5510 S 3RD AVE 2024-11-08 - Laserfiche WebLink

11� EZ SOLAR JB-3 EZf SOLAR Installation Manual BLUE RAVE R Specification Sheet making solar simple, PV Junction Box for Composition/Asphalt Shingle Roofs making solar simple, PV Junction Box for Composition/Asphalt Shingle Roofs A. System Specifications and Ratings o { • Maximum Voltage: 1,000 Volts QUICK AR GUIDE WATCH INSTALLVIDEO • Maximum Current: 80 Amps • Allowable Wire: 14 AWG—6 AWG • Spacing: Please maintain a spacing of at least 1/2" between uninsulated live parts and fittings for conduit, armored cable, and uninsulated live parts of opposite polarity. • Enclosure Rating:Type 3R • Roof Slope Range: 2.5—12:12 = • Max Side Wall Fitting Size: 1" • Max Floor Pass-Through Fitting Size: 1" • Ambient Operating Conditions: (-35°C) - (+75°C) r� • Compliance: ` -JB-3: UL1741, CSA C22.2 No. 290 J -Approved wire connectors: must conform to UL1741 • System Marking: Interek Symbol and File#5025824 Y g Y - • Periodic Re-inspections: If re-inspections yield loose components, loose fasteners, or any corrosion between components, components that are found to be affected are to be replaced immediately. Slide junction box onto the rail at desired 1.Attach the SS Clamps to the Junction Box. location and secure the box with the SS Table 1:Typical Wire Size,Torque Loads and Ratings Pro Tip: Compress the SS Clamps against the back wall and rock into place. Clamps. Let the JB-3 lay on the roof with the 1 Conductor 2 Conductor Torque hex head rotated to the top. Type NM Inch Lbs Voltage Current ABB ZS6 terminal block 10-24 awg 16-24 awg Sol/Str 0.5-0.7 6.2-8.85 600V 30 amp ABB ZS10 terminal block 6-24 awg 12-20 awg Sol/Str 1.0-1.6 8.85-14.16 600V 40 amp ABB ZS16 terminal block 4-24 awg 10-20 awg Sol/Str 1.6-2.4 14.6-21.24 600V 60 amp ABB M6/8 terminal block 8-22 awg Sol/Str .08-1 8.85 600V 50 amp Ideal 452 Red mre%"".r 8-18 awg Sol/Str Self-Torque Self-Torque 600V I Ideal 451 Yellow W;GN T 10-18 awg Sol/Str Self-Torque Self-Torque 600V Ideal,In-Sure 10-14 awg Sol/Str Self-Torque Self-Torque 600V WAGO,2204-1201 10-20 awg 16-24 awg Sol/Str Self-Torque Self-Torque 600V 30 amp l WAGO,221-612 10-20 awg 10-24 awg Sol/Str Self-Torque Self-Torque 600V 30 amp f a Dottie DRC75 6-12 awg Sol/Str Snap-In Snap-In ESP NG-53 4-6 awg Sol/Str 45 2000V 10-14 awg Sol/Str 35 4-6 awg Sol/Str 45 ESP NG 717 10-14 awg Sol/Str 35 2000V Brumall 4-5,3 4-6 awg Sol/Str 45 2000V 10-14 awg Sol/Str 35 Table 2:Minimum wire-bending space for conductors through awall opposite terminals in mm(inches) Install approved fittings and/or strain Wires per terminal(pole) reliefs to the EAST,WEST and SOUTH side Wire size,AWG or 1 2 3 4orMore walls and complete wiring installation. kcmil (mm2 mm (inch) mm (inch) mm (inch) mm (inch) Populate the junction box using the 14-10 (2.1-5.3) Not Specified - - U$ appropriate wire connectors,terminal ..Attach lid using (4) #10 x 3/4" SS Hex head oom 8 (8.4) 38.1 (1-1/2) blocks,or other needed components. screws provided.Tighten until snug. 6 (13.3) 50.8 (2) - Intertek 5025824 EZfSOLAR PHONE:385-202-4150 1 WWW.LZS0bTPR0DU0TS.0 ersolarproducts.com I info@ersolarproducts.commaking solar simple. DRAWING NUMBER: SS