1321 SE EVERETT MALL WAY ANGRY CRAB SHACK 2024-01-08

ABBREVIATED SPECIFICATIONS NOTE: NOT ALL SPECIFICATION SECTIONS MAYBE NEEDED FOR THIS PROJECT. CONTRACTOR TO APPLY SPEC. SECTIONS AS APPLICABLE TO SCOPE OF WORK. GENERAL MECHANICAL NOTE: CONTRACTOR" MEANS "MECHANICAL CONTRACTOR" WHEN REFERENCED ANYWHERE IN THE MECHANICAL CONSTRUCTION DOCUMENTS, UNLESS WORK AND EQUIPMENT HAS BEEN COORDINATED BETWEEN THE MECHANICAL AND GENERAL CONTRACTORS TO BE PROVIDED BY THE GENERAL CONTRACTOR. "NEEDED", "PROVIDE" AND "INSTALL" MEANS ALL ITEMS CALLED OUT IN THE CONTRACT DOCUMENTS AND ANY ADDITIONAL ITEMS NOT CALLED OUT BUT REQUIRED TO MAKE A COMPLETE AND OPERATIONAL SYSTEM. THE INTENT OF THE SPECIFICATIONS AND THE DRAWINGS IS TO VERIFY A COMPLETE AND FULLY OPERATIONAL EXISTING MECHANICAL SYSTEM. THE MECHANICAL CONTRACTOR SHALL FURNISH AND INSTALL ALL LABOR, MATERIAL AND EQUIPMENT NECESSARY TO COMPLETE VERIFY THE FINAL OPERATING CONDITIONS. PERMITS AND FEES: THE MECHANICAL CONTRACTOR SHALL PROCURE AND PAY FOR ALL PERMITS, FEES AND INSPECTIONS NECESSARY TO COMPLETE THE MECHANICAL SCOPE OF WORK. CODES: PERFORM ALL WORK IN ACCORDANCE WITH THE CURRENT MECHANICAL CODE, STATE AND LOCAL CODES / ORDINANCES AND AHJ. ALL WORK SHALL ALSO BE IN COMPLIANCE WITH BUILDING OWNER'S CRITERIA. IN CASE OF CONFLICT BETWEEN THE DRAWINGS, SPECIFICATIONS, CODES, ORDINANCES AND AHJ, THE MOST STRINGENT STANDARD (IN THE OPINION OF THE ENGINEER) SHALL APPLY. THE MECHANICAL CONTRACTOR SHALL SATISFY CODE, AHJ, DRAWINGS AND SPECIFICATIONS, AS A MINIMUM STANDARD, WITHOUT ANY EXTRA COST. THE MECHANICAL CONTRACTOR SHALL COORDINATE REQUIRED MECHANICAL WORK WITH OTHER TRADES AND THE OWNER. STANDARDS: EQUIPMENT AND MATERIALS SHALL CONFORM WITH APPROPRIATE PROVISIONS OF ARL, ASME, ASTM, UL, NEMA, ANSI, SMACNA, ASHRAE, NFPA, OTHER APPLICABLE AGENCIES AND AHJ, AS APPLICABLE TO EACH INDIVIDUAL UNIT OR ASSEMBLY. SITE EXAMINATION: THE MECHANICAL CONTRACTOR SHALL THOROUGHLY EXAMINE ALL AREAS WHERE EQUIPMENT, DUCTWORK AND PIPING WILL BE INSTALLED AND SHALL REPORT ANY CONDITION THAT PREVENTS THE PROPER INSTALLATION OF THE MECHANICAL WORK. AIR HANDLING EQUIPMENT & MATERIALS ALL AIR HANDLING & HVAC SYSTEMS ARE EXISTING ARE INTENDED TO BE RE -USED. THE CONTRACTOR SHALL INSPECT AND SERVICE THE EXISTING SYSTEMS AND COMPONENTS NOTIFYING THE OWNER IF REPAIRS OR REPLACEMENT OF EQUIPMENT OR SYSTEM COMPONENTS ARE NEEDED. OPERATIONAL AIRFLOWS ARE CALLED OUT IN THE PERMIT DOCUMENTS. THE CONTRACTOR SHALL VERIFY THAT THE EXISTING SYSTEM CAN MEET THESE REQUIREMENTS. IF THERE ARE DEFICIENCIES THE CONTRACTOR SHALL NOTIFY THE OWNER AND WORK WITH THE ENGINEER OF RECORD TO INITIATE SYSTEM CHANGES TO RESTORE SYSTEMS TO AIRFLOWS AS NEEDED. DUCTWORK AND ACCESSORIES SHEETMETAL DUCTWORK: ALL DUCTWORK IS EXISTING AND SHALL BE EXAMINED BY THE CONTRACTOR FOR COMPLETENESS AND CONDITION. REQUIRED REPAIRS OR REPLACEMENTS SHALL BE PRESENTED TO THE OWNER. CONTROLS EXISTING CONTROLS SHALL REMAIN AND BE RE -USED. THE CONTRACTOR SHALL TEST AND VERIFY - INFORMING THE OWNER OF DEFICIENCIES AND POTENTIAL REPAIRS AND/OR REPLACEMENT. AWAIT INSTRUCTIONS BEFORE PROCEEDING WITH CHANGES. TESTING, ADJUSTING, AND BALANCING KITCHEN VENTILATION SYSTEMS: VERIFY THE AIRFLOWS (EXHAUST AND MAKEUP AIR) MATCH CFMS DEFINED IN THESE PLANS. IF THEY DO NOT, NOTIFY THE OWNER AND FOR FOR FURTHER INSTRUCTIONS. RESTAURANT SEATING AREA HVAC SYSTEMS: NO WORK IN THIS AREA SYSTEM COMMISSIONING NOT REQUIRED. GENERAL NOTES 1. ALL MECHANICAL SYSTEM ARE EXISTING AND BEING REUSED. MECHANICAL SHEET INDEX Sheet List Table Sheet Number Sheet Title M0.01 MECHANICAL SPECIFICATIONS M2.01 MECHANICAL HVAC PLAN M5.01 MECHANICAL DETAILS MECHANICAL ABBREVIATIONS MECHANICAL LEGEND NOTE: NOT ALL SYMBOLS MAY BE USED IN THESE DRAWINGS. MAX MAXIMUM MECH MECHANICAL MC MEP MECHAN CAL CONTRACTOR MECHANICAL, ELECTRICAL TYP. SUPPLY DUCT UP/DN MFG AND PLUMBING MANUFACTURER ON UP NJ DUCT HEATER AFF ABOVE FINISHED FLOOR MIN MINIMUM F"T L TYP. RETURN DUCT UP/DN MANUAL VOLUME DAMPER AHJ AUTHORITIES HAVING JURISDICTION NTS NOT TO SCALE ON UP o BACK DRAFT DAMPER m APPROX APPROXIMATE OSA OUTSIDE AIR El: [a TYP. EXHAUST DUCT UP/DN BAROMETRIC DAMPER BLDG BUILDING umi DUCT SMOKE DETECTOR PM PROJECT MANAGER TURNING VANES CLG CEILING MOTORIZED DAMPER CONST CONSTRUCTION REF REFERENCE CD CEILING DIFFUSER REQ('D) REQUIRE(D) O THERMOSTAT COMBINATION SMOKE AND FIRE REV REVISED/REVISION DAMPER DEG DEGREES RG RETURN GRILLE DTL DETAIL O SENSOR SPIN -IN TAKE -OFF AND VOLUME ON DOWN SHT SHEET DAMPER DWG(S) DRAWING(S) SPECS SPECIFICATION(S) y SUPPLY AIR ARROW SF SQUARE FEET o-> UNDERCUT DOOR EA EACH SS STAINLESS STEEL EC ELECTRICAL CONTRACTOR RETURNAIRARROW ELEC ELECTR CAL TEMP TEMPORARY EM EMERGENCY TYP TYPICAL OR (EX)EXISTING EX EXT EXTERIOR UNO UNLESS NOTED OTHERWISE EG EXHAUST GRILLE WH WATER HEATER 12 X 8 INDICATES UNLINED 12" z 8" O.D. SHEETMETAL F&I FURNISH & INSTALL (1ST FIGURE SIDE SHOWN FLR FLOOR 2ND FIGURE SIDE NOT SHOWN) FOOI � GIC GENERAL CONTRACTOR HR HOUR �l�llll IIIIIIII FLEXIBLE DUCT HVAC HEATING VENTILATING &AIR CONDITIONING NECK SIZE ILL LANDLORD LV LOW VOLTAGE XX—X DIFFUSER TYPE, REF. SCHEDULE XXXX DESIGN CFM (WHERE APPLICABLE) CFM SHOWN FOR RETURN ARE UNOCCUPIED MODE CEILING DIFFUSER (FLOW ARROWS SHOWN O INDICATE DIRECTION OF AIR FLOWS) E� CEILING RETURN / EXHAUST GRILLE 1 M0.0 DETAIL MARK DETAIL MARK MX X SHEET WHERE DETAIL IS SHOWN XXXXX EQUIPMENT MARK - SEE SCHEDULE PROJECT SCOPE OF WORK AN EXISTING BUILDING SHALL BE REMODELED FOR NEW TENANT. TWO EXISTING TYPE 1 HOODS SHALL REMAIN, ONE SHALL BE RE -USED, THE OTHER ABANDONED IN PLACE. EXISTING HVAC UNITS AND DUCTWORK TO REMAIN AS -IS. THE ONLY MECHANICAL SCOPE IS START UP AND BALANCE VERIFICATION OF THE EXISTING TYPE I HOOD SYSTEM (SEE PLANS): ALSO DUCT CLEANING AND OPERATIONAL CHECK OF SYSTEM IS NEEDED PER THESE PLANS. VICINITY MAP B9th St SE BothA Everett T 91 st e se � n 93,d at SE m 9nth at m BtR HI BE B"tetq1at, vyal OQ4ER C. v 5504 hw4 t Cc s`SJONALO Y U a U) R. Q _ W W ao '§ o U � 0 Z > 3 LU z 0 k w 0w Z�N� �w IL Q a w REVISIONS 52 a b SHEETTITLE MECHANICAL SPECIFICATIONS rermit bet C.O. CHECKED BY, chm SHEET M0.01