3003 W CASINO RD BLDG 45-206 2024-12-05

Cerberus PRO 1 '• 1 • • • • • • 50-Point System Enclosure (cont.) The Model FH901-U3/ R3 enclosure for the 50-point panel is comprised of a dual-mounting setup that allows the main - board to be partially mounted in a lower-to-upper position. When temporarily installed in the lower position, technicians are allowed more space to install field wiring at e the time of system set-up. Additionally, the enclosure supports an optional battery bracket (Model FHA901-U1) that can be used to secure batteries up to 12Ah. Model FHA901-U1 is required to comply with seismic certification, pursuant to ASC / SEI 7- 05,Section 13.2.2. A flush-mount trim kit (Model FHA902-U1 I R1) is also Model FC901 is an addressable FACP that provides a cost- available for use when flush mounting Model FH901-U3 I effective solution for simple fire-alarm-system applications. R3. Model FC901 contains one (1) built-in DACT and two (2) Remote Annunciator (not approved for use in Canada) NACs. Small and compact in design, Model FC901 is ideal for small fire-protection applications using no more than 50 addressable points: ■ retail outlets 1 strip malls ■ doctors'offices ■ dry cleaners - ■ restaurants ■ banks,etc. The dimensions of Model FC901 (connected to a one- height-unit enclosure) are approximately as follows: Used exclusively with the Cerberus PRO 50-point FACP, the 16.25"[41.3 cm.](H)x 18"[46 cm.](W)x 5"[41.3 cm.] (D) Remote Annunciator (Model FSD901-U3 I R3) shows The weight (without operating unit or batteries) is existing status of the Model FC901 FACP. approximately 9 Lbs [4082 g]. A built-in RS-485 serves as the interface between the remote annunciator and the Cerberus PRO 50-point FACP. 1 • • Components Up to eight(8) remote annunciators are supported for each 50-Point System Enclosure 50-point fire system. A 3.5-inch (8.9 cm) by 1.5" (3.8 cm) LCD screen will show details of the event in alphanumeric form. The display screen can be scrolled to reveal additional events. Each screen supports 182 characters: seven (7) lines with 26 characters per line Remote Peripheral Module(with RS-485 interface) The Remote Peripheral Module (FCA2018-U1) provides a means of connecting a Cerberus PRO panel to a parallel printer for creating a hard copy of system-status and configuration reports. This supervised, intelligent module contains built-in transient protection and plain-decimal addressing. • Model FCA2018-U1 is remotely connected to the Model The Model FH901-U3 1 R3 enclosure for the Model FC901 FCA2016-U1 RS-485 communication bus from any FACP is available in either black or red, and supports all Cerberus PRO system enclosure. Model FCA2018-U1 uses system modules. The enclosure also supports 12Ah 'Class B' (Style 4) or'Class A' (Style 6) wiring, and provides batteries. two (2) RS-232 (serial) ports and a single parallel port that Note: For systems requiring larger than 12Ah batteries, use a allow connection to the parallel printer(Model PAL-1). UL Listed battery box. When Model PAL-1 is used with the remote peripheral When field-wiring installation is complete, the main board module, Model FCA2018-U1 supervises the printer for On/ shall be moved to the upper position for standard mounting Off Line, Power On, Paper Out, Paper Jam, and wiring-fault prior to applying power to the system. conditions, as required by UL for NFPA 72 proprietary systems. Event and report printing is generated at the operating unit on the main Cerberus PRO system. Siemens Smart Infrastructure—Building Products —8— usa.siemens.comlfire