1410 SEINER DR 2024-04-12 - Laserfiche WebLink

• ® NOTIFIER �/�. by Honeywell NP-200 Series Photoelectric Smoke Detectors for FireWarden Series The NOTIFIER®NP-200 Series intelligent plug-in smoke detectors are designed for both performance and aesthetics, and are direct replacements for the NP-100 Series.A new modern,sleek,contem- porary design and enhanced optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources in accordance with more stringent code standards. Exclusively for use with NOTIFIER's FireWarden Series address- able fire alarm control panels,the NP-200 Series point ID capability allows each detector's address to be set with rotary, decimal address switches, providing exact detector location for emergency personnel to quickly locate a fire during its early stages, potentially saving precious rescue time while also reducing property damage. Two LEDs on each sensor light to provide a local,visible sensor indi- cation. w The NP-200 Series also offers 135°F(57°C)fixed temperature ther- mal sensing on the NP-200T and a remote test capable detector on the NP-200R for use with DNR(A)/DNRW duct smoke detector housings. Features • Separate base allows interchange of photoelectric,ionization and SLC LOOP: thermal sensors • Two-wire SLC loop connection OPTIONS: • Unit uses base for wiring • Optional relay,isolator,and sounder bases • Compatible with FlashScan®and CLIP protocol systems Installation • Stable communication technique with noise immunity NP-200 Series plug-in intelligent smoke detectors use a detachable ADDRESSING: base to simplify installation, service and maintenance. Installation • Addressable by device instructions are shipped with each detector. • Rotary,decimal addressing Mount detector base(all base types)on an electrical backbox which (Refer to the FireWarden panel manuals for device capacity.) is at least 1.5" (3.81 cm) deep. For a chart of compatible junction ARCHITECTURE: boxes,see DN-60054. • Sleek,low profile,stylish design NOTE:Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring "T-taps"or branches are • Unique single-source design to respond quickly and dependably permitted for Style 4(Class"B")wiring only. to a broad range of fires When using relay or sounder bases, consult the N100-ISO installation • Integral communications and built-in device-type identification sheet 156-3625 for device limitations between isolator modules and iso- lator bases. • Built-in tamper resistant feature • Remote test feature from the panel Construction • Walk test with address display(an address on 121 will blink the These detectors are constructed of fire-resistant plastic.The NP-200 detector LED:12-[pause]-1(FlashScan systems only) Series plug-in intelligent smoke detectors are designed to commer- • Built-in functional test switch activated by external magnet cial standards and offer an attractive appearance. • Removable cover and insect-resistant screen for simple field cleaning Operation • Expanded color options Each NP-200 Series detector uses one of the panel's addresses (total limit is panel dependent)on the FireWarden Signaling Line Cir- OPERATION: cult (SLC). It responds to regular polls from the control panel and • Designed to meet UL 268 7th Edition reports its type and the status.If it receives a test command from the • Factory preset at 1.5%nominal sensitivity for panel alarm thresh- panel (or a local magnet test), it stimulates its electronics and old level reports an alarm. It blinks its LEDs when polled and turns the LEDs fea- • LED"blinks"when the unit is polled (communicating with the fire on when commanded by the panel.The NP-200 Series offers pED l) nk when i alarm. tures and performance that represent the latest in smoke detector technology. • Low standby current MECHANICALS: Detector Sensitivity Test • Sealed against back pressure Each detector can have its sensitivity tested(required per NFPA 72, • SEMS screws for wiring of the separate base Chapter 14 on Inspection, Testing and Maintenance)when installed/ connected to an FireWarden Series addressable fire alarm control • Designed for direct-surface or electrical-box mounting panel. The results of the sensitivity test can be printed for record • Plugs into separate base for ease of installation and maintenance keeping. DN-60979:B•7/1/2019—Page 1 of 3