Laserfiche WebLink
PS SERIES <br />6 Amp and 10 Amp, 24 Volt Power Supplies <br />The PS Series are independently configurable <br />power supplies, allowing you to pair any input <br />with any output, and feature LED diagnostics <br />for troubleshooting. <br />The PS Series is a remote power supply line from Gamewell-FCI. The HPF-PS6 is a 6 amp <br />and the HPF-PS10 is a 10 amp, remote power supply with battery charger that maybe <br />connected to any 12 or 24 volt fire alarm control panel (FACP) or used as a standalone <br />power supply. The PS Series provides 24 VDC power for NACs (notification appliance <br />circuits) configured as either Class B or Class A (requires the ZNAC-PS option card) with <br />multiple sync protocol options. The PS Series also provides auxiliary power, constant or <br />resettable, suited for detectors, annunciators, door holders, and other fire alarm system <br />peripherals. The PS Series cabinet can hold two 7 AH or 18 AH batteries and can charge up <br />to 33 AH batteries in a separate cabinet. <br />FEATURES AND BENEFITS <br />• Up to five (6 amp model) or seven (10 amp <br />model) independently -configurable, power - <br />limited output circuits for: <br />—Class B and/or Class A NACs <br />—Class B and/or Class A resettable or non- <br />resettable 24V auxiliary power <br />—door holder power <br />• Converts from Class B to Class A wiring <br />without losing any outputs using the ZNAC- <br />PS converter card (sold separately) <br />• Optimal for powering four -wire smoke <br />detectors, annunciators, and other system <br />peripherals requiring regulated power <br />• Optional addressable control, monitor, and <br />relay modules and power -supervision relay <br />(EOLR-1) <br />• Configurable for ANSI' Temporal 3or <br />Temporal coded output <br />• UL-Listed NAC synchronization using <br />System Sensor', Wheelock', Gentex°, or <br />AMSECO° appliances <br />• Synchronization can be triggered from <br />FACP NAC/remote sync outputs, cascaded <br />power supply, or a control module, single or <br />multi, which may be housed within the <br />power supply cabinet <br />• Ability to cascade up to four power supplies <br />• Two (6 amp model) or three (10 amp model) <br />fully -isolated input/control circuits which <br />can be programmed to any output <br />• Two Form C normally -closed trouble relays <br />for AC Trouble and General Trouble <br />• 6 or 10 amp full load output, respectively, <br />with 3 A maximum/circuit <br />• Individual NAC power and trouble LEDs for <br />diagnostic efficiency <br />• Trouble history mode fordiagnostic support <br />• Wide range end -of -line supervision value <br />(normal: 2-27K ohms) <br />• Selectable earth fault detection (enable or <br />disable) <br />• AC trouble report delay timer <br />• Completely configurable via onboard DIP <br />switches, no extra software required <br />• Self-contained in compact, locking cabinet <br />constructed of heavy gauge steel with a <br />corrosion -resistant powder coat chip and <br />scratch -resistant finish <br />• Cabinet designed with ten double <br />knockouts and a removable door for ease of <br />installation and wiring <br />• Includes integral battery charger capable of <br />charging up to 33 AH batteries <br />• Cabinet can house two 7 AH or 18 AH <br />batteries <br />• Battery charger may be disabled via DIP <br />switch for applications requiring larger <br />batteries and external battery charger <br />• Removable terminal blocks accommodate <br />up to 12 AWG (3.1mm2) wire <br />HPF-PS6110 <br />HPF-PS6110B <br />Works with any UL 864 FACP which utilizes <br />an industry -standard reverse -polarity <br />notification circuit <br />HPF-PS6/10 include the- Honeywell Power <br />Products lock set (PN:17059) and key (PN: <br />17051) <br />Honeywell <br />bom6nm <br />k1[TM% l� l <br />