2404 74TH ST SE 2024-06-13 - Laserfiche WebLink

i Permit Inspections V E R E T T City of Everett WASHINGTON Permit Number: P2303-006 Description: REPLACE EXISTING PLUMBING WITH NEW Applied:3/8/2023 Approved:3/8/2023 Site Address: 2404 74TH ST SE Issued:3/8/2023 Finaled: 3/19/2024 City,State Zip Code: EVERETT,WA 98203 Status: FINALED Applicant:WILLIAM VELASCO Parent Permit: B2202-028 Owner:VELASCO WILLIAM&IMELDA DOMINICA A Parent Project: Contractor: OWNER Details: SCHEDULED DATE COMPLETED DATE TYPE INSPECTOR RESULT REMARKS 5/1/2023 5/1/2023 PLUMB 03i-ROUGH JEFF M RHODE NOT READY see notes Notes: 425-737-8639 itbuddilld@yahoo.com -plumbing system not ready for inspection 5/22/2023 5/22/2023 PLUMB 03-ROUGH JASON CORRECTION see notes IN MORRISSEY REQUIRED Notes: 425-737-8639 IPBUDDILLE@YAHOO.COM -San Tee fittings cannot be used on their back.All three toilets have San tees on their back being used as a closet bend and drain tie in for other fixtures. Per the UPC 310.3 Waste Connection,and 706.4 Vertical to horizontal.-Trap arm connection from lays and auto washers to vertical vents needs to be made with a San Tee fitting per the UPC 905.5 Location of Opening.-Upstairs bathroom fixtures cannot drain through 3"vent for basement lav per the UPC 908.1 Vertical Wet Venting.Has to be within same floor level and fixtures that are 2 DFUs or less with a maximum of 4DFUs.-Install approved 18 gauge nail plates over piping within 1"of stud face.Plates must extend 11/2"beyond the pipe in both directions per UPC 312.9 Steel Plates.-Install approved 4"end of line clean-out in basement and 2"clean-out on kitchen drain per the UPC 707.4 Location.-Cross sectional vent area through the roof must equal 12.56"per the UPC 904.1 Aggregate Cross Sectional Area.-Fasten closet flanges to floor surface with approved corrosion resistant screws.-Multiple leaks on DWV system.*** List is not exhaustive. 6/26/2023T6/26/2023 PLUMB 03-ROUGH JASON CORRECTION see notes IN MORRISSEY REQUIRED Notes: 425-737-8639 IPBUDDILLE@YAHOO.COM -Install cleanout on kitchen sink drain per the UPC chap 7-Add 2"vent for downstairs toilet rolled above centerline per UPC chap 9.-Use proper combination fittings on vents below flood rim and drains per chap 7 and 9.*** Both upstairs toilets require combination fittings for dry vent and wet vent.-Install missing nail plates on upstairs half bath toilet vent on top and bottom plates both sides of wall.-Install 4"clean-out tee for building drain clean-out to be used as clean-out for both directions per the UPC chap 7.-Wrap all ABS concrete penetrations with foam wrap per the UPC. -Add 2"vent to downstairs toilet per the UPC chap 9.-Add minimum 11/2"vent to downstairs lav per UPC chap 9 and 10-Replace 4"San tee on its back with a non directional clean-out tee per the UPC chap 7 for building clean-out.-Replace San tee on back below flood rim of toilets for dry vent and wet vent on upstairs toilets UPC chap 7 and 9.-Foam wrap all ABS penetration and points of contact with slab per the UPC 312.2-Install clean-out on kitchen drain above or below trap arm per the UPC chap 7. I Printed:Wednesday, 24 April, 2024 1 of 2 rk SUPERION