Laserfiche WebLink
2 3 4 5 6 <br /> IDYKEMAN <br /> DESIGN <br /> I L - I - L L - - - - GENERAL NOTES <br /> A. REFRIGERANT PIPING SHALL BE INSULATED WITH 1"MINIMUM PIPING <br /> INSULATION,INCLUDING CONTINUOUS INSULATION AT ALL SUPPORTS <br /> E W/NO THERMAL BRIDGING E <br /> B. ALL PIPING SHALL BE PRESSURE TESTED <br /> C. REFRIGERANT PIPING CONNECTIONS SHALL BE BRAZED CONNECTIONSCONSULTANT: <br /> ONLY <br /> D. REFRIGERANT PIPING IN PLANS SHOW ROUTING FOR BOTH SUPPLY <br /> I AND RETURN PIPING <br /> I E. OUTSIDE AIR DUCTWORK AND PLENUMS SHALL BE INSULATED TO MIN <br /> R-11 <br /> F. COORDINATE FINAL DIFFUSER AND GRILLE LOCATIONS WITH ARCH <br /> RCPs AND ELEVATIONS <br /> G. LOCATIONS AS SHOWN ARE APPROXIMATE.CONTRACTOR SHALL E C O T O P E <br /> COORDINATE EXACT LOCATIONS WITH LIGHTS,PIPING,EQUIPMENT, <br /> I ETC <br /> H. DUCT-TO-EXHAUST FAN CONNECTIONS SHALL COMPLY WITH 2O18 <br /> WSMC 506.3.2.3 <br /> I. DUCT-TO-HOOD JOINTS SHALL COMPLY WITH 2O18 WSMC 506.3.2.2 <br /> — — — _ J. PRIOR TO THE USE OR CONCEALMENT OF ANY PORTION OF A GREASE <br /> DUCT SYSTEM,A LEAKAGE TEST SHALL BE PERFORMED PER 2018 - <br /> ���// WSMC 508 <br /> K. A PERFORMANCE TEST AND CAPTURE CONTAINMENT TEST SHALL BE <br /> CONDUCTED PER 2018 WSMC 507.6 AND 507.6.1 <br /> L. PROVIDE RATED ACCESS DOORS WITHIN 10'OF EVERY CHANGE IN <br /> I DIRECTION GREATER THAN 45 DEGREES PER 2018 WSMC 506.3.8 • <br /> M. INSPECT AND VERIFY THAT DUCTWORK HAS BEEN TESTED AND <br /> I INSTALLED PROPERLY PRIOR TO APPLYING DUCT WRAP MATERIAL <br /> N. GREASE DUCT RESERVOIRS MUST BE CONSTRUCTED PER 2018 WSMC MOOR f� <br /> 506.3.7.1 <br /> I 0. DUCT CLEANOUTS SHALL <br /> 506.3.8 AND 506.3 gBE PROVIDED AND INSTALLED PER 2018 2p\.O1 <br /> WA <br /> WSMCti�oG� <br /> I P. GREASE DUCT BRACING AND SUPPORTS SHALL BE CONSTRUCTED �' {{��//�� z <br /> AND INSTALLED PER 2018 W$MC 506.3.3 <br /> Q. DUCTS SERVING KITCHEN EXHAUST SYSTEM SHALL BE CONSTRUCTED 55029 'vim <br /> OF MATERIALS IN ACCORDANCE WITH 2O18 WSMC 506.3.1.1 AND OF, RfCI5iE0.E� \�� <br /> 506.3.1.2 f`rS/t7NALE�G <br /> I <br /> EXISTING HEAT PUMPS <br /> (NOT IN SCOPE) a SHEET NOTES <br /> I 1 INSTALL GREASE DRAIN OUTLET AT LOWEST POINT OF HOUSING AND TENANT <br /> J DRAIN TO GREASE RESERVOIR PER 2018 WSMC 506.5.3 <br /> 2 ALL GREASE DUCTWORK SHALL SLOPE BACK TO HOOD AT 1/4"PER IMPROVEMENTS <br /> FOOT PER 2018 WSMC 506.3.7 <br /> 3 ALL GREASE DUCTWORK SHALL INCLUDE FIRE WRAP PER 2018 WSMC <br /> 'I 506.3.11 AND SHALL BE INSTALLED PER WSMC 506.3.11.2.PRODUCT <br /> FYREWRAP OK TO INSTALL AT ZERO CLEARANCE TO COMBUSTIBLES F 0 R <br /> 4 SEAL AROUND DUCT AT ENTRANCE TO SHAFT.ENSURE DUCT IS 6 <br /> INCHES FROM SHAFT WALL PER 2018 WSMC 506.3.11.1.FYREWRAP IS H O P E W O R K S <br /> NOT REQUIRED WITHIN SHAFT <br /> I <br /> EXISTING HEAT PUMPS AT <br /> "QTINB°DPE) --- --------L <br /> 3315 BROADWAY <br /> EVERETT, WA <br /> - - - M2oo - - - - - - ,3' BID SET <br /> - n <br /> y 08/29/2022 <br /> City of Everett Permit Review <br /> I 4 EVEeETr Status:Reviewed for Permit <br /> — — — 09/28/2023 10:50:04 AM <br /> F- — <br /> I Thls drawing is: <br /> C <br /> 1.Copyright 2017 Dykeman,Inc. <br /> 2.The Architect's Instrument of Professional Service. <br /> 3.For use on this project only.Obtain Architect's <br /> 1 written permission for any other use or reproduction. <br /> PROJECT <br /> KE-1 <br /> 20121-031 <br /> I • <br /> MARK DATE DESCRIPTION <br /> — V — / <br /> B B <br /> • <br /> PRINCIPAL IN CHARGE:I <br /> PROJECT MANAGER: I <br /> PROJECT ARCHITECT: I <br /> JOB CAPTAIN: <br /> I <br /> I <br /> I I I <br /> - � - - - - - - - - - - - - - - - - - � <br /> i I I <br /> DRAWING TITLE: <br /> I <br /> I <br /> i I I <br /> A MECHANICAL - A <br /> ROOF PLAN <br /> DRAWING <br /> o- <br /> E G � <br /> 1 <br /> MECHANICAL - ROOF PLAN ° 2' 4 8' <br /> Scale:1/4"=V-0" Z <br /> 2 3 4 5 6 <br />