Laserfiche WebLink
GENERAL NOTES AERIAL VIEW <br /> CODE AND STANDARDS <br /> "ALL WORK SHALL COMPLY WITH 2017 NATIONAL ELECTRIC CODE(NEC),2015 INTERNATIONAL BUILDING CODE BLUE RAVEN <br /> (IBC),2015 INTERNATIONAL RESIDENTIAL CODE(IRC),2015 INTERNATIONAL PLUMBING CODE(IPC),AND ALL STATE - <br /> AND LOCAL BUILDING,ELECTRICAL,AND PLUMBING CODES. fa'%111�1 1 ' <br /> 2.DRAWINGS HAVE BEEN DETAILED ACCORDING TO UL LISTING REQUIREMENTS. • .� Y_ <br /> 1403 N. Research Way <br /> SITE NOTES/OSHA REGULATION r •• Orem, UT 84097 <br /> 1.A LADDER SHALL BE IN PLACE FOR INSPECTION IN COMPLIANCE WITH OSHA REGULATIONS. dab 800.377.4480 <br /> 2.THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS A UTILITY INTERACTIVE SYSTEM. r� WWW.BLUERAVENSOLAR.COM <br /> 3.THE SOLAR PV INSTALLATION SHALL NOT OBSTRUCT ANY PLUMBING,MECHANICAL,OR BUILDING ROOF VENTS. <br /> 4.ROOF COVERINGS SHALL BE DESIGNED,INSTALLED,AND MAINTAINED IN ACCORDANCE WITH THIS CODE ANDCONFIDENTIAL-THE INFORMATION <br /> THE APPROVED MANUFACTURER'S INSTRUCTIONS SUCH THAT THE ROOF COVERING SHALL SERVE TO PROTECT , 1 i HEREIN CONTAINED SHALL NOT BE <br /> THE BUILDING OR STRUCTURE. ' , .�, USED FOR THE BENEFIT OF ANYONE <br /> EXCEPT BLUE RAVEN SOLAR NOR <br /> SHALL IT BE DISCLOSED IN WHOLE OR <br /> SOLAR CONTRACTOR IN PART TO OTHERS OUTSIDE <br /> 1.MODULE CERTIFICATIONS WILL INCLUDE UL1703,IEC61646,IEC61730. RECIPIENTS ORGANIZATION,EXCEPT <br /> 2.IF APPLICABLE,MODULE GROUNDING LUGS MUST BE INSTALLED AT THE MARKED GROUNDING LUG HOLES PER IN CONNECTION WITH THE SALE AND <br /> THE MANUFACTURER'S INSTALLATION REQUIREMENTS. �' 1 ► USE OF THE RESPECTIVE EQUIPMENT, <br /> 3.AS INDICATED BY DESIGN,OTHER NRTL LISTED MODULE GROUNDING DEVICES MAY BE USED IN PLACE OF WITHOUT THE WRITTEN PERMISSION <br /> STANDARD GROUNDING LUGS AS SHOWN IN MANUFACTURER DOCUMENTATION AND APPROVED BY THE AHJ. f roOF BLUE RAVEN SOLAR LLC. <br /> 4.CONDUIT AND WIRE SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND ARE NOT MEANT TO � <br /> LIMIT UP-SIZING AS REQUIRED BY FIELD CONDITIONS. , <br /> 5.CONDUIT POINT OF PENETRATION FROM EXTERIOR TO INTERIOR TO BE INSTALLED AND SEALED WITH A NAB C E P <br /> SUITABLE SEALING COMPOUND. • �• <br /> 6.DC WIRING LIMITED TO MODULE FOOTPRINT W/ENPHASE AC SYSTEM. <br /> 7.ENPHASE WIRING SYSTEMS SHALL BE LOCATED AND SECURED UNDER THE ARRAY W/SUITABLE WIRING CLIPS. CERTIFIED] <br /> 8.MAX DC VOLTAGE CALCULATED USING MANUFACTURER PROVIDED TEMP COEFFICIENT FOR VOC UNLESS NOT PV INSTALLATION <br /> AVAILABLE. `�{� <br /> 9.ALL INVERTERS,MOTOR GENERATORS,PHOTOVOLTAIC MODULES,PHOTOVOLTAIC PANELS,AC r PROFESSIONAL <br /> PHOTOVOLTAIC MODULES,DC COMBINERS,DC-TO-DC CONVERTERS,SOURCE CIRCUIT COMBINERS,AND Scott Gurney <br /> CHARGE CONTROLLERS INTENDED FOR USE IN A PHOTOVOLTAIC POWER SYSTEM WILL BE IDENTIFIED AND #PV-011719-015866 <br /> LISTED FOR THE APPLICATION PER NEC 690.4(B). <br /> 10.ALL SIGNAGE TO BE PLACED IN ACCORDANCE WITH LOCAL BUILDING CODE. CONTRACTOR: <br /> 11.TERMINALS AND LUGS WILL BE TIGHTENED TO MANUFACTURER TORQUE SPECIFICATIONS(WHEN PROVIDED) f BRS FIELD OPS <br /> IN ACCORDANCE WITH NEC CODE 110.14(D)ON ALL ELECTRICAL CONNECTIONS. <br /> 800-377-4480 <br /> EQUIPMENT LOCATIONS <br /> 1.PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT r �• �` <br /> WILL BE PROVIDED AS PER SECTION NEC 110.26. <br /> 2.EQUIPMENT INSTALLED IN DIRECT SUNLIGHT MUST BE RATED FOR EXPECTED OPERATING TEMPERATURE AS • �* ` <br /> SPECIFIED BY NEC 690.31(A)AND NEC TABLE 310.15(B). • U <br /> 3.ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL ACCORDING TO NEC i /' Q U <br /> APPLICABLE CODES. m r Z <br /> 4.ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED FOR OUTDOOR USAGE WHEN APPROPRIATE. • Oco Y <br /> Ii— O 00 <br /> PROJECT INFORMATION: CN <br /> Q � 00 <br /> a 0-) LID r` <br /> NUMBER OF STORIES: 1 <br /> CONDUIT RUN: Interior LL N <br /> ECOBEE QTY: 1 <br /> Z > <br /> LIGHT BULB QTY: 189 c Q ) <br /> PV METER: Not Required DESIGN CRITERIA SITE SPECIFICATIONS SHEET INDEX x F- F- <br /> ROOF TYPE (1) INFORMATION: O z p N N <br /> ROOF TYPE: Comp Shingle WIND SPEED: 110 mph z CONSTRUCTION -V-B PV1 -COVER SHEET F_ T N <br /> GROUND SNOW LOAD: 15 Ib/ft ZONING: RESIDENTIAL PV2-SITE PLAN N <br /> FRAMING TYPE: Rafter WIND EXPOSURE FACTOR: C PV3- ROOF PLAN :3M p> U U <br /> SHEATHING TYPE: TONGUE AND GROOVE SEISMIC DESIGN CATEGORY: D PV4-STRUCTURAL U J (0 LU Q IO <br /> ATTACHMENT: SFM Infinity Flashkit <br /> " rait/64" OC Landscape PV5- ELECTRICAL 3-LINE DIAGRAM DRAWING BY: <br /> NUMB�R06ATTACHMEN�TS: 51 SCOPE OF WORK PV6- ELECTRICAL CALCULATIONS <br /> PV7-WARNING LABELS AND LOCATIONS Michael Honey <br /> ROOF TYPE (2) INFORMATION (IFAPPLICABLE): INSTALLATION OF UTILITY INTERACTIVE PHOTOVOLTAIC SOLAR SYSTEM AND ANY (ALL OTHER SHEETS AS REQUIRED) <br /> *SEE PV4.2 NECESSARY ADDITIONAL WORK NEEDED FOR INSTALLATION. <br /> SS- PRODUCT SPEC. SHEETS PLOT DATE: <br /> January 3, 2024 <br /> PROJECT NUMBER: <br /> SYSTEM TO BE INSTALLED INFORMATION: UTILITY COMPANY: 820030 <br /> DC SYSTEM SIZE: 7.98 kW DC Snohomish County Public Utilities District <br /> AC SYSTEM SIZE: 5.985 kW AC (PUD) SHEET NAME: <br /> MODULE TYPE: (19) REC Solar REC420AA PURE-R COVER SHEET <br /> INVERTER TYPE: Enphase IQ7X-96-2-US <br /> MONITORING: Enphase IQ Combiner4 X-IQ-AM1-240-4 PERMIT ISSUER: REVISION: PAGE NUMBER: <br /> City of Everett B PV 1 <br />