3003 W CASINO RD BLDG 40-30 2024-04-02

M r MN r WM — — En — all NM N 1 - - E MI T 11111 PRODUCT INFORMATION INSTALLATION INSTRUCTIONS GENERAL GUIDELINES FOR ARIES SUPPLIED PARTS 7. Insert the card into the desired slot and push NETLINKTM EXPANSION CARDS • DACT Card, P/N 76-800015-001 gently to ensure a good connection with the • Cards can be plugged into any slot in the Expansion • Two (2)#8 mounting screws (provided in kit) backplane connector. Card Cage. There are no reserved slots. 8. Locate two #8 mounting screws in the hard- • Power must be off when removing or connecting ware kit. Insert the two mounting screws into PCBs and cabling. Removal of any card does not REQUIRED TOOLS the top and bottom mounting holes and require removal of any other card or its wiring. • Wrist ground strap tighten securely. • Each Expansion Card is automatically assigned a • Phillips screwdriver 9. Make wiring connections. (Refer to Figure 3.) unique address. 10. Remove wrist ground strap from enclosure. • An Expansion Card Cage contains a total of six (6) Expansion Card slots. PROCEDURE WIRING For complete Expansion Card information, see the For communication to a central monitoring station, ARIES NETLink Installation, A, and Maintenance Operation, Use a ground strap to prevent static P discharge that could damage sensitive connect one or two phone lines to the phone jack Manual, P/N 06-237058-001. CAUTION components on the PCBs. connectors located on the the DACT Card (labeled Phonel and Phone2). Each accepts a different sources of power can be RJ45X phone jack. The connections are Loop connected to the control unit. Disconnect Start Public Switched Telephone Network connec- both sources of power and critical compo- nents such as control heads for special pilot relays controlling facility-power tions which meet the specifications of UL864, FCC _� © extinguishing systems and addressable Part 68. ar I1'wo WARNING shutoff before beginning this procedure. >� The control unit and associated equip- ment may be damaged by connecting wir- ing while the control unit is energized. Part Number Part Name To install a DACT card into a Card Cage slot: 76-800015-001 Digital Alarm Communicator Transmitter (DACT)Card Figure 1. Inserting DACT Card into Figure 2.DACT Expansion Card 1. Make sure the enclosure location is dry and that Card Cage Slot the enclosure is free of construction dust and DESCRIPTION metal shavings prior to installing the card. SPECIFICATIONS The Digital Alarm Communicator Transmitter (DACT) 2. The ARIES NETLink system must be powered - Card is an optional system component which transmits down properly before installing card. Dimensions: • 3.5 in. (H)x 7.0 in. (W) (89 mm x 178 mm) system status over phone lines to a Central Station. 3. Slip on a wrist ground strap and clip the ground The DACT Card includes a built-in modem and two strap to the earth ground in the enclosure. Do not Operating Voltage/ Nominal 24 Vdc @ 37mA Loop Start Public Switched Telephone Network(PSTN) remove any card from its shipping carton unless Current: connections (for use with RJ45X phone jacks). Green/ you have established a common earth-ground Electrical • PSTN line using a RJ45X yellow status LEDs are visible from the outside edge of potential among yourself, the enclosure, and the Interface: phone jack the module, where green indicates data transmission shipping carton. • SIA DC-05-1999.09 Ademco and yellow indicates data reception. Red status LEDs Contact ID 4. Unlock and open the control unit door. Protocols: are provided for each channel. 5. Remove the card to be inserted from its packag- • SIA DC 03 1990.01 The DACT Card occupies a single slot in the Card ing. (R2003.10) Cage and plugs directly into the backplane. +24 Vdc 6. Orient the card as shown in Figure 1. Digital Alarm Compatible with Sur-Gard System I, power is supplied via the backplane connector. A g Communicator Sur-Gard System Ill and Osborne ARIES NETLink system can include only one DACT Receivers (DACRs): Hoffman Model 2000E Card per control unit.