Laserfiche WebLink
MCI CONSTRUCTION DETAILS/TYPICALS verizon,' <br /> PROJECT: <br /> GENERAL AERIAL CONSTRUCTION DETAILS 1801AVA0.2 ROWI EVT 1118 <br /> EVT <br /> TYPICAL DETAIL "A" TYPICAL DETAIL "C" 'r`T'°`"T'°" <br /> POLE ARRANGEMENT FOR TYPICAL DETAIL "B" TYPICAL CABLE&HARDWARE EVERETT,WA <br /> AERIAL TO BURIED INSTALLATION <br /> 2 <br /> POLE ARRANGEMENT FOR REPEATER <br /> I^ OR HANDHOLE LOCATION 10 1z" <br /> 1 <br /> I 10" 10- 1 u <br /> z <br /> GUY X GROUND WIRE CLAMP CABLE LASHING 0 <br /> CABLE LASHING 2 2" WIRE CLAMP () <br /> 4" WIRE CLAMP <br /> L p LU <br /> ~ z <br /> X-MIN.OF 20 TIMES STAINLESS STEEL LASHER z F <br /> STAINLESS STEEL LASHER ( Z � <br /> 24" CABLE SUPPORT AND Q <br /> POLE TOP VIEW CABLE SUPPORT AND.50"SPACER X THE CABLE DIA.) CAUTION TAG � U <br /> 2"GALV.STEEL .50"SPACER FIBER OPTIC CABLE � U Q U <br /> U-GUARD CAUTION TAG BLACK IN COLOR � U) <br /> I+ GROUND LEVEL FIBER OPTIC CABLE CABLE CLAMP #6 INSULATED COPPER WIRE Z DO } <br /> BLACK IN COLOR CABLE POLE AND 10'X.75"COPPER CLAD POLE Q 0_ <br /> NOTES: U-GUARD POLE TOP VIEW GROUND ROD GROUND LEVEL d w <br /> 7 <br /> 1.EXTEND U-GUARD MIN.6" GROUND LEVEL 6"MIN. 0 Q <br /> CONDUIT BELOW GROUND LEVEL <br /> 2.FOR CONDUIT PL.U-GUARD CONDUIT ON QUARTER GROUND EVERY .25 MILE � <br /> BELOW SURFACE TO ON POLE NEAREST AT STRAND TO SHEATH <br /> CONDUIT ADAPTER. 42" REPEATER OR SPLICE H.H. O <br /> MIN. 4"PVC BEND BOND LOCATION <br /> (36"RADIUS) <br /> TYPICAL DETAIL "D" <br /> CONDUIT TO HH <br /> SUSPENSION STRAND-PULL TOWARD OR REPEATER TYPICAL DETAIL 'IF" FORESITE <br /> POLE-LESS THAN 5 FEET <br /> TYPICAL ARRANGEMENT OF <br /> Fa�vinc w www.lq-inc.ntt <br /> CURVED WASHER CABLE LASHER AND CABLE GUIDE <br /> 300o Eu G—P.C..'C—n St. 33 <br /> TYPICAL DETAIL "E" sn..00 1339.88]6029 <br /> CABLE SUSPENSION Au:nn,T%]e]o2 <br /> BOLT SUSPENSION STRAND-PULL AWAY <br /> CABLE G CABLE LASHER <br /> 2 GUY HOOK FROM POLE-5 FEET OR MORE <br /> 8" <br /> SPACER NUT <br /> POLE TOP f GUY <br /> 18"PREFERABLY <br /> BUT NO LESS <br /> THAN 10" TO CABLE REEIV CABLE <br /> CURVED WASHER CABLE SUSPENSION BOLT GUY .625" CABLE SUSPENSIONCURVED WASHER 2GUYHOOK LINE <br /> CABLE SUSPENSION <br /> CLAMP SPACER NUT DATE: 05/17/2019 <br /> .8125" X 2"ROUND <br /> WASHER GUY ENGINEER: F.Colon <br /> DRAWN BY: S.Dickson <br /> TYPICAL DETAIL "G" CORNERSUSPECLAM TYPICAL DETAIL "I" REVISIONS <br /> CLAMP <br /> JOINING 045 LASHING WIRE ANCHOR&DOWN GUY DATE DESCRIPTION INITIAL <br /> IF, <br /> TYPICAL DETAIL "H" GUY <br /> LASHING WIRE GRIP AND CLAMP CABLE <br /> 7 <br /> FORMING WIRE OVER FORMING LASHING WIRE <br /> STUD OF CLAMP AROUND STRAND CLASHING <br /> WIRE GRIP ExCEPT As Inv BE OTHERWISE PROVIDED BY CONTRACT <br /> REMOVE ANY SLACK IN THE LASHING FORM THE LASHING WIRE AROUND THE 1 ST LASHING WIRE I THE =Y F1 05 ANO I-WICACATIONs SHALL RETAIN THE <br /> PROPERTY OF MCI COMMUNICATIONS SERVICES.INC..BOT <br /> WIRE BY MAINTAINING A PULL ON THE STRAND AND PLACE IT BELOW THE STUD BEING ISSUED w STRICT CONFIDENCE AND SHALL NOT R <br /> SHOULDER 2ND LASHING WIRE REPRODUCED, COPIED, OR USED FOR ANY PURPOSE <br /> WIRE AND TAPPING THE STRAND AND BETWEEN THE SECOND WASHER WITHOUT SPECIFIC WRITTEN PERMISSION. <br /> SHARPLY. THEN FORM THE WIRE OVER AND STUD SHOULDER. CLAMPING NUT TERMINATING NUT I EX.GRADE <br /> THE STUD AND TIGHTEN THE NUT. `L I SCALE <br /> CUT THE FREE END OF THE LASHING 1 <br /> WIRE OFF.75"BEYOND THE END OF THE HORIZONTAL: N/A <br /> CLAMP. THREADED STUD IS WASHER <br /> .75"X 8'DEAD END VERTICAL: N/A <br /> NOTE: GROOVED PLATES 2ND WASHER E[W 10"SCREW ANCHOR <br /> LASHING WIRE <br /> SHOULD FOLLOW LAY <br /> OF STRAND WIRES UNDER SHEET: D-01 <br /> GRIP. I j <br />