Laserfiche WebLink
PVC & CPVC SCHEDULE 80 FITTINGS, UNIONS, <br /> TANK ADAPTERS, EXPANSION JOINTS & SADDLES <br /> The information contained in this publication is based on current information and Product design at the time of publication and is subject to <br /> change without notification.Our ongoing commitment to product improvement may result in some variation.No representations,guarantees <br /> or warranties of any kind are made as to its accuracy,suitability for particular applications or results to be obtained therefrom.For verification <br /> of technical data or additional information not contained herein,please contact Spears°Technical Services Department[West Coast: <br /> (818)364-1611 —East Coast:(678)985-12631 <br /> General Information <br /> Recommendations For Installers And Users <br /> Plastic piping systems should be ENGINEERED, INSTALLED and OPERATED in accordance with ESTABLISHED DESIGN AND ENGINEERING <br /> STANDARDS AND PROCEDURES for plastic piping systems.Suitability for the intended service application should be determined by the installer and/ <br /> or user prior to installation of a plastic piping system. PRIOR TO ASSEMBLY,all piping system components should be inspected for damage or <br /> irregularities.Mating components should be checked to assure that tolerances and engagements are compatible.Do not use any components <br /> that appear irregular or do not fit properly.Contact the appropriate manufacturer of the component product in question to determine usability. <br /> Consult all applicable codes and regulations for compliance prior to installation. <br /> Solvent Weld Connections—Use quality solvent cements and primers formulated for the intended service application,pipe size and type of joint.While <br /> the pipe and fitting materials may be compatible with the intended medium,the solvent cement may not be.Consult the manufacturers for suitability of <br /> use.Read and follow the cement and primer manufacturers'applications and cure time instructions thoroughly.Be sure to use the correct size applicator. <br /> Threaded Connections—Use a quality grade thread sealant.WARNING:SOME PIPE JOINT COMPOUNDS OR PTFE PASTES MAY CONTAIN <br /> SUBSTANCES THAT COULD CAUSE STRESS CRACKING TO PLASTIC.Spears°Manufacturing company recommends the use of Spears° <br /> Thread Sealant which has been tested for compatibility with Spears°products.Please follow the sealant manufacturers'application/installation instructions. <br /> Choice of an appropriate thread sealant other than those listed above is at the discretion of the installer.1 to 2 tums beyond FINGER TIGHT is generally <br /> all that is required to make a sound plastic threaded connection.Unnecessary OVERTIGHTENING will cause DAMAGE TO BOTH PIPE AND FITTING. <br /> Standards and Specifications <br /> Molded Schedule 80 PVC products are manufactured to ASTM D 2467 for use with pipe manufactured to ASTM D 1785. Molded Schedule 80 <br /> CPVC products are manufactured to ASTM F 439 for use with pipe manufactured to ASTM F 441. Certain products carry reduced pressure <br /> handling capability and have maximum internal pressure ratings at 73°F noted. <br /> Fabricated Schedule 80 PVC pressure fittings(part numbers ending with "F") are manufactured to Spears°specifications for use with pipe <br /> manufactured to ASTM D 1785.Schedule 80 CPVC fabricated fittings for use with pipe manufactured to ASTM F 441.See publication FAB-7, <br /> General Specifications for Standard Fabricated Fittings for additional information. <br /> All specified Schedule 80 PVC and CPVC products are manufactured from materials certified by NSF®for use in potable water service. <br /> "Lead Free"low lead certification—unless otherwise specified,all Spears°Schedule 80 fittings specified here-in are certified by NSF International <br /> to ANSI/NSF®Standard 61,Annex G and is in compliance with California's Health&Safety Code Section 116825(commonly known as AB1953) <br /> and Vermont Act 193.Weighted average lead content<=0.25%.Spears°PVC and CPVC Pipe,Fittings and Valves have always been lead-free <br /> and Certified by NSF International for use in potable water systems. Spears°offers a wide range of lead-free specialty fittings and transition <br /> adapters for plumbing applications. However,certain brass threaded adapter fittings for applications that are not intended to convey water for <br /> human consumption through drinking or cooking are still produced and available. <br /> NOT FOR DISTRIBUTION OF COMPRESSED AIR OR GAS <br /> 927 Progressive Products from Spears'Innovation and Technology SPEARS°MANUFACTURING COMPANY <br />