1105 13TH ST 2024-06-07 - Laserfiche WebLink

1) WELDING PROCEDURES Please refer to www.AnvilStar.com or latest catalog for recommended hole size and welding practice. 11) THREAD MAKE-UP AND INSTALLATION A) For use in systems installed in accordance with all applicable standards or codes. (See Section III, Item C) B) Before starting the job of making nipples or sprinklers into steel threads of the above fittings, insure that no dirt or weld spatter is in the threads and no burn -through damaged the threads. Then count the number of fully developed male threads on the nipple or sprinkler to be installed into the fittings. Compare number of threads counted to the number of required fully developed threads as shown in the thread chart located on the back of this sheet. If thread count is correct, proceed with installation (Step C), if thread count does not match, check nipple or sprinkler for proper thread gage measurement and discard if not to ANSI B1.20.1 / ISO-7R/RC specification. C) The use of an anaerobic pipe thread sealant is preferred for thread make up when connecting to another pipe fitting or nipple. If attach- ing a sprinkler head, please refer to the manufacturer's installation instructions and apply pipe thread sealant only to male threads of the sprinkler. D) If either of the above fails to allow the sprinkler or nipple to make- up to a minimum of full threads, do not over tighten. Instead back the sprinkler or nipple out of the fitting. Clean any debris and/or pipe sealant from both the male and female threads. Gauge both the male threads of the sprinkler or nipple and the female threads of the Tee -Let with ANSI B1.20.1 / ISO-7R/RC. Specification for Tapered Pipe Threads. The same procedure would apply if a leak has been detected. If within tolerance, reapply the anaerobic pipe sealant or Teflon TM tape and make -on to the required length. Refer to the pipe chart on page B for correct make-up lengths. Allow twenty-four hours for setting. III) GENERAL INFORMATION A) APPROVALS AND STANDARDS Merit Manufacturing Tee -Lets are listed by the Underwriters Laboratories, Inc. and approved by the Factory Mutual Research Corporation (FM). B) TECHNICAL DATA Merit Manufacturing Tee -Lets are rated for use at a maximum ser- vice pressure of 300 psi. The threads conform to ANSI B1.20.1 / ISO-7R/RC. C) WARNING Merit Manufacturing Tee -Lets described herein must be installed and maintained in compliance with this document as well as the applicable standards of the National Fire Protection Association in addition to the standards for any other authorities having jurisdiction D) DIMENSIONAL DATA See pages 5 - B. E) WARRANTY AND DISCLAIMER Seller warrants for one year from the date of shipment Sellers manufactured products to the extent that Seller will replace those having defects in material or workmanship when used for the MERIT® Weld-MiserTm Tee -Let® Installation (coat.) Welding Outlet Fittings purpose and in the manner which Seller recommends. If Seller examination shall disclose to its satisfaction that the products are defective, and an adjustment is required, the amount of such adjustment shall not exceed the net sales price of the defective products only and no allowance will be made for labor or expense of repairing or replacing defective products or workmanship of damage resulting from the same. Seller warrants the products which it sells of other manufacturers to the extent of the warranties of their respective makers. Where engineering design or fabrication work is supplied. Buyers acceptance of Sellers design or of delivery of work shall relieve Seller of all further obligation, other than expressed in Seller's product warranty. THIS IS SELLER'S SOLE WARRANTY. SELLER MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FOR A PARTICULAR PURPOSE WHICH EXCEED SELLER'S AFORESTATED OBLIGATION ARE HEREBY DISCLAIMED BY SELLER AND EXCLUDED FROM THIS WARRANTY. Seller neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of its engineering designs or products. This warranty shall not apply to any products or parts of products which (a) have been repaired or altered outside of Sellers factory, in any manner: (b) have been subjected to misuse, negligence or accidents; (c) have been used in a manner contrary to Sellers instructions or recommendations. Seller shall not be responsbile for design errors due to inaccurate or incomplete information supplied by Buyer or its representatives. F) SELLER'S LIABILITY: Seller will not be liable for any Toss, damage, cost of repairs, incidental or consequential damages of any kind, whether based upon warranty (except for the obligation accepted by Seller under "Warranty" above), contract or negligence, arising in connection with the design, manufacture, sale, use or repair of the products or of the engineering designs supplied to Buyer. G) RETURNS: Seller cannot accept return of any products unless its written permission has been first obtained, in which case same will be credited subject to the following (a) All material returned must, on its arrival at Sellers Plant, be found to be in first-class condition; if not, cost of putting in saleable condition will be deducted from credit memoranda; (b) A handling charge deduction of twenty percent (20%) will be made from all credit memoranda issued for material returned; (c) Transportation charges, if not prepaid will be deducted from credit memoranda. H) RETURN OF MATERIAL No Products sold by Ment may be returned without Merit's written consent. All products returned are subject to a handling charge plus freight in both directions and charges for any required reconditioning, unless otherwise specified in writing by Merit. 1) COMPLETE TERMS AND CONDITIONS CAN BE FOUND AT www.anvilstar.com AMStar- Merit-1.10 —11 — fireN ua% pvivan ar Mvil Inwm do al