10121 25TH AVE SE 2024-08-02 - Laserfiche WebLink

Lumio LUMIO 1550 DIGITAL DR,LEHI,UT 84043,USA SYSTEM INFO (11)Q CELLS Q.PEAK DUO BLK ML-G10+ (400W) (11)ENPHASE IQ8PLUS-72-2-US(240V) DC SYSTEM SIZE:4.400 kWDC NM; BONDING CONNECTIONS&GROUNDING PATHS �� APPENDIX A ; E AC SYSTEM SIZE:3.300kWAC on----- INSTALLATION E on [m))U M 0 UT EM ; ------- ---------------------- ----- -- ----------------------------------GUIDE-:-------- - PAG-------- ----------------------------------------------------------------------- ------SYST-----------CERTIFICATIONPAGE----------------------------- The NXT UMOUNT system has been certified and listed to the UL 2703 standard(Rack Mounting Systems and Clamping Devices for Flat-Plate Photovoltaic Modules REVISIONS and Panels).This standard included electrical grounding,electrical bonding,mechanical load and fire resistance testing. DESCRIPTION DATE REV RACKING SYSTEM GROUND Ground Lug w/Bare Copper BONDING PP Wire MICROINVERTER SYSTEM LEVEL FIRE CLASSIFICATION Note:Only one lug per mode MOUNTS The system fire class rating requires installation in the manner specified in the NXT UMOUNT Installation Guide.NXT UMOUNT has been classified to the system level row required —� fire portion of UL 2703.NXT UMOUNT has achieved system level performance for steep sloped roofs.System level fire performance is inherent in the NXT UMOUNT _ design,and no additional mitigation measures are required.The fire classification rating is only valid on roof pitches greater than 2:12(slopes>2 inches perfoot,or - 9.5 degrees).The system is to be mounted over fire resistant roof covering rated forthe application.There is no required minimum or maximum height limitation above the roof deck to maintain the system fire rating for NXT UMOUNT.Approved Module Types &System Level Fire Ratings are listed below: PROJECT NAME&ADDRESS BONDING RAILSPLICE Module Type System Level Rre Rating I Rail Direction Module Orientation Type 1,2,3 with metal frame,10 ClassA Parallel OR Perpendicular to Ridge Landscape OR Portrait Q with metal frame,19,22,25,29, U) &30 i 00 ------ MECHANICAL LOADTESTMODULES O BONDING The modules selected for UL 2703 mechanical load testing were selected to represent the broadest range possible for modules on the market.The tests performed 00 COMBO covers module frame thicknesses greater than or equal to 1.0 mm,single and double wall frame profiles(some complex frame profiles could require further analysis to O� CLAMPS ALTERNATE determine applicability),and clear and dark anodized aluminum frames. PV modules may have a reduced load rating,independent of the NXT UMOUNT rating.Please O ROW-TO-ROW ;1, consult the PV module manufacturer's installation guide for more information. Z N j O BONDING METHOD O Tested Module UL2703 Certification Load Ratings I Tested Loads Tested Module Area 00 p SunPower SPR-A440-COM Down:50 psf,Up:50 psf,Slope:15 psf Down:75 psf,Up:75 psf,Slope:23 psf 21.86 sq ft U U C) W CD J inko JKM-xxxM 72HL4-V Down:50.12 psf,Up:22.28 psf,Slope:8 psf Down:75.19 psf,Up:33.42 psf,Slope:12 psf 27.76 sq ft } Z ' 0� O W a LL] N NOTE:Jinko module mechanical load values do not apply to the following part numbers C, LO (shown on page 3);RLSPLCM2,SBUTYLM1,SBUTYLDI,SHCLMPM2,&SHCLMPD2 J W C) W W U uj N UL2703 CERTIFICATION MARKING: � W' W L Unirac NXT UMOUNT is listed to UL 2703.Certification marking is embossed on uNIRAt U) O W all Combo Clamps as shown. Labels with additional certification information 0 > Z are provided with clamps and must be applied to the NXT UMOUNT Rail at the d Q d edge of the array. ® Q IF CIU Note:This racking system may be used to ground and/or mount a PV module C 8 (— complying with UL1703/UL61730 only when the specific module has been 266909 N evaluated for grounding and/or mounting in compliance with the included instructions. N O T_ DATE:7/1/2023 SHEET NAME EQUIPMENT LSPECIFICATIONS SHEET SIZE ANSI B 11" X 17" SHEET NUMBER PV-16