDED TEMP COEFFICIENT FOR VOC UNLESS NOT i i wt PV INSTALLATION 9.ALLINVERTERS,MOTOR GENERATORS,PHOTOVOLTAIC MODULES,PHOTOVOLTAIC PANELS,AC F - PROFESSIONAL PHOTOVOLTAIC MODULES,DC COMBINERS,DC-TO-DC CONVERTERS,SOURCE CIRCUIT COMBINERS,AND - as j Scott Gurney CHARGE CONTROLLERS INTENDED FOR USE IN A PHOTOVOLTAIC POWER SYSTEM WILL BE IDENTIFIED AND . 7r #PV-011719-015866 LISTED FOR THE APPLICATION PER NEC 690.4(B). 10.ALL SIGNAGE TO BE PLACED IN ACCORDANCE WITH LOCAL BUILDING CODE. *' `+pr CONTRACTOR: 11.TERMINALS AND LUGS WILL BE TIGHTENED TO MANUFACTURER TORQUE SPECIFICATIONS(WHEN PROVIDED) r BRS FIELD OPS � IN ACCORDANCE WITH NEC CODE 110.14(D)ON ALL ELECTRICAL CONNECTIONS. * _ # y ' 800-377-4480 EQUIPMENT LOCATIONS �,, ` - r 1.PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT +0 # + WILL BE PROVIDED AS PER SECTION NEC 110.26. • !"ems '&.am 2.EQUIPMENT INSTALLED IN DIRECT SUNLIGHT MUST BE RATED FOR EXPECTED OPERATING TEMPERATURE AS - •�• • - SPECIFIED BYNEC 690.31(A)AND NEC TABLE 310.15(B). Sealed For 3.ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL ACCORDING TO NEC + e Q I !+^ U U APPLICABLE CODES. Existing Roof CX �1y� t� ``1L� Z >a 4.ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED FOR OUTDOOR USAGE WHEN APPROPRIATE. k . Attachment Only Q" ��WAS O M 1 PROJECT INFORMATION: •' 000 C14 NUMBER OF STORIES: 10 p W W CONDUIT RUN: Interior 46056 LL 0) N N ECOBEE QTY: 0 r ■ , ■' .nFSFGISTER�14� Q NCn LIGHT BULB QTY: 0 NAL ENS' - 2 PV METER: Not RequiredDESIGN CRITERIA SITE SPECIFICATIONS SHEET INDEX w w ROOF TYPE (1) INFORMATION: O U (j WIND SPEED: 110 mph CONSTRUCTION -V-B PV1 -COVER SHEET 10/11/2023 j.- Cl) Cl) ROOF TYPE: Comp Shingle GROUND SNOW LOAD: 25 lb ZONING: RESIDENTIAL PV2-SITE PLAN N L N FRAMING TYPE: Manufactured Truss WIND EXPOSURE FACTOR: C PV3- ROOF PLAN :3 r-- > V V SHEATHING TYPE: OSB SEISMIC DESIGN CATEGORY: D PV4-STRUCTURAL V r-- W Q C3 ATTACHMENT: SFM Infinity Flashkit PV5- ELECTRICAL 3-LINE DIAGRAM RACKING: Unirac SFM Infinity @ 48" OC Portrait/72"OC Landscape DRAWING BY: NUMBER OF ATTACHMENTS: 23 SCOPE OF WORK PV6- ELECTRICAL CALCULATIONS PV7-WARNING LABELS AND LOCATIONS Brendan Fillmore ROOF TYPE (2) INFORMATION (IFAPPLICABLE): INSTALLATION OF UTILITY INTERACTIVE PHOTOVOLTAIC SOLAR SYSTEM AND ANY (ALL OTHER SHEETS AS REQUIRED) *SEE PV4.2 NECESSARY ADDITIONAL WORK NEEDED FOR INSTALLATION. SS- PRODUCT SPEC. SHEETS PLOT DATE: October 11, 2023 PROJECT NUMBER: SYSTEM TO BE INSTALLED INFORMATION: UTILITY COMPANY: 873582 DC SYSTEM SIZE: 4.2 kW DC Snohomish County Public Utilities District AC SYSTEM SIZE: 3.15 kW AC (PUD) SHEET NAME: MODULE TYPE: (10) REC Solar REC420AA PURE-R COVER SHEET INVERTER TYPE: Enphase IQ7X-96-2-US MONITORING: Enphase IQ Combiner 4 X-IQ-AM1-240-4 PERMIT ISSUER: REVISION: PAGE NUMBER: City of Everett 0 PV 1