Laserfiche WebLink
This calculator provided voltage drop calculations in three formats (Point to Point, End of Line, and Load Centering). <br />Make sure that you know what method is accepted by, and the results do not exceed the limits set by the res ective jurisdiction <br />Point to Point Method <br />End of Line Method <br />Load Centering Method <br />Project Name <br />ZAP ENERGY <br />CIRCUIT IS WITHIN LIMITS <br />CIRCUIT IS WITHIN LIMITS <br />CIRCUIT IS WITHIN LIMITS <br />Date <br />2/17/23 <br />Circuit Number <br />RELEASE 1 <br />Totals <br />Voltage <br />Drop <br />Totals <br />Voltage <br />Totals <br />Voltage <br />Area Covered <br />CLEAN AGENT SOLENOID <br />Current <br />Distance <br />Current <br />Distance <br />Drop <br />Current <br />Distance <br />Drop <br />Nominal System Voltage <br />Minimum Device Voltage <br />24 <br />1.150 <br />70 <br />0.61 <br />1.150 <br />70 <br />0.787 <br />1.150 <br />70 <br />0.394 <br />16 <br />End of Line Voltage <br />23.39 <br />End of Line Volta e <br />23.21 <br />End of Line Voltage <br />23.61 <br />Total Circuit Current <br />1.150 <br />Wire <br />Ohm's <br />Percent Drop <br />2.55% <br />Percent Drop <br />3.28% <br />Percent Drop <br />1.64% <br />Gauge <br />Per 1000 <br />End of Line and Load Centering Methods use only the wire guage for the first device to source <br />Distance from source to 1st device <br />50 <br />16 <br />4.89 <br />Standard Wire Resistance in Ohms per 1000 feet. <br />Wire Gauge for balance of circuit <br />16 <br />4.89 <br />18=7.77 16=4.89 14=3.07 12=1.98 10=1.24 <br />Enter current in amps. <br />Distance <br />18-14 Aw = Solid Conductors 12-10 Awg = Stranded Conductors <br />.150 = 150 ma <br />from <br />Voltage <br />Notes: <br />Device <br />Device <br />previous <br />At <br />Drop from <br />Percent <br />Wire resistance is doubled in the calculations for two wires (Positive and Negative) <br />Number <br />Current <br />device <br />Device <br />source <br />Drop <br />The voltage calculated to the last device in any method must not be lower then <br />Device 1 <br />0.750 <br />50 <br />23.44 <br />0.562 <br />2.34% <br />the manufactures listed minimum operating voltage (IE: rated operating voltage 20-32 VDC). <br />Device 2 <br />0.100 <br />5 <br />23.42 <br />0.582 <br />2.42% <br />Device 3 <br />0.100 <br />5 <br />23.40 <br />0.597 <br />2.49% <br />Device Manufacturer <br />Kidde <br />Device Manufacturer <br />Other <br />Device 4 <br />0.100 <br />5 <br />23.39 <br />0.606 <br />2.53% <br />Current <br />@Rated <br />Voltage <br />Current <br />@Rated <br />Voltage <br />Device 5 <br />0.100 <br />5 <br />23.39 <br />0.611 <br />2.55% <br />Solenoid <br />Solenoid <br />END <br />23.39 <br />0.611 <br />2.55% <br />Model # <br />Candela <br />Model # <br />Candela <br />END <br />23.39 <br />0.611 <br />2.55% <br />890281 Momentary <br />3" <br />2.000 <br />Sprinkler <br />0.750 <br />END <br />23.39 <br />0.611 <br />2.55% <br />486500 Continuous <br />1.5" & 2" <br />0.2 <br />END <br />23.39 <br />0.611 <br />2.55% <br />895630 Momentary <br />2 <br />END <br />23.39 <br />0.611 <br />2.55% <br />897494 Continuous <br />1.65 <br />END <br />23.39 <br />0.611 <br />2.55% <br />END <br />23.39 <br />0.611 <br />2.55% <br />NATURA PRIMATY <br />0.750 <br />END <br />23.39 <br />0.611 <br />2.55% <br />NATURA SECONDARY <br />0.100 <br />END <br />23.39 <br />0.611 <br />2.55% <br />END <br />23.39 <br />0.611 <br />2.55% <br />END <br />23.39 <br />0.611 <br />2.55% <br />END <br />23.39 <br />0.611 <br />2.55% <br />END <br />23.39 <br />0.611 <br />2.55% <br />END <br />23.39 <br />0.611 <br />2.559. <br />END <br />23.39 <br />0.611 <br />2.55% <br />Totals <br />1.150 70 End of Line Voltage <br />23.39 <br />