Laserfiche WebLink
• <br /> 40 <br /> • <br /> Octobe(2011 Section 2 System Components Page 2-2 <br /> • Amerex Restaurant Fire Suppression System EX 4658) <br /> • <br /> • 375 CYLINDER MOUNTING BRACKET(P/N 16085) <br /> • The mounting bracket is used to secure the KP/ZD 375 - ' <br /> Agent Cylinder Assembly to the mounting surface and to ;` ' <br /> 41 connect the discharge valve to the distribution-piping ' '- <br /> • network. The bracket consists of a formed steel assembly ++ <br /> with vertical and horizontal supports and an integral pipe I! j j (l <br /> Ld <br /> • thread adapter with 1/" NPT threads. The pipe thread e !i i j' <br /> adapter maybe oriented to anyconvenient outletposition. i ' i !I! <br /> • p O 1 l <br />' • DISTRIBUTION HOSE (PIN 13069) <br /> i1� Q <br /> `II <br /> • The distribution hose is used to connect the agent cylinder 1, <br /> assembly to the distributor block (P/N 13105). The supply 1 <br /> • line is connected to the distributor block (included with 1:r <br /> • cylinder mounting bracket). <br /> i <br /> • 375 AGENT CYLINDER BRACKET (P/N 17690) 6 / a, <br /> L <br /> • The mounting bracket is used to secure the KP/ZD 375 Agent Cylinder 5-7 ' <br /> Assembly to the mounting surface. The bracket assembly comes with a <br /> • S.S. belly strap and a swivel adapter for connection of the valve outlet to ' ; i <br /> the piping network. The bracket is made from formed carbon steel metal F i I <br /> and dry painted red. ""' ` , I. ' <br /> •• MODELS 275/375& 475 CYLINDER ` <br /> I <br /> { <br /> MOUNTING BRACKET(P/N 1 + <br /> The 275/375&475 Mounting Bracket is used to secure the Models 275/375 & ' i I i I <br /> 475 Agent Cylinder Assembly to the mounting surface. The Cylinder Mounting 11 , 1 I 1' <br /> Bracket is made from 1/8"thick formed steel and painted red to resist corrosion. I <br /> The assembly comes with a stainless steel belly strap and a Swivel Adapter for ' ' <br /> 40 connection to the cylinder valve outlet. Iw, f!I ..l <br /> • SWIVEL ADAPTER(P/N16901) `\ <br /> • The Swivel Adapter connects the distribution piping- '1- ` ,+ <br /> "A" NPT to the valve outlet. , , , ; �� �• <br /> • <br /> • AGENT CYLINDER ASSEMBLY <br /> MODEL 600(P/N 15196) CE MARK/EN3 MODEL 600 (P/N 16339) rallillik <br /> • Amerex MODEL 600 - 6.14 Gallon Capacity - Agent Cylinder <br /> • Assembly is shipped factory filled with Amerex Kitchen Wet Chemical ■ <br /> Agent. It is pressurized with dry Nitrogen or argon gas to a pressure of <br /> II 240 psi (1655 kPa) at 70°F (20°C). The nitrogen charge is the expellant <br /> • gas which discharges the KP agent through the distribution network. imimmimmimmil; <br /> Cylinders are shipped from the factory with a shipping plate installed on t <br /> • the top of the valve to prevent accidental discharge and an anti-recoil <br /> • plate on the valve outlet to redirect chemical flow should an accidental <br /> discharge occur. BOTH OF THESE PLATES MUST BE REMOVED P/N 15196 U.S. METRIC <br /> • AT INSTALLATION. <br /> • Height 27.59 in 70.08 cm <br /> KP600 Agent cylinders are DOT 4BW240, tested to 480 psi (3309 <br /> • kPa) and require a hydrostatic test every twelve (12) years. The Diameter 12 in 30.5 cm <br /> • operating temperature of this and other listed components is 32°F to <br /> 120°F (0°C to 49°C). The machined, forged brass discharge valve is Weight full 114 lb 51.70 kg <br /> • actuated via a pneumatic actuator. The Mechanical Release Module <br /> supplies the N2 required for actuation of one (1) to six (6) KP600 Capacity 6.14 gal 23.2 liter <br /> Agent Cylinder Assemblies. <br /> • <br />