7902 EVERGREEN WAY 2024-11-08 - Laserfiche WebLink

NOTES HARDWARE Full size mounting pattern will be provided I THIS SIGN IS INTENDED TO BE INSTALLED IN MOUNTINGCHART � ❑ p p � Access behind wall for install and servicing (118, ¢ w with each letter set. // ^ ifaccess hatches can not be provided. ACCORDANCE WITH THE REQUIREMENTS OF lLi ARTICLE 600 OF THE NATIONAL ELECTRICAL 1/4"ZINC PLATED STEEL _ 1 — CODE AND/OR OTHER APPLICABLE LOCA THREADED THRU WALL • • • FOR ` —— 1/4"LAGS WITH SHIELDS • LAYOUT — D o_ CODES.THIS INCLUDES PROPER 1/4"LAG BOLTS • TEMPLATE<<--—— GROUNDING AND BONDING OF THE SIGN. --- ---- ---- - 1/4"TOGGLE BOLTS • GENERAL CONTRACTOR NOTE: MOUNTING oil HARDWARE _ MINIMUM 1/2"PLYWOOD SUPPORT IS 10'-29/16" REQUIREDTO BE PROVIDED BYTHE o O GENERAL CONTRACTOR 3/8"ZINC PLATED STEEL THREADED THRU WALL 000 ELECTRICAL 3/8"LAGS WITH SHIELDS • Location of Access POWER SUPPLY AND AMP CALCULATOR 3/8"LAG BOLTS • panel 12" x 24" NUMBER NUMBER OF TOTAL Hz 3/8"TOGGLE BOLTS • (or full length under soffit) OF LEDS 60w POWER AMPS NOTE: SUPPLY 1.)THREADED ROD WILL BE STANDARD -ALL OTHER HARDWARE IS TO BE PROVIDED 57 1 0.7 C0 BY THE INSTALLER AS REQUIRED 2.)DESIGN INTENDED FOR NO GREATER ° ° ° ° (DOUBLE CLICK CHART TO UTILIZE CALCULATOR) THAN SECOND STORY MOUNTING o °° ° o a HIGHER ELEVATIONS REQUIRE REVIEW Dealer to provide electrical, 9 4 1 11 1 1 1 0 Max 6'from Middle of any signs, (55 Agilight Mods) unless otherwise agreed upon. LED LAYOUT Project Account manager to discuss and verify the best installation hardware required per each site,and 4 II 0.040 Aluminum Return advise with separate Memo note to Anodized Aluminum Coil , the plant for the type and quantity,Or installer will provide hardware. -� - -- White#7328 II 0.177 Acrylic Faces 1/4"0,31g.Lags into the plywood support beh use spacers perletdcrashingtheACMpanel RETURNS Anodized JEWELITE White#7328 3 3-4 minutes per letter AGILIGHT ULTRA 450 ALUMINUM Coil. Meta lic SILVER 0.177"Acrylic Faces LED MODULE(LS-U450-65K-B150-A) 2"x 3/16"spacer w/1/4"0 hardware as req d 2 _ Ventex we location transformer box(PN#18TB-TPO) Low voltage electrical wires placed O Ventex disconnect switch w/boot(PN:84675) inside 1/2"0 BX Cable and Seal tight 1/2"x 6-0"long liquid tite conduit Connector if the site condition requires. Whip to owner provided power supplyto owner provided power supply 14 AWG LED lead wires(PN 11402R)" °� �- Dealer: PIERRE BUICK GMC 60w agilight slim power supply(psl 2-60wsl-1 00-277v) 9/16"Paige wall buster(98-p0014)IT Street: 7900 Evergreen Wa 1 I_3mm ACM Back_I g y IMPORTANT City,St: Everett,WA For free standing tower with Access panels: 1"Trim Cap I� GENERAL CONTRACTOR NOTE: 1)Backer pre-installed, 2)use3/16"to1/4"-1"long. 1/4"WEEP HOLES MINIMUM 1/2"PLYWOOD SUPPORT IS REQUIRED TO 3)9eal with silicon after#3 above. BE PROVIDED BYTHE GENERAL CONTRACTOR AS 4)install the unibody TYP Wall Section: WELL AS ACCESS DOORS(10X24") UNDERNEATH Fascia Inst.SCALE:N.T.5 ACM panels over plywood (OUTSIDE)THE BULKHEAD FOR INSTALL AND support and 2x6 Wood framing FUTURE SERVICING This document is the sole property of Architectural Account: GMFI Drawn by: MRA Graphics, Inc., and all design, manufacturing, reproduction,use and sale rights regarding the same Project Title: DNL White AGI Rep: S.Frazier are expressly forbidden. It is submitted under a Scale: NTS Approved by: confidential relationship, for a special purpose, and the recipient, by accepting this document assumes 2655 International Pkw . Virginia Beach VA 23452 Date Created: 03/05/2023 Date Revised: custody and agrees that this document will not be Y r 9 copied or reproduced in whole or in part, nor its AGI PHONE: (757) 427-1900 - FAX: (757)430-1297 contents revealed in any manner or to any person www.AGI.net , except for the purpose for which it was tendered,nor any special features peculiar to this design be incorporated in other projects.