3625 BROADWAY SONIS KITCHEN 2025-01-03

SECTION 3-SYSTEM COMPONENTS R-1 o2 Restaurant Fire Suppression Manual R-102 Restaurant Fire Slrppresskxn Manual SECTION 3-SYSTEM COMPONENTS UL EX3470 ULC EX3470 UL EX3470 ULC EX3470 PAGE 3.2 REV.11 2014-SEP-01 2014-SEP-01 REV.11 PAGE 3.3 REMOTE MECHANICAL RELEASE SINGLE TANK ENCLOSURE ASSEMBLY REGULATED ACTUATOR ASSEMBLY OEM RELEASE/BRACKET ASSEMBLY The Remote Mechanical Release(Pan No.433485)is used The Single Tank Enclosure Assembly(Part No.429870)Is used The Regulated Actuator Assembly(Part No.429850)contains the (FOR OEM IN-CABINET USE ONLY) to actuate up to five R-102 regulated actuators.The remote in double and multiple-tank systems and must be mounted to regulator,pneumatic actuator,expellant gas hose for agent tank The OEM Regulated Mechanical Release/Bracket Assembly mechanical release utilizes a 101-10 carbon dioxide cartridge a dgld surface near the regulated release or regulated actuator hookup,and enclosure knockouts to facilitate installing expellant (Part No.79493)contains the same regulated release mecha- as the actuation pressure to operate the regulated acuuamrs. assembly its expel tent gas line will be connected to. piping,This assembly is used in multiple-lank systems and must ntsm as the standard AUTOMAN Regulated Release Assembly, The release Is housed in a stainless steel enclosure. The enclosure Is designed for mounting either a 1.5 gallon(Part be mounted to a rigid surface. The OEM Regulated Electrical Release/Bracket Assembly(Part Also available is an OEM Remote ReleaselBracket Assembly No.429064)or a 3.0 gallon tank(Part No.429862)in a mini- 1'he regulator contains two outlets 13�apart.One outlet is It c ntains')f is Identical to the Mechanical VACsolversion except that g � It contains a factory installed 120 VAC solenoid and electrical (Part No,439946).The OEM Remote ReleaselBmckel contains mum amount of space. used to Interconnect the expellant gas hose to the enclosed switch.These releaselbracket assemblies must be Installed In the same release mechanism as the standard Remote Release, agent tank.The other outlet connects an expellant gas line to a sutable equipment enclosure-either hodzontally or vertically. and must be installed In a suitable equipment enclosure either ENCLOSURE ASSEMBLY an additional enclosure or bracket assembly.The regulator is horizontally or vertically.The remote release contains all the .designed to allow a constant flow of expellant gas Into each They contain all the necessary mounting and conduit holes need necessary mounting and condut holes needed to fully install �— .agent tank at 110 psi(TO bar). needed to fully n the assembly.The agent tank Is Installed NOTE:At�Nr TANK MUST separately and n need not be bracketed once it Is piped and filled. the assembly.Note:OEM Release/Bracket Assembly roust be BE ORDERED 0 The pneumatic actuator Is designed to puncture the expellant Note:OEM ReieaselBracket Assembly must be inslaited high installed high enough In cabinet so that there is suRclem room SEPARATELY. 6 [I (SEE PAGE 331 gas cartridge seat upon receiving pressure from the regulated enough in cabinet so that there is sufficient room to in to install and remove car(ri stall and S cartridge. a release assembly actuation piping.The enclosure contains a remove cartridge. 1 knockout to facilitate distribution piping hookup. .'Nona:OLM Regolntcd ElecBkal R431easelarxrkel Assembly 1Pat No.437324)N 6 -1 Inwnkd to bo osad w11U electric der.U.n. REGULATED ACTUATOR ASSEMBLY MOUNTING m o RELEASE ENCLOSURE_i NOTE:AGENT TANK MECHANISM MUST BE !0 b MOUNTING H ORDERED PNEUMATIC RELEASE BRACKET SEPARATELY ACTUATOR MECHANISM---�, (SEE PAGE 3-3) ASSEMBLY 0 SHIPPING 13 LR I5.9 1g1 i REGULATOR b I REGUtATUR FIGURE 3.5 a SHIPMNC,Wt. GI ZIPPING WExx17: 9.3 La(4.2 ka1 14 4 LB live kill RED PAINTED BRACKET ASSEMBLY SII La 18 WT. ' s3u(es killFIGURE 3.4 The Bracket Assembly(Part No.429878)is used in double and °0045' multiple-tank systems and must be mounted to a dgid surface near the regulated release assembly or regulated actuator FIGURE 3-7 . FIGURE 3-9 orola awes assembly that Its expellent gas line will be connected to. The lank bracket is constructed of mild steel and painted red. AGENT TANK ASSEMBLY OEM REGULATED ACTUATOR ASSEMBLY N is designed for mounting the tank in a minimum amount of The agent tank slipping assembly(3 Gallon(Part No.429862) The OEM Regulated Actuator Assembly (Part No. 418691) space.The Bracket Assembly can only be utilized with 3.0 gal- and 1.5 Gallon(Part No.429864))consists of a stainless steel Includes the regulator,pneumatic actuator,expellant gas hose ion tanks(Part No.429862), tank and an adaplorllube assembly.Tire adaptor/tube assem- anti OEM bracket.Also available is an OEM Regulated Actuator bly contains a burst disc.The burst disc prevents agent leakage Assembly with all IITa above mentioned components except for BRACKET ASSEMBLY due to significant temperature fluctuations in the area where the bracket.This assembly is Part No.418522. MGNNnNG the tank Is located,Under normal conditions,the tank requires RPAcxET hydrostatic testing every twelve years.The date of manufacture is stamped on the tank nameplate. a The tank is shipped uncharged and must be tilled with only ANSULEX Low pH Liquid Fire Suppressant during installation. B TANK AnnPTaw ✓ TUBE ASSEMBLY B 0 3 GALLON SlnIPPING WT. T La o.3 ko 1.5 GALLON SHIPPING WT. o . 8LB(2.3%0 - ti 11ING Wr.4 LP(1,5 k91 'E AGEN TANKT ' FIGURE 3,-10 5HIPPING WT.a LR P.,k<j) '— 6 •i FIGURES-6 FIGURE 3-6 ,A,I