Laserfiche WebLink
- <br /> 3. Remove plastic cover from gas pressure regulator cap. 4. Gas orifice spuds are stamped with a number on the side. <br /> 4. Turn gas pressure regulator cap counterclockwise with a Replace the LP gas orifice spud with the correct Natural gas <br /> 3'combination wrench to remove. orifice spud. <br /> NOTE:Do not remove the spring beneath the cap. <br /> ra,i, <br /> o <br /> Q Side view before <br /> NI ic,...........„, `A <br /> A 0 t. t <br /> NV/ "4 [— VI <br /> ar"" \ d d <br /> A.Stamped number <br /> B 0 E Refer to the following chart for the correct Natural gas orifice <br /> o ell spud placement. <br /> o Natural Gas Orifice Spud Chart° <br /> Nb, v. / .1116.1.. <br /> �'� � ■ ' Burner Rating Color Size ID <br /> i"{ �'114�'' Number <br /> o ® ������ 18,000 BTU Yellow/Blue 2.16 mm N216 <br /> 1 C Side view after 0 17,000 BTU Red/Magenta 2.10 mm N210 <br /> 15,000/15,500 BTU RedBlack 2.00 mm N200 <br /> A.Plastic cover 14,200 BTU Red/Orange 1.90 mm N190 <br /> B.Gas pressure regulator cap with hollow end facing out 13,000/13,500 BTU Red/Blue 1.85 mm N185 <br /> C.Gas pressure regulator cap with solid end facing out 12,000/12,500 BTU Red/Yellow 1.80 mm N180 <br /> D.Washer <br /> E.Gas pressure regulator cap 9,500 BTU Red/Brown 1.55 mm N155 <br /> 8,000 BTU Red/White 1.40 mm N140 <br /> 5. Turn over the gas pressure regulator cap and reinstall on 5,000 BTU Red/Brass 1.10 mm N110 <br /> regulator so that the solid end faces out and the marking <br /> "4 NG"is facing the direction shown in the above drawing. NOTE:Refer to the Model Number and Serial Number Plate <br /> 6. Replace plastic cover over gas pressure regulator cap. located on the oven frame behind the top left side of the oven <br /> door for proper sizing of spuds for each burner location. <br /> To Convert Surface Burners(LP Gas to Natural Gas) 5. Place LP gas orifice spuds in plastic parts bag for future use <br /> and keep with package containing literature. <br /> 1. Remove burner cap. 6. Replace the burner base using both screws. <br /> 2. Using a Phillips or Quadrex'screwdriver,remove the burner 7. Replace burner cap. <br /> base. <br /> NOTE:Reinstall one of the screws through the range cooktop 8. Repeat steps 1-7 for the remaining burners. <br /> to hold the orifice spud holder in place while removing and replacing the orifice spuds. To Convert Oven Bake Burner(LP Gas to Natural Gas) <br /> 3. Apply masking tape to the end of a 3/42"(7 mm)nut driver to 1. Remove the oven racks. <br /> help hold the gas orifice spud in the nut driver while changing 2. Remove 2 screws at the rear of the oven bottom. <br /> it.Press nut driver down onto the gas orifice spud and <br /> remove by turning it counterclockwise and lifting out.Set gas 3. Lift the rear of the oven bottom up and back until the front of <br /> orifice spud aside. the panel is away from the front frame.Remove from oven <br /> and set it aside on a covered surface. <br /> C A <br /> A i <br /> . <br /> D °� <br /> o ,, <br /> cD <br /> A.Orifice spud <br /> B.Orifice spud holder <br /> C.Screw A.Screws <br /> D.Spark electrode B.Oven bottom <br /> 18 <br />