Laserfiche WebLink
• <br /> DURO-TUFF®60-MIL MEMBRANE <br /> Physical Properties: <br /> DT60 has been subjected to the tests required by ASTM D4434"Standard Specification for Poly(Vinyl Chloride) <br /> Sheet Roofing"and has been classified as a Type Ill, internally reinforced sheet.The results of each test are <br /> listed below.ASTM's Overall Thickness requirements for the membrane are plus or minus 10%(nominal)of the <br /> listed Typical Value. <br /> Physical Property Test Method ASTM D4434 Requirement Result Typical Value <br /> Overall Thickness ASTM D751 ?0.054 and 5 0.066 in. PASS 0.060 in.(60 mil),nominal <br /> (>_54 and 5 66 mil) <br /> Thickness Over Scrim ASTM D7635 >_0.016 in. PASS 0.031 in.(31 mil) <br /> Breaking Strength' ASTM D751 Grab Method >_200 lbf./in. PASS 437 x 304 lbf./in. <br /> Elongation' ASTM D751 Grab Method Z 15% PASS 29%x 30% <br /> Seam Strength ASTM D751 Grab Method >_327 lbf. PASS 463 lbf. <br /> (75%of Breaking Strength.) <br /> Tear Strength' ASTM D751 Procedure B >_45 lbf. PASS 78 x 190 Ibf. <br /> Low Temp.Bend ASTM D2136 Must pass at-40°F. PASS PASS <br /> Heat Aging ASTM D3045 Conditioned for 56 days in oven PASS PASS <br /> maintained at 176°F. <br /> 10,000 hours total test time. <br /> Irradiance level of 0.35 W/m2-340nm. <br /> Accelerated Weathering ASTM G155 Cycle:102 minutes light,18 minutes PASS PASS <br /> light+H2O spray,63t2.5°C black <br /> panel,30t5%RH <br /> Conditioned for 6 hours in oven <br /> Dimensional Stability' ASTM D1204 maintained at 176°F. PASS 0.30%x 0.10% <br /> Allowable change:5 0.5% <br /> Immersed in water at 158°F <br /> Water Absorption ASTM D570 for 168 hours. PASS 2.29% <br /> Allowable weight change:5 3% <br /> Static Puncture ASTM D5602 >_33 lbf. PASS z 33 lbf. <br /> Dynamic Puncture ASTM D5635 z 14.7 ft-Ibf.(20 J) PASS i >_14.7 ft-Ibf.(20 J) <br /> 'Typical values are shown for both machine and cross machine directions.The machine direction results are listed first. <br /> Additional Tests <br /> Fungi Resistance ASTM G21 No Sustained Growth or Discoloration <br /> Moisture Vapor Transmission ASTM E96,Proc.B,Method A <0.35 U.S.perms <br /> 0.1.SSIP <br /> . C 'SPRI <br /> us <br /> ® APPROVED 4i) CRC Saw OM Nov.team., <br /> APPROVEMt P MTNG°OITCT.• <br /> R10128 /MAW <br /> I5I21 <br /> www.duro-last com .. of-Z 800-248-0280 <br /> Duro-Last,Cleat Plate,'World's Best Roof,Duro-Bond,and Duro-Tuff are registered trademarks owned by Duro-Last,Inc. <br /> LEED is a registered trademark owned by the U.S.Green Building Council. <br /> Revised:11/21/2013,04/25/2015,05/13/2014,06/10/2014,01/23/2015,05/18/2015,02/15/2016,06/29/2016,05/02/2018,04/03/2019,09/23/2021,08/04/2022 <br />