Laserfiche WebLink
INSTALLATION • • ' WOOD & STEEL <br /> INSTALLATION STEP INTO WOOD&STEEL: INSTALLATION STEP •' •MTO WOOD&STEEL: <br /> 1.Insert the appropriate nut driver into a 3/8"or 1/2°portable drill. 1.Insert the appropriate nut driver into a 3/8"or 1/2"portable drill. <br /> 2.Insert the SAMMYS®into the#14(black)nut driver(p/n 8113910).Drill 2.Insert the SAMMYS into the#14SW(red)nut driver(p/n 8114910).With drill <br /> should be in a vertical position. unit in a horizontal position and at a right angle to the structural member, <br /> begin installation. <br /> 3.Push the face of the nut driver tight to the member.Begin installation when <br /> the nut driver spins freely on the SAMMYS,stop drill and remove. 3.When the nut driver spins freely on the SAMMYS,stop the drill and <br /> remove. <br /> 4.The SAMMYS is now ready to receive 1/4°318",1/2"or metric <br /> all thread rod,bolt stock.(The 1/2"requires the#14SW red nut driver) 4.The unit is now ready to receive 1/4",3/8",M10,M8 or metric all thread rod or <br /> bolt stock. <br /> Note:When installing DSTR,follow the above instructions,then add retainer <br /> nut and torque to 20 inch lbs.for maximumpullout in purlin steel. Note:When installing SWDR,follow the above instructions,then add retainer <br /> nut and torque to 20 inch lbs.for maximum pullout in purlin steel. <br /> INSTALLATION • FOR CONCRETE <br /> INSTALLATION STEPS- =INTO CONCRETE: INSTALLATION STEPS]= INTO CONCRETE: <br /> 1.Using an SDS 250 carbide tip bit or a HEX RECEIVER with a #250 1.Using an SDS 250 carbide tip bit or a HEX RECEIVER with a #250 <br /> carbide tip bit,pre-drill the concrete member to a depth of 2"with a carbide tip bit,pre-drill the concrete member to a depth of 2"with a hammer/ <br /> hammer/rotary hammer drill set on impact mode. rotary hammer drill set on impact mode. <br /> 2.After pre-drilling has been completed,install the SLEEVE TOOL over 2.After pre-drilling has been completed,install the SLEEVE TOOL <br /> the bit(the bit should remain in the drill),and insert the#14(black) over the bit(the bit should remain in the drill),and insert the#14SW(red) <br /> nut driver(p/n 8113910)into the opposite end(see Vertical Installation nut driver(p/n 8114910)into the opposite end. <br /> note above). <br /> 3.Insert the SWC screw into the nut driver. <br /> 3.Insert the CST screw into the nut driver. <br /> 4.Place tip of screw into the pre-drilled hole,turn impact/drill unit to <br /> 4.Place tip of screw into the pre-drilled hole,tum impact/drill unit to drill drill mode and begin insertion.When the nut driver spins free on the <br /> mode and begin insertion.When the nut driver spins freely on the SWC screw,installation is complete.Stop and remove drill. <br /> CST screw,installation is complete.Stop and remove drill. <br /> 5.The SWC screw is ready to receive 1/4°3/8"or metric all thread rod <br /> 5.The concrete screw is ready to receive 1/4°3/8°1/2",or metric all or bolt stock. <br /> thread rod or bolt stock.(#14SW red nut driver used with 1/2"screw) <br /> Note:Use a 1200 maximum RPM drill for installation. <br /> Note:Use a 1200 maximum RPM drill for installation. <br /> Note:Do not install concrete screws while the drill unit is in impact mode— <br /> Note:Do not install concrete screws while the drill unit is in impact mode— doing so will destroy the pullout factor of the fastener <br /> doing so will destroy the pullout factor of the screw. <br /> SPECIAL NUT DRIVER SYSTEM:The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time.When the face of the driver comes into <br /> contact with the material you are installing into,continue drilling until nut driver spins free.Installation is then complete.Warranty requires the use of the appropriate nut driver for installations. <br /> 3 To find a distdbutor near you,call 800-848-5611 <br />