Laserfiche WebLink
Exterior Lighting amp : e LTG-EXT <br /> 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2,R3,R4 over 3 stories and all R1 Revised Nov 2017 <br /> Project Title: DSE-1 -Everett WA , Date 4/30/2020 <br /> Exterior Lighting 0 Zone 1 0 Zone 2 • Zone 3 0 Zone 4 For Building Department Use <br /> Zone Exterior Lighting Zone selection required to enable LTG-EXT form. <br /> Zones are defined in Table C405.5.2(1)and specified by the <br /> juiioJit tiun. <br /> Calculation Area <br /> 0 New construction 0 Addition-stand 0 Addition <br /> +existing <br /> Q Alteration with<50% Q Alteration with z 50%ext. <br /> ext.wattage replaced wattage replaced User Note <br /> Building Grounds 0 Efficacy>80 lumens/watt D Exemptio <br /> Applies to individual <br /> luminaires>100 Watts 0 Controlled by motion sensor <br /> Tradable Maximum Allowed Lighting Wattage NOTE? Base Site Allowance: 750 <br /> Area(ft2),perimeter Allowed Watts Allowed Watts <br /> Tradable Surfaces Surface Description (If)or#of items per ft2 or per If x ft2(or x it.)NOTE 2 <br /> Uncovered Parking and drives Parking 63400 0.08 W/ft2 5072 <br /> Total Allowed Tradable+Site Allowance Watts: 5822 <br /> Tradable Proposed Lighting Wattage NOTE3 <br /> Number of Watts per Watts <br /> Tradable Surface Fixture Description NOTE 4,5 Fixtures Fixture NOTE 6 Proposed <br /> Uncovered Parking and drives W1 7 13 91 <br /> Uncovered Parking and drives W2 14 71 994 <br /> Uncovered Parking and drives P1 6 125 750 <br /> Total proposed tradable'netts may not exceed the sum of total allowed tradable Total Proposed Tradable Watts: 1835 <br /> watts plus the base site allo'nence. Any base site alloNence not needed to make <br /> tradable Ketts comply can be applied to individual non-tradable categories. <br /> Non-Tradable Maximum Allowed Lighting Wattage NOT" Site Allowance Remaining: 750 <br /> Area(ft12),perimeter Allowed Watts Allowed Watts <br /> Non-Tradable Surfaces Surface Description (It)or#of items per ft2,If or item x ft2(or x If)NOTE 2 <br /> • <br /> Non-Tradable Proposed Lighting Wattage NOTE3,7 <br /> Number of Watts per Watts <br /> Non-Tradable Surface Fixture Description NOTE 4,5 Fixtures Fixture NOTE 6 Proposed <br /> Non-tradable proposed watts may not exceed allowed Netts for any individual Non-Tradable Watts Exceeding LPA: 0 <br /> surface unless the total excess Netts for all non-tradable surfaces are less than <br /> the remaining site allovence. Remaining Site Allowance: 750 <br /> Exterior Lighting COMPLIES WITH MAX. ALLOWANCE <br /> Note 1-List all exterior surfaces per Table C405.5.2(2)that occur in the project scope.Select exterior surface categories from drop doing? menu <br /> Note 2-Unlit Message-Enter lighting fixture information for this surface in Proposed Lighting Wattage table to generate Lighting PoKer Allove <br /> Note 3-List all proposed lighting fixtures including existing-to-remain fixtures. <br /> Note 4-For proposed Fixture Description,indicate fixture type,lamp type,number of lamps in the fixture, and ballast type(if applicable). <br /> Note 5-Existing-to-remain fixtures shall be included in the Tradable and Non-Tradable Proposed Lighting Wattage tables in the same manner <br /> as new fixtures. Identify as existing in fixture description. <br /> Note 6-For proposed Watts/Fixture enter the luminaire Nettage for installed lamp and ballast using manufacturer or other approved source.Foi <br /> luminaires Kith screw-in lamps,enter the manufacturer's listed maximum input vettage of the fixture(not the lamp vettage). For low <br /> voltage lighting,enter the vettage of the transformer. <br />