Laserfiche WebLink
MCI CONSTRUCTION DETAILS/TYPICALS verizonl <br /> PROJECT: <br /> GENERAL AERIAL CONSTRUCTION DETAILS 1801AVA0.9 ROWI EVT 0902 <br /> EVERETT <br /> TYPICAL DETAIL "A" TYPICAL DETAIL "C" 5828GLENWOODAVE <br /> POLE ARRANGEMENT FOR TYPICAL DETAIL "B" TYPICAL CABLE&HARDWARE EVERETT,WA <br /> AERIAL TO BURIED INSTALLATION <br /> POLE ARRANGEMENT FOR REPEATER <br /> 2 1 12" <br /> OR HANDHOLE LOCATION 10 0" 10" <br /> Z <br /> GUY <br /> O <br /> }^ GROUND WIRE CLAMP LASHING <br /> CABLE LASHING 2 I X r2" <br /> WIRE CLAMP <br /> P4" WIRE CLAMP Z) <br /> z <br /> STAINLESS STEEL LASHER 0 O <br /> STAINLESS STEEL LASHER (X—MIN.OF 20 TIMES < 0 <br /> POLE TOP VIEW CABLE SUPPORT AND.50"SPACER 24 THE CABLE DIA.) CABLE SUPPORT AND CAUTION TAG Z <br /> 2"GALV.STEEL FIBER OPTIC CABLE <br /> X .50"SPACER U E- <br /> U-GUARD CAUTION TAG BLACK IN COLOR W <br /> I+ GROUND LEVEL CABLE CLAMP #6 INSULATED COPPER WIRE Z W <br /> FIBER OPTIC CABLE Z <br /> BLACK IN COLOR POLE AND 10'X.75"COPPER CLAD POLE Q J <br /> CABLE POLE TOP VIEW GROUND ROD J Q <br /> FFOR <br /> U-GUARD GROUND LEVEL Ca Lu D_ w C7 <br /> ND U-GUARD MIN.6" GROUND LEVEL 6"MIN. Q <br /> CONDUIT GROUND LEVEL _ <br /> ONDUIT PL.U-GUARDCONDUIT ON QUARTER GROUNDEVERY .25MILE <br /> SURFACE TO ON POLE NEAREST AT STRAND TO SHEATH <br /> CONDUIT ADAPTER. 42" REPEATER OR SPLICE H.H. O <br /> MIN. 4"PVC BEND BOND LOCATION <br /> (36"RADIUS) ■■■ <br /> TYPICAL DETAIL "D" <br /> 7F' <br /> CONDUIT TO HH <br /> SUSPENSION STRAND-PULL TOWARD OR REPEATER TYPICAL DETAIL "F" FORESITE <br /> POLE-LESS THAN 5 FEET <br /> TYPICAL ARRANGEMENT OF <br /> Foresite Group,Inc wlwww.fg-inc.nec <br /> CURVED WASHER noon EC—CI,„ea n. <br /> TYPICAL DETAIL "E" BUI[e 400 f 1 n 30.887.6002E <br /> CABLE SUSPENSION ao,ein Tx�e�o: <br /> BOLT SUSPENSION STRAND-PULL AWAY <br /> CABLE GUIDE APPROX.� CABLE LASHER <br /> 2 GUY HOOK FROM POLE-5 FEET OR MORE 4" <br /> 8" <br /> SPACER NUT <br /> POLE TOP f GUY <br /> 18"PREFERABLY <br /> BUT NO LESS <br /> THAN 10" TO CABLE REEL 7 CABLE <br /> CURVED WASHER CABLESUSPENSION 1 <br /> BOLT / !/ <br /> GUY .625" CABLE SUSPENSION <br /> BOLT CURVED WASHER SNAP <br /> 2 GUY HOOK PULLING LINE <br /> CABLE SUSPENSION <br /> CLAMP SPACER NUT DATE: 02/22/2019 <br /> .8125" X 2"ROUND <br /> WASHER GUY ENGINEER: F.Colon <br /> DRAWN BY: S.Dickson <br /> CORNER SUSPENSION <br /> TYPICAL DETAIL "G" CLAMP TYPICAL DETAIL "I" REVISIONS <br /> JOINING 045 LASHING WIRE ANCHOR&DOWN GUY DATE DESCRIPTION INITIAL <br /> I'I <br /> TYPICAL DETAIL "H" GUY <br /> LASHING WIRE GRIP AND CLAMP CABLE <br /> 7 11 <br /> FORMING WIRE OVER FORMING LASHING WIRE <br /> STUD OF CLAMP AROUND STRAND CLASHING <br /> WIRE GRIP Excr=aT as MAY BE oTHENwIsr=aRovioEo BY coNTRacT <br /> REMOVE ANY SLACK IN THE LASHING FORM THE LASHING WIRE AROUND THE 1 ST LASHING WIRE THESE DRAWINGS AND SPECIFICATIONS SHALL REMAIN TN <br /> PROPERTY OF MCI COMMUNICATIONS SERVICES,INC..BOT <br /> WIRE BY MAINTAINING A PULL ON THE STRAND AND PLACE IT BELOW THE STUD BEING ISSUED IN STRICT CONFIDENCE AND SHALL NOT B <br /> SHOULDER 2ND LASHING WIRE REPRODUCED, COPIED, OR USED FOR ANY PURPOSE <br /> WIRE AND TAPPING THE STRAND AND BETWEEN THE SECOND WASHER WITHOUT SPECIFIC WRITTEN PERMISSION. <br /> SHARPLY. THEN FORM THE WIRE OVER AND STUD SHOULDER. CLAMPING NUT TERMINATING NUT I EX.GRADE <br /> THE STUD AND TIGHTEN THE NUT. III I SCALE <br /> CUT THE FREE END OF THE LASHING 1 <br /> WIRE OFF.75"BEYOND THE END OF THE HORIZONTAL: N/A <br /> CLAMP. THREADED STUD 1ST WASHER <br /> .75"X 8'DEAD END VERTICAL: N/A <br /> NOTE: GROOVED PLATES 2ND WASHER E/W 10"SCREW ANCHOR <br /> LASHING WIRE <br /> SHOULD FOLLOW LAY <br /> OF STRAND WIRES UNDER SHEET: D-01 <br /> GRIP. I j <br />